Finishing
2,922 topics in this forum
-
Would someone care to offer a basic overview of the essential differences among various finishing options - or perhaps point me to somewhere where it's already been done? I browsed 12 pages of posts in this forum and didn't find it. I'm getting (back) into some weekend woodworking these days, and I'm more than a little bit confused. TIA.
-
-
- 7 replies
- 7.6k views
-
-
First off, I am a complete finishing noob so please excuse my ignorance. Anyway, I just finished a new aquarium stand and I skinned it in 1/4" oak plywood and trimmed it with stain grade pine moulding. After much research I have discovered that the pine and the oak will be difficult to blend and achieve a uniform color. I have learned that dying and then staining the two different species can help them blend more effectively. Would you guys dye and then stain, or would you just use something like General Finishes merlot stain and seal it? Any advice on finishing this project would be greatly appreciated. Thanks...
-
- 1 reply
- 2.6k views
-
-
Hello everyone, I'm about to finalize a tabletop for a garden table made from douglas fir. I used wood that I acquired from some guy nearby who sold the remaining bits from a tree that was chopped down a couple years ago. The wood wasn't particularly pretty and included several defects (but it was very cheap and thus ideal for my first table). Planing the stuff was a nightmare and cutting around the knots not much of an option as I had barely enough wood. The result is simple: I have a few knots with voids in the top and I'd like to stabilize them. It's a bit late for plugs (some are too large anyways) thus making me think of epoxy. I want to use an oil based finish …
-
- 4 replies
- 2.9k views
-
-
I'm looking to spruce up a cutting board using this technique: http://www.woodsmith.com/files/issues/173/adding-an-epoxy-inlay.pdf My question is this. I finish all of my cutting boards with mineral oil and beeswax. According to this article, they suggest spraying a coat of lacquer to seal the wood before applying the epoxy. As I don't want that epoxy on the surface of the cutting board, is it easy to sand through or will it absorb fairly deeply into the wood? I'm not that familiar with sprayed lacquer, so I don't really know its tendencies. Thank is advance! scott
-
- 5 replies
- 5.7k views
-
-
I'm making a solid cherry coffee table for a friend, there will be a glass insert for a large part of the top! I'd like to use Watco Danish oil, to bring up the grain and color! After several coats of WDO, can I go over that with a Matte Polyurethane? My buddy is a scooter tramp that's finally settled down, but, He still has party's with our old scooter tramp friends, and I know that the table will get a lot of abuse, Beer, whiskey, pizza and who knows what else will be all over that table! I need to know if the 2 finishes will work together. And will the poly be better protection than WDO alone?
-
-
- 3 replies
- 2.9k views
-
-
So I am refinishing some large Douglas Fir beams in a house I am restoring. I thought I would be a little bit fancy and stain them with a black gel stain, wiping off quickly to let the grain through. I am using an Old Masters Gel stain. I have attached a picture below with the desired effect. The problem I have is that one of the beams (the most prominant one of course!) won't absorb the stain. I have tried many things - but it just won't take (see second photo below). My guess is that I oversanded the beam. I used a random orbital and went down to 100gr - but when I feel the wood now it feels almost burnished - smooth like when you over-polish something. I guess …
-
- 8 replies
- 33.5k views
-
-
I'm a beginner woodworker, and even more of a beginner when it comes to finishing. I built a little wine rack, which is little more than a box with an X in it. Got a little creative and put in some ebony splines to add an accent. Still needs some more sanding and clean up. Now it's time to think about a finish. I have not developed the ability to do much other than a very simple finish, such as a wipe on varnish. And I do not have access to spray equipment or anything more complicated than a rag or foam brush. I have sanded the piece with 120 grit, and sanded the end grain to 220. I was thinking of finishing this piece first with a layer of Seal Coat sanding sealer (…
-
-
- 8 replies
- 7.3k views
-
-
No not that kind of stripper! I have some poplar cabinets with a cherry stain I'm looking to refinish. I'll strip the faceframes and build new drawer fronts and doors but I haven't refinished anything in 10 years so I thought I'd see what strippers everyone suggests.
