Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing

  1. I just got done building my first desk and now I would like to accomplish the finish in my render. I believe I will need ebony for the top, but I'm not sure how to get this deep maroon semi-gloss finish so that it looks like the image. I would like it to be as close as possible. This desk is made of Red Oak and Radiata pine for the frame. (I might replace the pine 1x2's with oak if the slight difference in the finish doesn't have the aesthetics I want.) What would you do to achieve the finish in the render? How would you clear coat/finish the desktop to protect it from writing, water, food, etc?

    • 6 replies
    • 3k views
  2. Started by KristyR,

    I purchased a table that looked innocent at first, but after bringing it home, I have realized just how intricate the wood is and how difficult the staining of this table may be. The center is a kind of gunstock color that fades past the inlay into a Cherry or Red Chesnut. I've included pictures but they don't accurately reflect the exact color. The camera distorted them just a bit. Is this a situation where the same stain will affect what I think may be different woods causing the fade, or is this a technique that I will need to do to achieve the same result? ANY help would be so greatly appreciated!!!

      • Like
    • 16 replies
    • 3.3k views
  3. Started by Candice,

    This is a small table. It's probably 100+ years old. I see no indication of any kind of finish. Can you identify the wood? Advice for cleaning any dirt/residue sitting on the surface? How should I restore this piece - remove the dark and light rings, and other discolorations? What's the best I can do without stripping it to bare wood? Thanks! Full table top Left side of table top - where most of the damage is

    • 7 replies
    • 3k views
  4. in october,'13 I started branching out from my regular custom furniture gig to more carpentry oriented woodworking. the project that has landed in my lap is quite an undertaking. to restore and refinish 96 2'x5' interior louvered wood blinds. the blinds are about 100 years old and in very good functional order, considering some of the frames are sagging due to glue failure or broken tenons. some louvers are split or the hardware is missing. most of them are gobbed up with many layers of paint which prohibit them from functioning well. the whole point of this projects is to make sure they are squared up & functional again, which would mean taking the gobbs of paint off…

      • Like
    • 12 replies
    • 6.5k views
  5. We have picked up a number of old/antique pieces through the years because we just love old wood. Many have finishes that have faded, have build-up, may be dirty, and/or suffered surface damage. In a few cases, I scratched off the old flaking finish and have left the bare wood with just BLO. I realize now that we have some treasures and I'd like to give them the treatment they deserve. 1) I'd like to do a general cleaning first so I can take a good look at what each piece needs. Can I use something like Murphy's oil soap or lemon oil on all of them - bare wood, shellac, varnish, etc.? Should I use something else? 2) One large piece has a sun-faded side. Is th…

    • 10 replies
    • 7.1k views
  6. I believe this dresser is walnut. I don't know finishes, but my guess on this is shellac. It's very close-to-the-wood. Overall, the finish is in good shape. This dresser sits with one side to a window. That window side and lower front have been lightened by the sun. The upper front is lightened, but not as much. There is a darker area near the base. I can't tell if it's dirt. It doesn't rub off with my finger. * I'd like to give this a gentle cleaning (also see if that lower darkening is dirt) - what should I use? * I will not be refinishing this piece, but I'd like to give it some support. Is there something I can do to help the lightened wood? Thanks for any…

    • 0 replies
    • 3.6k views
  7. Started by Dnorris1369,

    Wondering how you guys fill nail holes and such when using stain. I can never seem to (hide the filler) Sent from my iPhone using Tapatalk

      • Like
    • 17 replies
    • 4k views
  8. Started by pdovy,

    I ripped up carpet of the stairs in my basement recently and discovered a nice set of old oak steps, but they are in dire need of refinishing. I spent some time this weekend trying to get to it but realized in order to do this in any reasonable amount of time I'm going to need a good quality detail sander to hit all the corners / edges. Any recommendations? Of course, I have been eyeing the Festool RO 90 DX, but not sure I can justify the price tag - I have a serviceable 5" DeWalt RO sander already. Are there decent options between the cheapo "mouse" sanders you can pick up for $40 and the Festool? Paul

