Finishing
2,922 topics in this forum
-
There is a picture of the skeleton of the coffee table below, I am also sharing it in project journals. Trying to decide on a finish type. Will get some abuse (3 kids under four years old) so looking for the right balance of durability and ease of repairability. I've got an earlex 5500 so I can spray if that is best. I was thinking spray lacquer (although this would be my first time with lacquer which makes me a little nervous). Do you think there are better choices? Second question: should I finish prior to assembly? Thanks!
-
-
- 2 replies
- 2.8k views
-
-
I have a nickel sized, 1/16” deep tearout in a birdseye maple table top. I’ve sanded it out partly but fear it will be a ton of work to sand down the full diameter required to hide the mark (I’ve done about 2” this far). this happened due to my inexperience with a plane . I will be staining the maple with a relatively dark TransTint dye over Charles Neil's Blotch Control. I am thinking of leveling it out with epoxy prior to spraying the dye stain, followed by Arm-R-Seal topcoats. Thoughts? I am hoping given the dark dye (Dark Vintage Maple) the epoxy outline/blemish won’t be too noticeable? Would appreciate if someone can confirm the dye OVER epoxy (West Systems) is saf…
-
-
- 3 replies
- 3k views
-
-
Finished this little box up. Paduak and tiger maple. Finish suggestions??? Sent from my iPhone using Tapatalk
-
- 6 replies
- 2.7k views
-
-
I've done my first engraving with red oak (actually any hardwood), and i'm not sure how to stain/finish the project. Here is the piece: I'd like to make the color and grain pop and bring out their richness. I figure i'll do a top coat poly or shellac to give it a satin sheen. Just not sure on how to stain it with the nooks and crannies of the inset text.
-
-
- 15 replies
- 7.3k views
-
-
Hello- I wonder if anybody knows if tinting waterbased satin lacquer black will leave those odd fingerprints that sometimes show up when you paint something black that is handled a lot such as kitchen cabinets? I tried Sherwin Williams low shine waterbased All Surface Enamel and it left spots where you touched them. I cleared it up by spraying on a semigloss varnish, I did the same on some other more difficult cabinets and the sanding left white dust that really screwed me up. So I am looking for an alternative. The local Sherwin Williams breaks down a five of their clear satin KEM AQUA into one's for the smaller user, but I have never used the product. I am painting …
-
- 1 reply
- 3.4k views
-
-
I'm going to start finishing a project today. Each round of spraying will last about a minute. I'm going to do 5 coats per side. Finish is lacquer. Do I need to empty the cup after each coat or can I let the finish sit in the cup for two days? What if I were to use water based poly?. Adam
-
-
- 9 replies
- 13.5k views
-
-
I am relatively new to spray finishing, having sprayed only about a dozen real projects. I use an earlex 5500, which I really like. Anyway, I was spraying a project today, trying to get it done in a timely fashion. I skipped filtering my finish before pouring into my gun. DONT SKIP FILTERING. I got a hundred "blobs" in my finish. Little pieces of dried finish that shot out of the gun. So now I have slowed myself down, as I have to wait for it to dry and then sand them all out.
-
- 2 replies
- 3.2k views
-
-
Hi Everyone. I made a 7' long x 2' wide table top that is going on a metal frame. Five boards and (this is a little weird) they are cherry, qs oak, sapele, walnut and another cherry. Depending on your taste, it came out nice. I have always heard that you need to finish both sides of a top to prevent warping. I learned this once the hard and painful way on a much smaller piece. My finishing plan is this. 2 coats of BLO followed by dewaxed shellac (Zinzer seal coat - does nice things for depth and color in my experience) followed by probably three coats of Arm-r-Seal gloss. I have oiled both sides already, but do I really need to do everything, all coats, on both sides…
-
- 6 replies
- 3.4k views
-
-
I've never used Resin and I thought it may be the best option. I have a 2 inch thick piece of an oak tree with a great 5-6 inch open knot hole in the middle. It also has some nice character on the edges. I thought a clear resin may allow for a nice table top and display this beautiful wood. Is this a good option? Is another way better? What is the best way to get started? Thank you for the help.
-
-
- 6 replies
- 3k views
-
-
Hi All, This is my first post so I hope all is clear. The image I have attached is a piece of walnut veneer I have removed from a staircase column I am repairing. This project includes removing and repairing damaged veneer as well as refinishing it. This home is 20 yr. old with custom woodwork/cabinetry throughout. After removing the staircase rails I was able to see the walnut veneer in it's original state. ( see attached image ) My challenge now is to identify the stain or process that so radically changed the color of the walnut? I can't speak as to why walnut was used if they were going to lighten it so much? The railing parts are white oak. My g…
-
- 1 reply
- 3.1k views
-
-
Please let me know if you foresee problems using spar varnish on a wood surface for a bathroom vanity. The plan is to apply it to a wood bath counter under a vessel sink. We will be using it as a bath vanity.
-
- 11 replies
- 23.9k views
-
-
This is a simple faux paint using just artists oil colors and aerosol cans that can be done by anyone at home.
-
- 2 replies
- 2.7k views
-
-
I match a LOT of stain colors and come up with finish schedules all the time for large production and custom jobs. Any tools I can find to help me I am all over. UTC colors are notoriously messy to get from the can. These mix lid/dispensers from Fillon are one of my favorites. They work awesome for cans of stain also. No mess from either quart or gallon cans and they make using my gram scale extremely easy. Rockler sells the Mixing Mate which looks like the same product to me and costs more. You can buy the automated shelf which has an explosion proof motor to keep your tinting colors mixed or they have a convenient handle to mix manually. I just bought a dozen and they w…
-
-
- 4 replies
- 2.8k views
-
-
Hi folks. I am planning to redo my countertops in my kitchen and bathroom. I purchased some butcher block material made up of jointed red and white oak. I would love to finish them with a thick layer of polyurethane but that is not food safe. Can anyone tell me what finish would have a beautiful appearance like varnish or polyurethane and be resistant to scratches from knifes and be waterproof but also be FDA approved and food safe? Thank you very much for your suggestions in advance.
