Finishing
2,922 topics in this forum
-
Does anyone have recommendations on how to keep a walnut slap as light of color as possible? This is for a bench and the unfinished wood is quite mellow- almost creamy. I have tried watering it to see what it might look like finished, and it get's fairly dark. I'm hoping to avoid this. Should I use a sealer of some sort? Plan on finishing it with some sort of poly, and leaning towards GF water borne poly but would take recommendations on that also. Many thanks crew.
-
-
- 11 replies
- 14.6k views
-
-
I recently got a job from a friend to make a bench seat for her kitchen table. just a simple 2x2 legs, 1x3 rails, 3/4" 16x46" seat. mortise and tenon'd rails into the legs. Just a few hour project. The problem being, her table is painted stained almost black, looks almost painted. What would be the simplest way to get get that dark with some stain. Or dye, or what ever. not paint though. I've built a reputation for refusing to paint wood, so I gotta stick to that. Thanks.
-
-
- 31 replies
- 11.2k views
-
-
I made some stiles for a chest of drawers and cut one too short. Stupid shooting board. Why are they so fun? I didn't want to make a whole new stile because it would require using a different board and that would screw up the color match on the rest of the stiles. I made a patch to make up the gap (maybe 1/8" - 3/16" thick). No one other than us will probably know but I'd like to try to match the patch as best I can. It's a little lighter than the rest of the adjacent pieces so I think I need to take an artist brush to it. The good news is I haven't glued anything up so I can work on the piece if I want to without worrying about the pieces next to it. Here are…
-
- 7 replies
- 2.9k views
-
-
I was wondering what the best way to finish yellow cedar? i'm thinking of making doors and window frames but i need to know how to finishing interior and exterior. i know that yellow cedar has it's own oils and preservatives which makes it difficult to work with. i'm looking for something to complement it natural looks and preservation.
-
- 3 replies
- 13k views
-
-
Okay, I have a project where I need to laminate a piece of plywood with galvanized steel sheet. I've laminated a plastic laminate on to plywood or MDF many times with contact cement. Anyone out there know if contact cement will hold galvanized steel sheet to plywood? ... Any other thoughts on what to use? In case you are wondering it is 18 gauge galvanized steel and about 3 feet by 3 feet.
-
- 17 replies
- 23.3k views
-
-
Hi all Recently purchase an Earlex 4500 for spraying tasks in my small home workshop. We are currently doing up our spare room and turning it into the master bedroom. Leaving a whole bunch of built in furniture in the new spare room. I want to respray all the built furniture. I think it's made of either MDF or some type of blockboard. It's got a very shiny thick film on it that looks really plasticky. What should I do to prepare for spraying or can I spray straight onto that film? Any advice would be appreciated. Thank you. Dave
-
- 2 replies
- 2.8k views
-
-
I am making a bed out of cedar, I have the typical yellow cedar along with the red and white- I need advise on how to finish it- I would like all the colors to "pop" - any suggestions?
-
- 2 replies
- 3k views
-
-
Hi Everyone, I recently installed beautiful unfinished mahogany windows in my apartment. Because the color of the window casing was a slightly different Mahogany and there were small wood putty filler, we decided to do a light stain to make the windows appear more uniform and the results were gorgeous. We are about halfway done and this morning everyone in the apartment building insisted we cease work because the varnish applied at the end is so toxic that people are leaving the building with sore throats and itch eyes. We had tented the area and opened all the windows but somehow in this old pre war building, the fumes are filling all the other units, even 4 flights …
-
-
- 4 replies
- 2.9k views
-
-
So I'm building a jewelers bench for my wife. It's made of ash and with walnut accents. I'm going to use pre mixed amber shellac on the base, how many layers do you think I should use? I'm going to have to finish it in my basement, because I work in an unheated garage in Vermont. My other option is to ,if he's ok with it use the boat builders shop a few houses down. I'd like something durable but will take abuse on the top. I wish I could post a picture here but the mobile version isn't so friendly for that. Thanks in advanced... -Justin
-
- 6 replies
- 2.9k views
-
-
To start off with, i have almost no experience with wood apart from what I've recently done with my exposed beams at home. So I've completely stripped the paint off the beams in my kitchen with a belt sander then sanded down to 240 grit with a orbital sander. After applying some poly I've realised it starting to come up blotchy, did some research and found out applying a diluted version first may help. It did a little but it's still noticeable. Now I've seen pictures and videos on the net of what blotchy wood looks like, and it looks much more natural compared to what I've got in the kitchen. It looks like maybe the belt sander had something to do with it? maybe …
-
-
- 4 replies
- 3.1k views
-
-
Ive not ventured into doing much more than clear poly from a rattle can on my projects, but I have a project in mind that I will be using a spray gun to finish, and I see a lot of talk of sanding sealer, but anytime I've used it, I didn't notice any benifit to it? So what exactly is the purpose of it? Sorry for the noob question, I'd like to expand my finishing techniques.
-
-
- 5 replies
- 6.1k views
-
-
I recently got an MDF table top for my lathe, and I would like to seal the exposed bottom since it will be in a partially climate-controlled room (garage). What would you use? Oil based primer, shellac??????