    • 8 replies
    • 3k views
  9. Started by Candice,

    I found beautiful fir under the old linoleum in the kitchen of my 1929 house. I want to finish the fir with a satin finish and encourage a little amber, if anything. I can't move the major appliances out, so I have to prep and refinish in sections. I have to use the kitchen while I prep, so I'd like to do something to seal as I go. Will this approach work? * Sand a small section * Apply BLO * Apply dilute (50-50) shellac for seal and some protection * Come back and finish half the floor with shellac * Finish second half and blend where they meet (probaly in a 2' wide passageway) I was considering an oil, then danish oil, then varnish series, for moistur…

    • 8 replies
    • 3.3k views
  10. I'm finishing up with a new desk that I designed but I've never stained anything before. The desk is a majority Red Oak and the framing/supports are made of Radiata Select Pine from Home Depot. I would like to make it a two-tone finish where the framing and supports are a different color than the cabinets and desktop but I'm having a hard time imaging how I should stain the two to compliment eachother. Does anyone here frequently build two-tone furniture that can offer some suggestions? I was thinking of a stain that brings out both of the species natural colors but I'm not sure how well they would contrast each other. Something similar to this desk made of maple and cher…

  11. Started by jgdusc,

    I need to finish a cypress big green egg grill table. It will be sitting on our front porch which at times will be exposed to the elements depending on the how hard and which way the wind blows. Sunlight partially but rarely direct. I have read so much my head seems like it will explode. Hoping you guys can help me out. Right now condisidering using either General Finishes Outdoor oil, or Old Masters exterior penetrating sealer. But after reading thinking about the CPES but who knows. SInce it will be exposed to grease or bbq drips not exactly sure. Let me know your thoughts. Thanks!

    • 8 replies
    • 13.1k views
  12. Started by rodger.,

    Typically, I use solvent finishes. After the finish has cured for a week or so, I typically use 0000 steel wool and paste wax to "finish the finish", as Marc says. I have recently switched over to spraying water Bourne finishes. Any tips on rubbing out a water based finish? Some people have posted that steel wool should never be used with a water Bourne finish due to rusting issues, but I can't see how it would rust if the finish is cured and used after the final coat. Perhaps they are referring to between coats. I have also read that some people use mineral oil and wet dry sandpaper, while others use mineral spirits and wet/dry paper. Any advice for a newbie to…

      • Like
    • 18 replies
    • 13.8k views
  13. Started by Dnorris1369,

    Hey guys I will be finishing up a jewelry box for my wife tomorrow and I really didn't think ahead on this. I made it out of red oak and purpleheart scraps. Main part of box is oak Middle strip of ph on lid and some trim in ph. I have never used purpleheart on anything but a cutting board. Any suggestions appreciated.

  14. Started by Nick2cd,

    I don't have an HVLP setup yet, but would like to start researching them a bit. I'm curious what the most common finishes are to spray through these units. Right now, I tend to use a lot of wiping varnishes (thinned poly), lacquers, or the BLO/poly/mineral spirits trinity. What do u guys spray on your pieces most commonly?

  15. Started by mcfinewoodwork,

    I recently built a small folding table out of poplar. It has green streaks in it that, of course, will go away with time. I know that oxalic acid will eliminate the wait but I would rather let time do the deed. I put a stain and a few coats of poly on a test piece and it made the green pop out even more. I want to use it in the mean time. I don’t mind the green so long as it goes away after a few months to a year. I don't know if I could wait longer than a few months though. I have it basking in the sun while I make this decision. The question is, am I prolonging the aging process by sealing the poplar? Should I just suck it up and use the acid wash? Or skip the t…

  16. Started by Chuck Melton,

    I think it would be nice to put together a thread of basic finishing information as the basics of it are glossed over in many of the instructional videos I've seen. Does anyone have any favorite finishing resources they would care to share?