-
- 5 replies
- 4.6k views
-
-
Hey all, I should've tested it first, but its too late now... I used Helmsman satin, however it dried like gloss. Added another coat thinking maybe it would change...just as glossy. Any help? Thanks
-
-
- 6 replies
- 21.1k views
-
-
I'm a beginner and my first project is a maple edge grain island countertop. I'm looking for some direction as I complete "her" with the finish. 1. After my final sand with 220, I really like the natural look and don't think I want to stain it dark or possibly at all. I want it darker than it is which I assume the Arm R Seal will do. However, any direction on how to pull out the natural beauty of this maple without getting it too dark or too light? Would a Linseed oil be appropriate? 2. Secondly, as this is a countertop, does anybody have a special precautions related to food safety and the finish? Appreciate the community of learn eras and sharers on the for…
-
- 10 replies
- 8k views
-
-
I am getting ready to use some BLO for the first time but am little unsure on how I should properly dry the used oily rags. I don't really have good spot on my driveway to let them dry nor do I have a clothes line to hang them on. I was just thinking I could put my weber in the middle of the yard and let the rags dry on the grill. If by chance they did combust they would just burn off in the grill. Any thoughts or other suggestions would be great.
-
- 11 replies
- 5.2k views
-
-
Hello all - I wondered if anyone has had any experience successfully removing cigarette smell, without having to refinish an entire piece. I recently acquired a pair of mid-century dressers that are in fantastic shape, but after getting them home I quickly realized these babies reek like they’ve been used as ashtrays for the past 40 years! The original finish is nearly perfect, and if at all possible I’d like to avoid having to remove it. But, I think I’ve exhausted most potential remedies – sunlight, vinegar solution, restore-a finish, feed and wax, more sunlight….I’m at a loss! Any thoughts would be greatly appreciated!
-
-
- 8 replies
- 4.8k views
-
-
This may come off as a beginner question, which is good, because I am! HA! Everyone mentions using rags for applying finishes, but nobody mentions what kind of rags. I have tried using shop towels (http://www.amazon.com/SCOTT-Shop-Towels-12-rolls/dp/B00139WFOG). They are nice because they are relatively cheep, and they hold up decently, except they do tear if they catch a rough edge. Do you use rags like these, old tshirts, or do you buy a box of cotton rags? If you buy rags, which do you use? It seems if you use tshirts, you would run out, so would you ever reuse them? Any info would help! Thanks!
-
-
- 10 replies
- 2.9k views
-
-
I am working on stripping an old interior door and have all the old paint stripped off and there is some green in the wood I have used chemical and sanding on it with 120 grit and its still not coming out. I will post pictures later.
-
- 3 replies
- 2.7k views
-
-
I have one of the mid-range hvlp sprayers that I use for clearcoat. I just spray in my shop or outside (depending on weather). One of my biggest challenges is getting the lighting set up so that I can make sure I can see the edge of each pass to make sure I overlap properly etc.. I have a variety of portable halogen work lamps, but it seems that no matter what I do there is always some point in the application where I can't see the last pass and I am basically spraying blind. My shop is in a dbl garage, so the door on the end opens and I can get natural daylight coming in one end if I want to (also helps with ventilation). The main shop lighting is a grid of compact f…
-
- 2 replies
- 2.7k views
-
-
I used to subscribe to staining wood but after working with walnut and cherry, my latest approach is just to use waterlox which is fantastic. Not so fast. I am building a cabin in Colorado and my out-laws come to visit quite often and of course have opinions ... how fun. So my wife's mother told us we should paint our cabinets RED and I freaked. Having a color on wood means the cabinets will never look as good as the day they are finished ... bla bla bla. Two options. 1) Make all my doors and face frame out of alder and stain the wood with something red. 2) Make all my doors and face frame out of balsa wood and paint them with milk pain red ... exp…
-
- 3 replies
- 2.6k views
-
-
Hey guys. Finishing up a wall hanging cabinet. I am using general finishes dye stain. Looking advice on finishing it up. 1. Do I need to use shellac before a topcoat? 2. Thinking of using general finishes water based. Good idea.? 3. Semi gloss Or satin Oh yeah it's tiger maple. Whew almost forgot to put that in there. Lol Sent from my iPad using Tapatalk
-
- 5 replies
- 2.9k views
-
-
Refinishing the top of an antique mahogany vanity simultaneously with a maple kitchen/dining table with 4 leaves. I've not had any problems with the vanity. All was going well until this last coat. In areas on the table it has now crackled & 2 star shaped wrinkles. I'm very familiar with crackling paint & understand the process. I'm trying to figure out what circumstances could create polyurethane to do so that are not in my knowledge arsenal plus advice on what to do without re stripping & starting from scratch. I'm spraying with HVLP in my booth in the garage with filtered ventilation/airflow (I know there's lots of opinions against this) Temperature wa…
-
- 3 replies
- 12k views
-
-
Hi there new to the site and to wood working. I need some advice on this chair's top back support. First you can see its not square, the bottom of the right mortise is about a 1/4" higher than the other so if I bottom the support or top it I will have a gap on one side or the other. If I center it there's a bit of a gap on each. Also, there's a gap between the face of the support and the chair leg that I cant clamp out. It will butt up flat when its attached to one leg only, when I attach the other leg, I cant pull the legs in enough to close the gaps. I think the center and lower supports just dont have the extra play. I was thinking about cutting back the support…
-
- 4 replies
- 2.7k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·