-
-
- 8 replies
- 6.1k views
-
-
Attached are the two boards that are going to make up the table I am making. The base is going to be made with cherry. I am hoping to be done with the woodworking part next week. Then comes the tough part. I have never worked with claro walnut before so I am not sure how I should finish for a durable good looking top. I would prefer something that looks natural and not like plastic. I have used WATERLOX ORIGINAL SEALER/FINISH for other projects, but I am not sure if I should use it here. What about enduro-var or Arm-r-seal? Should the pores be filled and if so with what? I have heard doing it by sanding with oil and creating a slurry. Any thoughts would be apprecia…
-
-
- 9 replies
- 8.1k views
-
-
In the house we're moving into, the 30-year-old particle board kitchen shelves (inside the cabinets) are sagging to the point I'm just getting rid of them. In our current house, I caught the problem before there was too much sagging and reinforced the shelves around the edges by supporting them with 3/4" square cleats all around the edge rather than those little peg things. So I'm going to do that for these shelves but I also need to remake the shelves themselves. I've cut down a bunch of 1/2" Baltic Birch ply and faced the front edge with a strip of solid ash that I got on a ridiculous sale. Now, I need to pick out a finish. The original plan was just some latex paint be…
-
- 13 replies
- 20.9k views
-
-
So I have a bunch of HVLP test boards and one thing are the walnut ones have tiny random pinholes that only happen over the pores. This has happened with both General Finishes High Performance and Old Masters Poly. I spray a bunch of test boards at a time and the hard maple, white oak, and red oak don't have these pinholes so I don't think it's technique. The final surface is glass smooth and the pinholes aren't really noticeable under normal light but are in my bright shop. The walnut had a water-based dye applied then 1# coat of Zinsser SealCoat. I'm guessing the pinholes have to do with the size of the walnut pores and white and red oaks bigger ones aren't affected…
-
-
- 5 replies
- 4.1k views
-
-
A friend asked me to fix his folding table, and I am trying to figure out the best way to go about this.... This table consists of 4- 2'x4' plywood tops that fold down around the collapsed legs. they are attached by piano hinges. when collapsed, this table is only about 6" thick... pretty neat... Anyhow.... due to user error in opening the table, one of the leaves snapped off right at the screw line where the piano hinges were attached... What i am trying to figure out is if I can somehow fix this piece without having to replace the entire leaf. Will any combination of screws, dowels or epoxy be strong to hold up to the stresses of opening and closing th…
-
- 1 reply
- 4.2k views
-
-
Hey all. Our shop has been approached by a restaurant/kitchen design company to strip some old commercial restaurant table tops, so that they can be refinished. We are not repairing the veneer, just getting down to bare wood. What would be the best way to do this? Is simply sanding off the old finish an option, or do we have to use chemicals? What chemicals would be safe to put on veneer? I don't want to destroy the glue. They gave us one table top to experiment on. I can post a pic if it would help (just don't have one currently). It appears to just be finishd with stain and poly.
-
- 0 replies
- 2.9k views
-
-
Still a bit new to woodworking - I've built a small desk (about 4' x 2'), and am about to start applying finish. I'm planning to brush on poly on the desktop surface, but not sure if brushing it onto the sides would cause issues. If brushing poly onto vertical surfaces is troublesome, would it end up looking fairly uniform if I: - brush poly onto the desktop surface, and - create a wiping poly for the sides by diluting with mineral spirits? Thank you for any input; Best regards, Matt K
-
-
- 13 replies
- 22.5k views
-
-
Looking to make some wooden rings and some 1/2" wood earring plugs. Is any finish going to work
-
-
- 8 replies
- 3k views
-
-
I live in the Northeast and during the winter months I have no way of finishing my projects because it's too cold and damp in the garage. I'm considering building a dedicated stand alone finishing room attached to the back of the garage. What do you recommend for heating and humidity control. Thanks.
-
-
- 1 reply
- 2.9k views
-
-
I was told to use a conditioner on new cherry if you are staining it to avoid blotching. Does anyone have experience with these?
-
-
- 12 replies
- 4.9k views
-
-
I recently turned a bowl out of olivewood and I would like to, first, carve a design, using a Dremel, into the bowl and, second, burn the pattern, with a burning tool, that I just carved so that all the lines are black. However I haven't been able to find any information on what finish I should use over something that has some areas burned and others untouched. Any thoughts about this would help! Thank you
-
- 3 replies
- 2.9k views
-
-
I built a farmhouse table from pine 2x6 boards. I found an English Chestnut MInwax stain that I like. I tried sealing the stain with Minwax satin wipeon poly. It seems to be a little to shiny for my taste. Can you suggest something that will look a little less shiny and still protect the wood from water spots and other damage? Thanks, Judy
-
-
- 8 replies
- 13.8k views
-
-
Hello all, for my first project, which will be a contemporary book shelf, I will use 1/2" birch plywood. Initially black phenolic faced plywood was the material of choice but this stuff is really hard to get and expensive. Therefore I decided to make a kind of test shelf with baltic birch plywood first before I order the expensive stuff to see if I can build it the way I want it, which basically means with the necessary precision. It will be a little smaller and can go in the basement as storage space if the result is not convincing. The nice thing about phenolic faced plywood is the fact that the surface is already prepared and there is this nice contrast between th…
-
-
- 8 replies
- 6.8k views
-
-
This has been my go to mission recipe for many years. I'll modify the dye and/or stain to change the color but it's always the same steps. I got a Fuji Mini Mite 4 in the spring and finally getting some good practice with it since fall is here. I'm really enjoying all the benefits of a waterborne topcoat and the results are great. I've settled on General Finishes Enduro-var or High Performance as I'm having success with each. Here is my long-time Waterlox varnish recipe: - Lockwood American walnut water based dye mixed 1 lb. in 4 gal. ratio - Zinsser Sealcoat dewaxed shellac - Varathane Gunstock oil based stain - Waterlox original oil based varnish - 50/50 mixture…
-
- 8 replies
- 8.5k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·