-
- 7 replies
- 2.9k views
-
-
Step by step faux painting technique using aerosol cans of lacquer on duplicated fiberglass parts.
-
- 2 replies
- 3k views
-
-
I'm making some book cases out of white oak 2" x 2" and 3/4" shelving. The client is asking for a natural look ie un stained but with a cerused/lime finished look. So white amplification of the wood grain. I've tried to find out on line (youtube etc) but I'm struggling to find sufficient, simple first timer type information on the subject. Most of the stuff I've seen is stained a darker color first and then cerused. I need to know what to buy, what I'll need to do the job and a simple (idiot proof) step by step process to get a reliable result... Any takers???
-
- 6 replies
- 22.1k views
-
-
This may be a bonehead question ... but what are forums for? I'm going to be using transtint dyes for the first time for a refinishing project. I'll be using it as a toner with shellac, and the information I've found says to add about 1/8 to 1/4 ounce per pint of solvent. My question is, how do I measure out 1/8 or 1/4 ounce of dye? The transtint comes in 2 oz bottles, and the bottle (perhaps because of the dark red mahogany color) is opaque, so I can't even eyeball it based on how much I'm extracting from the bottle. Can you convert ounces to teaspoons or something? Thanks!! Rick
-
- 11 replies
- 10.3k views
-
-
Like most of you I have used many things in the past to wipe on stains and finishes of all kinds, Mostly cut up t-shirts or random soft cloths, But what is the absolute best thing to use for wiping on a polyurethane finish?
-
-
- 9 replies
- 21.1k views
-
-
Given the 'lather, rinse, and repeat' user-friendly nature of Watco Danish and Teak Oil, I'm wondering if I can go back and re-sand some small inconsistent spots that don't show until the first coat. - a spot from a rogue droplet smear of weaponized airborne wood glue - an area with a irregular (or missed) sanding - a scratch Thanks..after all the time I put in prepping my finish, all I can see are these areas. Attached a photo of one major offender in a cloud lift Thanks
-
- 1 reply
- 3k views
-
-
So when i was a young pup Mtv blasted me with images of rockstars and cool looking guitars. Admit it for flashy guitars you can't beat the West coast in the 80's. So one of the guitars of my child hood I remember was good ol C.C. Devill from poison. Say what you will I always liked the guy and thought he had some great guitars. So in my late night Ebay searching i came across this diamond in the rough. I Brand new B.C. Rich gunslinger with a crack in the body. So with a quick bid and a oh hell I can fix that and $100 later it was mine. Now.... what to do with it well it starts with this. Untitled by XBIGJIMX, on Flickr Untitled by XBIGJIMX, on Flickr Now here i…
-
-
- 16 replies
- 3.6k views
-
-
Hey guys, I was helping a friend rub out his polyurethane finish on his bar. He had allot of brush marks in it. First we wet sanding with 600 grit, then 0000 steel wool. Everything went well except now all the grain and joints are full of white poly dust, basically it looks terrible but it's smooth. lol Of course another coat of poly will make it disappear, But then we would have to rub it out again and most likely have the same end results. What is the best way to clean out all the dust from the cracks. It seems to have stuck and clumped together from the wet sanding. A vacuum did not work. I want to get it all cleaned before I do the final rub with paste wax and 000…
-
- 9 replies
- 3.1k views
-
-
I would like a new spray system. Have cheap Rockler hvlp. Thinking earlex but don't really know. I do spray a lot of paints so that will need to be an option. Typing on cell phone. I apologize for any typing errors.