  17. Hi All I've poked around the site a bit trying to find an answer to my question but no luck (may be more of a taste thing). I am in the process of building a butcher block workstation out of hard maple for the block and reclaimed walnut for the base. I've done some wire brushing and light sanding to the walnut but I'm not quite sure how I should finish it? I'm going to be using Watco butcher block oil for the top but I need suggestions for the base? I don't want to alter the color of the natural wood but I do wan't to protect it. I don't have the ability to spray a finish so I will have to wipe or brush it on. I appreciate any and all suggestions. Thanks,

  18. Working as lead finisher in a smallish cabinet factory, I am responsible for all stain and sealer application. I will be quite honest in saying I have a lot to learn, and could use any advice offered. Currently my setup is a small binks pot for dye stains and 'fog' stains, and a large 5 gallon pot for wiping stain, I have a long stationary table/bed of nails and a small portable bed of nails, complete with a 55 gallon drum/garbage can with a board on top for a wiping table. On an average day I can spray between 240-350 pieces depending on application required (fog vs. wipe). I guess my main question would be in regards to meeting production expectations and still mai…

  19. I've got an Earlex 5000 and am about to get a second paint cup (L0190). I'd like to use it to store finish between coats, but it seems that it doesn't come with a lid. Has anyone been able to find lids that fit the cup - a bit of searching on the 'net hasn't yielded me any results. Thanks! -d

  20. Started by tinyacorns,

    Hello - this is my first post! I'm building a zebra wood keepsake box - the first time I've worked with this particular wood. I'd like to ask if anyone has advice for finishing this beautiful wood - and specifically, if I should use filler before applying the finish. I plan to use a danish or thinned tung oil, but I'd welcome any advice on how to really make the grain pop. Thanks! -- tinyacorns

      • Like
    • 10 replies
    • 19k views
  21. I have custom cherry cabinets first made & stained in July 2013. Stain was applied with a black glaze put over the entire stain - the end effect is relatively dark, almost a walnut color. There were alot of little dark spots on the finish of raised door panels so the manufacturer (an Amish manufacturer in Indiana - I did not deal with them directly - I contracted with a KD/installer who has been doing kichens for 14 years) took the affected cabinet doors back, stripped & restained in November 2013. I am now noticing in the last couple of weeks that on a couple of doors, along one edge of the raised panel where it meets the stile, there is a vertical line where …

    • 8 replies
    • 3.1k views
  22. Started by Speghetto,

    I recently order an unfinished hard wood maple fireplace mantel with the intent of staining it the same color as some recently installed cabinets. Rather than trying to color match the stain, I went ahead and purchased a quart of the cabinet stain directly from the cabinet manufacture. To my surprise they sent me a quart of solvent-based "NGR" (non-grain raising based on internet searches) and a quart of solvent-based "Wipe Stain", with directions stating that I should let the NGR dry for 5 minutes before applying the Wipe Stain. Additionally, the mantle manufacture strongly suggested that I treat the maple mantle with wood conditioner prior to applying stain in order …

    • 13 replies
    • 8.6k views
  23. Started by wtnhighlander,

    I recently finished an oak accent table with straight boiled linseed oil. After the third coat was applied, the temperature dropped, forcing me to bring it in from my unheated garage. The oil wept out of the pores for about 3 days, then became dry to the touch. After about 3 weeks, I noticed there were tiny gummy lumps forming on the surface. They wipe off with a clean rag, but does anyone have a clue what conditions might cause this?

    • 4 replies
    • 2.8k views
  24. Started by mar10,

    We have a queen size pedestal bed frame that is 35 years old (see pictures attached). There are scratches and wear on the side rails. I would like some advice on refinishing it. Does it need to be sanded down to the bare wood? I believe the wood is either pine or fir. Do you think that it would be cost effective to have someone refinish it? What would be a reasonable fee to have it refinished? Any comments are appreciated.

  25. Started by Sammalammadingdong,

    First off, sorry for the double post! I think I posted in the wrong spot before. Straight and to the point, house fire, threw these pieces in storage, sat for 2 years. Soot damage http://i.imgur.com/Mu7IcX7.jpg http://i.imgur.com/EEtKjTj.jpg http://i.imgur.com/8dLdBYo.jpg I'm scared I'm going to ruin the furniture trying to fix it but figured its already ruined so why not give it a go. Going to start with just wiping it down and maybe re-post the results. Guess the question is...is it OK to use just water? I also have no idea what type of wood this is. Both tables have a little metal stamp that say "The Bonny Shire Collection", but I still can't fi…

    • 10 replies
    • 3.1k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.