Finishing
2,922 topics in this forum
-
Hi folks, I'm working on a basement bar and just put the first coat of stain (minwax oil-based) on the bar top, which is 5x3/4 unfinished red oak floor planks on top of 3/4" ply. Overall i'm happy with how it turned out but I found one spot with some sanding swirl marks where it looks like maybe a chip got stuck under the sander. I would like to try to fix it but am afraid i'm going to be left with an uneven stain application. Any suggestions? Is there a good way to find this kind of thing before you start laying down the stain? Thanks!
-
- 5 replies
- 20.6k views
-
-
I am building a box for a Christmas gift exchange at our church. The box is walnut and maple with a maple cross in played on a walnut top. The problem I now have is that when I sand with the grain on the walnut I am going across grain on the maple. How do I get the finish I need without going cross grain on one or the other? Obviously this is my first attempt at inlay and had never considered this before I glued the inlay. Should I have prepared before? Any advise would be VERY helpful. Thanks.
-
-
- 10 replies
- 2.9k views
-
-
I am at the finishing stage on a presentation box. First coat was zinsser sealcoat with some dye followed by a good 320 sanding to pop some tiger maple grain. (TWW Grain Popping from episode 32 of the webseries) I then wiped everything down with a rag and a little DNA to get teh sanding residue eliminated and let it dry. Then applied first light coat of Arm-r-seal semi-gloss with a folded t-shirt. I used Marc's wipe on/no wipe off technique and it all soaked in to both the purpleheart and the tiger maple. This morning (8 or so hours after application) I used a grey scotchcbrite pad (the ones from Woodcraft) to rub it out and it dulled it considerably with residue. I…
-
-
- 12 replies
- 16.2k views
-
-
i have used a couple oil based finishes, and I really don't like the Amber tint that happens. I was wondering if anyone has been able to work around this by adding a dye or stain to a oil/varish to even out the color. I am guessing it would take something like a cyan color to shift the final color more neutral. This will likely further darken the wood but I am fine with that.
-
- 9 replies
- 3.2k views
-
-
So my wife tells me last week she wants planters built for the deck by thanksgiving . ( not like I have two other projects in full swing) so of course I drop everything and off to lowes I go. My question is what is a good finish. I'm using pressure treated pine Sent from my iPhone using Tapatalk
-
- 8 replies
- 2.9k views
-
-
ive been commissioned to build a bunch of stand up desks and they want 3 color options. I've built them out of red oak. The first color I used Minwax red mahogany stain and it turned out great. On the second set of desks I used general finishes Java gel stain, and it's pretty dark. But they want the last set to be even darker. What should I do to get a darker finish with it still looking like wood. I don't want to just put on another layer of the jav stain to make it darker, I'd like a darker tone.
-
- 28 replies
- 14.8k views
-
-
Seems every article I read online really gives paste wax a bad rap. Most of which say that once you apply it ,that's it, you can never refinish ever again and you're stuck with it for life. Any attempt at sanding will just spread the disease. Now I think most of these articles are aimed towards folks that want to restore or refinish an old piece. On projects in which I use danish oil (generally as a timesaver), after a month or so, I give it a nice coat of paste wax, be it Minwax or Johnsons, for a little extra smoothness, and a bit of luster. Should I not be doing this? Does it impede my ability to touch up or recoat with danish oil again? Plus, when I giv…
-
-
- 11 replies
- 8.2k views
-
-
Hey folks Is it wise to use waterbased ployurathane for butherblock counters? Just looking for one step easy solution.... Thanks
-
- 7 replies
- 2.8k views
-
-
I am making a batch of Campaign Stools for Christmas Presents this year and wanted some opinions on finishing options. I have made two of these stools for myself in the past and used the recommended wax on the lathe method, but wanted something that would be tougher since I am giving these ones away. These are going to non woodworking homes and will probably be used outside quite often. What do people think about hanging them and spraying something like a polyurethane from a rattle can? Would something like a Deft lacquer be tougher? I know that there are many thousands of ways I could finish these, I am just looking for your opinions and maybe suggestions for applica…