-
-
- 27 replies
- 7.5k views
-
-
Hello all, I'm a cabinetry student just finishing up the course and I've made a walnut and purpleheart (w brass inlay) wine rack and I was wondering what the best way to finish it might be. Basically I have two options: 1: sprayed lacquer, which we've pretty much used on everything thus far. The only problem with it is that there are some pretty tight and awkward spaces and I'm afraid of getting too heavy a coat where the gun would be so close to the surface. (I thought of pre-finishing, but opted against it.) 2: There is a small store nearby that carries a few supplies, but the only real option among them is a Minwax Tung Oil Protective Finish. Having gone through all o…
-
-
- 5 replies
- 3k views
-
-
Good Afternoon All! I have ahead of me a task of staining and finishing a few unfinished pieces of pine furniture. I am a newbie at staining and finishing so I have some questions that way I can do it right the first time. First I want to stain the wood with a cherry stain(minwax). Should I use a pre-stain? After the stain dries and I get the desired color, I wanted to finish it with Linseed oil. Should I sand the stain before applying the boiled linseed oil? But my I want the finish to be more protective. Can I apply polyurethane over the boiled linseed oil? These pieces of furniture are being used for a computer desk, so I would like it to be able to handle poss…
-
- 4 replies
- 9.4k views
-
-
Hi, I am new to this forum and happy to have found you out there. I have found an 1760 (give-or-take) George III Wash stand in very good condition. However the varnish has gone very dull and the wood must have dried out over the 250 years or so and made cracks in the main wood and the outside veneer. We live in South Africa and the humidity is much drier out here. I am not too worried about that but would like to restore the old varnish without having to sand the whole project down. This would certainly take away the beauty of this piece. I have now read that some people use Danish Oil after having cleaned the object with turpentine? I mix my own as we can't buy the pro…
-
- 3 replies
- 2.7k views
-
-
My wife bought a sideboard yesterday that probably dates from the '20s and it has that smell unique to old furniture. What is that musty smell and how do you get rid of it? Spit coat of shellac perhaps? Sent from my iPhone using Tapatalk
-
- 2 replies
- 3k views
-
-
I built a cabinet out of RO ply. The shelves are dado-ed. I was doing some stain matching to existing store bought furniture - what a nightmare that was. I had to apply two stains and coat of amber shellac to get the color even close, but it is close enough. Anyway, I'm putting on the wipe-on-poly and suddenly there are dark bands about 1/2" wide around the shelves/dadoes. I did not see them before the poly went on, now they are quite noticeable. They must have been there before the poly, but can't say for sure. I've seen this before and it seems it happens by wiping stain cross grain along joints. I tried not to do that, but who knows what happens after an hour …
-
-
- 2 replies
- 2.9k views
-
-
Hello All, Big fan of the site and the info came in handy when building a cedar patio table with hidden coolers last fall (it turned out well enough judging by the offers). I purcahsed a foreclosed home a year ago and replacing the doors is my last reno project. The old hollow core doors are in the trash and all of the new 2 panel solid core oak (vaneer) doors are fitted and ready for finish. I have Kobalt HVLP guns (one gravity and one canister) that I would like to use for this project but I really need some assistance. I have about 3 years of HVLP experience (body shop job during college) but I have never sprayed wood finish. So here is the plan and a…
-
- 1 reply
- 2.7k views
-
-
Hi - I have been working with wood all my life and really enjoy it and have always strive for nice finishes. But right now I am trying to find this Restoration Hardware brand table. It is supposed to stay weather with a distress look . I cant figure out how they did this stain I have tried everything oil and latex stain I have and now trying a mix of using vinegar and steel wool mixed and add brown latex so it doesnt come out grey it comes close but doesn't make it. I had to take the old finish off and now i have to make it look old looking again and match this color light faded brown and match the legs . Of all my 40 plus years of woodworking I fi…
-
- 7 replies
- 3k views
-
-
I've been trying to find the right color for a kitchen table top and everyone has suggested doing a sample to get it right. In my case, my top is mostly Birdseye maple. To test the color, I made a sample color board with lots of different dye concentrations. I made this from a 1x4 from Home Depot . I also put the same concentrations on the end (to be cut off) of one of my Birdseye boards. Underneath both was a conditioner (Charles Neil's). No Blotch which I'm happy to report, but I find the home Depot board to be very much lighter than the samples on the birdseye board. Can anyone provide an explanation, and more importantly a fix? I will of course test another B…
-
-
- 4 replies
- 2.9k views
-
-
Hey guys looking suggestions on this shelf. I found it in my fathers attic and am starting to sand it. Looking for suggestions on finish. I have no idea what kind of wood it is. Here's a picture after I wiped dust off with wet rag. Not completely dry. Sent from my iPhone using Tapatalk
-
-
- 10 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·