Finishing
2,922 topics in this forum
-
Usually I just wipe them down with food grade mineral oil. However I've been thinking about doing the double boiler, warm the mineral oil and melt beeswax into it and stir it up together and then use that as the finish. It will add a bit more durability and water resistance. Thoughts?
-
-
- 26 replies
- 7.3k views
-
-
Has anyone use this on flat grain cutting boards? How does it hold ?
-
-
- 5 replies
- 2.8k views
-
-
I applied some Waterlox (red can) to a test board last week. Smells like pure gasoline. 7 days later I can still smell it if I put my nose up to the piece. I couldn't imagine how bad it would be on a large project. I was going to finish my new sanding station with it, but it would presumably make my shop unbearable for days. So what's the deal? No other finish I've used smells this strong. Did I get a bad batch? If not, what's the fume off time? (for the record, my go to finishes are Danish Oil or Arm R Seal, which I've noticed take about a month to fume off, but actually smell quite pleasant while they do)
-
-
- 7 replies
- 7.2k views
-
-
Help! I tried refinishing my 13 ft older oak table. I stripped with Citristrip, sanded with 120 twice, scrubbed down with mineral spirits, and sanded again with 220, twice and wiped down. Then I put a 50/50 cut of bullseye unwaxed shellac/ denatured alcohol. Then I started putting on the Java (General Finishes) Gel stain. It didn't take well. I tried to restain to darken it and the second staining actually wiped off the first stain and it is very blotchy. What have I done wrong???? I tried to research each step and do it right. Afraid to continue and have an incredible back ache???? Can I sand back to what I thought was raw wood and start over???? Maybe I…
-
- 4 replies
- 5.7k views
-
-
Hi Guys, I am applying arm-r-seal over cherry die stain on tiger maple. I have a couple questions. 1. What type of cloth do you use for wiping on the arm-r-seal? I have been using cotton t-shirts and struggling with lint. 2. Are there any suggestions for a top coat over the arm-r-seal. Or should I continue with additional coats of the arm-r-seal. I am at 4 coats, sanding with 400 grit between coats. Each coat looks a little better. I am getting impatient with waiting 24 hours between each coat. Thanks, Mark
-
- 3 replies
- 2.7k views
-
-
I have not experienced this until now. I have used GF Dye Stain before on several different projects involving different materials and the same methods prior to staining and finishing. I have used different finishes as well and never had an issue until now. I am refinishing my kitchen table top, it is a pine laminated top from IKEA that I purchased 7 years ago used before my wife and I got married. Now that we have 3 kids the top is scratched and dented so it was time to refinish it. I sanded through the grits to 220 and sealed with Bullseye SealCoat to control the blotching. Then I wiped on GF Light Brown Dye Stain and let it dry. When I went to seal the stain wi…
-
- 18 replies
- 9.4k views
-
-
-
I was wondering today if a person could apply a dye stain to a project, and then use a penetrating oil (like tung oil) over the stain. This way one could have the colour they liked, and avoid a film finish. Or would it make more sense to add the dye to the penetrating oil before applying it? Or is the whole idea just ridiculous? Ideas?
-
-
- 4 replies
- 2.8k views
-
-
ok so i have put 4 coats of arm r seal on my cabinet. I went out this morning and for the most part it is smooth. for the most part is not what i want im hoping i can do better. I sanded between each coat up to 1000grit and last coat had naptha mixed in per marcs video. the sheen looks perfect to what i am wanting. my question is can i buff it lightly without adding another coat or what is my best bet to do now??
-
- 6 replies
- 3.4k views
-
-
I just installed some beautiful panels to the knee wall of my kitchen island. The rails and stiles are solid cherry and the inset panels are cherry veneer, (all unfinished). I do some easy woodworking as a hobby and I have respectable woodworking skills, but due to time constraints, I hired a handyman to install them. Big Mistake! There are some small gaps in the joints between squared panels as well as imperfect 22.5 degree angles. Removing and re-cutting the panels is not an option for a variety of reasons that I will not bore you with. I am reaching out to you for advice about how to fill the gaps to make them as invisible as possible with the abilit…
-
- 10 replies
- 3.5k views
-
-
-
I have a black walnut butcher block countertop installed a few months ago. I have been treating it with Howards Mineral oil. The problem is my kids and I sometimes do work on the counter (homework, etc) and oil spots seep through. I like the natural look and finish, but I have to do something different. What should I do to prevent the oils spots? WATCO butcher block oil and finish ? Waterlock for countertops? Looking for some professional opinions. KJ
-
-
- 7 replies
- 3.6k views
-
-
Hi all! I'm going through a finishing process on an absolute gorgeous walnut table top and I have a couple of questions with respect to my final finishing process. The steps I've used to produce this beautiful piece of work is follows: 1. Sand down 120, 22, 320 using a random orbital sander. 2. Dye using Behlen's reduced 50%. 3. Seal using shellac, 3 coats wiped on reduced 1:1 with denatured alcohol 4. Sand with 320. 5. Finish with Waterlox gloss, 2 coats so far. Pictures: https://www.dropbox.com/sc/gklcucbsi076etb/AADeTmd7PoAok5Wjpm_dRH-Na The conundrum I'm currently having is how to complete my final, 3rd coat of waterlox. I really like the gloss…