-
- 10 replies
- 3k views
-
-
And by ignorant, I mean REALLY ignorant. I have almost zero knowledge base. However, we were just donated three HVLP spray guns from Anest Iwata (http://anestiwata.com/product/az3-hvlp-s-impact/). But I don't know what to do next. Obviously, I need a compressor, or some sort of airless unit. But I don't know what to look for. We have a compressor, but it is a cheap one from ALDI, and just use it with our nailer and to blow out machinery. If anyone is aware of a general overview so I have some context, that be great. Or, if you just know of the right equipment for this gun, that is helpful. I saw this: http://www.jnequipment.com/show_detail.php?item=253958S%26D_-_Graco…
-
- 3 replies
- 2.9k views
-
-
Hello, I am hoping I can get some help and answers to my perplexing issue. I recently bought this beautiful table from Craigslist and although it's in decent condition, it needs some TLC and a major flaw needs to be addressed. It has these decorative, deep grooves in the top that catch every crumb and make it impossible to keep clean. My kid can't do his homework at the table either because his pencil hits the groove and rips the paper. It just isn't very functional and I would like to make the surface smooth if possible. Is there anyway to fill these grooves? The table is very heavy and appears to be solid wood, although I am a complete novice and don't know any s…
-
-
- 11 replies
- 3k views
-
-
Hi everyone, I found this fan from amazon fairly cheap in comparison to explosion proof fans (http://www.amazon.com/gp/product/B001I4BFWY/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1) to use with a spray booth. Has anyone had any experience with this one? While the description says it can be used for paint booths and VOC removal I want to be sure before spraying lacquer. Sorry for the size of the pic. Sam.
-
- 16 replies
- 6k views
-
-
Hi guys .. I can't decide on what finish to use on this bedside cabinet, it's made from pallet wood and I want to leave all the nail holes and gaps for that upcycled look. I see a lot of this style furniture online and it's either painted white, stained or treated for that aged look. I'm also considering leaving it raw and let it age. What's your preference or can you suggest something new. I do want to sell this piece because I don't have room for it and I was also thinking of letting the customer decide.
-
-
- 6 replies
- 3.3k views
-
-
I've been restoring some old Stanley planes and making new handles and knobs. My first set was done out of cherry that was turned on my lathe and then given a coat of boiled linseed oil and then wiped vigorously with a microfiber rag. I give it about 10 minutes and then apply my first coat of shellac, wait an hour then I lightly sand with gray scotch bright pad, apply another thin coat of shellac, wait an hour and repeat. I do this until I get about 8 coats of shellac. final light sanding and then lightly buff it on a buffing arbor. I really love the way it comes out. Does anyone have any similar methods for finishing? I find this to give me my favorite looking result.…
-
- 1 reply
- 4k views
-
-
I've started using Sam Maloof's natural oil finishing mixture and have noticed white chaulk-like splotches here and there when I use it on walnut. I use a homemade mixture of 1/3 pure tung, 1/3 boiled linseed and 1/3 spar urethane varnish for the first few coats and then 1/3 tung and 1/3 linseen plus some beeswax for the second few coats. I sand up to 400 grit before I apply the finish and I wait a day in-between each coat. I apply all coats liberally, let each coat sit few minutes, and then wipe off thoroughly before setting aside to dry. When completed the pieces look real nice with a very smooth soft buttery feel. But after a few weeks I notice that when viewe…
-
- 5 replies
- 3k views
-
-
Strippers of stain of course. . I have been working on a solid oak door with deep raised panels. The stain that I used on the panels looked great in a small area but has turned away too dark on a larger surface. Only the 4 inside panels are currently strained. My question is with proper chemical stripping / sanding, will I be able to lift enough stain out that when I stain the entire door it won't look ridiculous. Keep in mind I have not had the need to strip stain up until now I am hopig to go from golden oak to colonial maple. .
-
- 1 reply
- 2.7k views
-
-
I am to the point that I am going to paint my new mobile base. But which kind of paint should I use? Do I need to prime the wood? I am going to spend my shop time tonight filling some holes and adding some screws to beef up the base. Then I plan on sanding everything to 150g or 180g
-
-
- 3 replies
- 2.9k views
-
-
http://ths.gardenweb.com/forums/load/wood/msg0508251620915.html?15 Hey guys. So I have been building an exterior wood door for my parents house in California. They are in a very temperate climate with maybe only 2-4 inches of rain per year. When researching what I could use as a good top coat I ran across this article. The meat and potatoes is that using a #4 base neural untinted paint meant for siding provides a durable coat glossy finish with minimal upkeep. I would love to hear your thoughts. Right now, this is the finish I am planning on using do if you don't like it or the idea of it, I would appreciate you giving a durable alternative.
-
- 2 replies
- 2.9k views
-
-
I'm making a small end table out of ash for a friend of mine. There are quiet a few defects/voids in the wood that sink into the workpiece. I want to fill these in with clear epoxy and brass pigtails from Craft Supllies USA (link at bottom) I want to use General Finishes Oil Based Java Gel Stain as the finish. Has anyone found a successful way to finish over/around epoxy? http://www.woodturnerscatalog.com/p/162/5254/Turners-Select-Pigtail-Brass-Metal-Inlay
-
- 4 replies
- 17.1k views
-
-
I'm doing a finishing course at the local college, and the instructor has had us do a lot of wet sanding. I'm curious - what's the highest grit you typically wet-sand your top coat to? I did my story board to 1500, but a couple of students took it to 8000 and then used a buffing wheel.
-
-
- 22 replies
- 8k views
-
-
I made my wife a wedding band by turning a titanium sleeve and an oversized turned african blackwood sleeve. I used loctite brand all purpose to glue them together. I knew at the time that it was a short term solution. She has to take it off when she is washing dishes or taking a shower because the wood isn't protected at all. I just purchased a CA glue kit from Rockler woodworking because the reviews looked like it worked well with pen making kits. In your opinion and experience, what is the best way to shield the wood from the elements to keep it from cracking and expanding/shrinking every time the humidity changes? This is the kit I have on the way. ht…
-
- 8 replies
- 2.9k views
-
-
Hello, I used to have a gorgeous old late 1950's Hamilton drafting table that looked a lot like this one: http://www.1stdibs.com/furniture_item_detail.php?id=490882 . It was lost in a move, and I haven't been able to find another one that I can afford, but I did find a similar one of a cheaper make. The top on this one is pine and sort of beat up, but I found someone who has made a new maple top for me. To me, one of the best things about the old table was the smoothness of the top. I work on really thin paper, so that makes a big difference. The original Hamilton top also had a beautiful light amber color, as shown in the link. Does anyone know how they might have…
-
- 7 replies
- 9.5k views
-
-
I had chair seats re-caned (Cesca chairs) and the craftsperson used Minwax stain and boiled linseed to finish the new cane to match the existing seat backs. However, when I got the seats back there are drips down the sides of the wood seat frames. I tried to remove using Howard's restor-a-finish with no luck. Any advice on removing the drips then restoring the finish?
-
-
- 5 replies
- 2.9k views
-
-
I have a small project made from walnut and mulberry. I applied 2 coats of Dark Walnut Watco Danish Oil for color. After waiting 8 hours per the instructions on the can, the surface felt dry, so I wiped on a coat of thinned Helmsman Spar Urathane, as this will be gong outside. After 12 hours, it is still quite tacky. Have I pushed things too fast by coating over the WDO, or is the cooler, damper weather slowing down the curing process?
-
- 6 replies
- 2.8k views
-
-
I hate brush marks, and have never been able to master a brush-mark free finish using one. Some 30 years ago I worked at a woodshop where we did a lot of lacquer finishing with a standard compressor and Binks/Devilbiss style guns. However, these days I'm pretty sensitive to fumes, spray in a home workshop rather than a huge paint booth, and would rather avoid flammables as much as possible. I read a while back about the advances in waterborne finishes and how HVLP eliminates the need for a huge compressor. So I'm now the proud (and befuddled) owner of a Fuji Mini-Mite 4, along with 1.0, 1.3, and 1.8mm aircap sets. I've done a little bit of project painting (cornho…
-
-
- 8 replies
- 2.9k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·