-
- 10 replies
- 3k views
-
-
'Restoring' is probably not the best choice of words. My brother in law lives in San Diego and bought a house that came with some nice teak patio furniture. Nice patina, but splinter and crack city and could use to TLC. His ideas to fix them up were not good ones, as like most folks, wood is not his bailiwick. Google search had some pretty bad advice as well, mostly from blogging soccer moms. They've aged naturally, but need a sanding and (maybe?) some additional finishing products. I know teak holds up well on its own. Watco has a Teak oil that I use and like on Spanish Cedar and Mahogany, but I don't (think) it's actually meant for Teak. More of a Dani…
-
- 0 replies
- 2.9k views
-
-
I've been given a barn to dismantle as I wish, and in return I'm building a few pieces for the owners. This piece is incredibly simple. Hatch door for the table top, door headers for legs, joists for aprons. They want it simple and chunky. It's definitely that! I've scrubbed the wood clean and all it has on it now is some dust from sitting in the shop for a few weeks. The 1/4 sanded glass I ordered has arrived, so I'm ready to do something with it. But for all my internet research I cannot find consensus (or even vague agreement) on an appropriate sealer. I just need a matte sealer than will not affect the colour a great deal. I don't mind some depth, but it cannot …
-
- 11 replies
- 5.6k views
-
-
heys just thought i would give you a little bit of a back story before i jump into my questions. In the last year my brother and i have quit our day jobs and started woodworking full time mostly using old skateboards as our material. for those of you who dont know skateboards are made with 7 -1/16" plys of hard maple and different manufactures die the plys with a water based die to keep there boards unique, each company with different color patterns. my brother and i then cut the boards in to different pieces and make turnings, furniture and wall hangings from them. over the 3 years we have been experimenting with them we have managed to work out most of the kinks making …
-
-
- 20 replies
- 5.6k views
-
-
Brief intro, i'm a novice I have built a few things a year for a while, mostly just some shelving units, headboards, frames, things like that. I've always brushed on my finishes and usually just used the readily found stuff at Menards or The Home Depot. Have used some General Finish products before as well. I can get a pretty decent finish i've always been pretty happy with, but it takes me a while which requires me to take up a lot of space for lengthy periods of time. I'll get to my question, I bought the Earlex 5500 after doing some reading on sprayers and getting some advice, no my issue is, i've read enough to know I'm not sure how to start I got a waterbo…
-
- 15 replies
- 5.2k views
-
-
Hello, I would like to refinish a Fender Squier Affinity Stratocaster guitar. To the best of my information, the neck is maple with a rosewood fingerboard. The fingerboard will not be refinished. The maple appears to have a thin coat of a satin polyurethane clear finish. I was wondering if a tinted wipe on polyurethane finish would work to cover the existing finish. If so, any suggestions for brands or techniques would be appreciated. The body will be stripped and then painted. This I should probably ask in a seperate questions. Thanks for any assistance Walker
-
-
- 19 replies
- 11k views
-
-
I am working on a mahogany timber and the wife really want s me to keep it in the "rough". I even have to keep the "paint" on it from the mill. Is there any finish I can use (should I even use any) to keep the look and feel of the rough look? It will be indoors and away from any liquids if this matters. Thanks Bill
-
- 3 replies
- 2.7k views
-
-
Hello, everyone! I inherited some furniture from my parents that I actually grew up with (it's a little older than me - about 50). It's Bryohill Premier Saga - china hutch, credenza & dining set. All are in pretty good shape but the table and chairs need work. Contrary to what I would have thought for early 60's Danish-inspired furniture, the table and chairs (walnut and/or walnut veneer) were finished with shellac. The last step of my thorough cleaning of the pieces was to take an alcohol rag to them, which almost immediately started to drag and stick. I would have they were lacquer or varnish. Anyway.... Because I haven't actually started the restore/refinis…
-
- 5 replies
- 2.9k views
-
-
What is the best way to stain and finish a maple butcher block table top using a walnut stain, (water based/gel/oil)? I will be using Charles Neil's Blotch control for the sealer. Thank you!
-
- 0 replies
- 3k views
-
-
First off, I'm a hobbyist. Mostly build stuff for myself, but have done several projects for hire for other people. Occasionally I am asked to build something for someone and they want it painted as opposed to a natural wood finish. I've generally ho-hum'd these requests and haven't committed to any so far. I got to thinking a while back and realized this: I have limited time in the shop as I work a full time in my career profession. What I love about woodworking is seeing the natural beauty of the wood in the projects I create. I actually dread spending a lot of time on a project knowing that the end result will be covered with paint. So I made a decision…
-
-
- 18 replies
- 3.6k views
-
-
I've a problem. I've taken on a refinishing job and have made a horrific discovery/error. It's a dining table and it the legs were wobbly, so I took the table apart leaving 4 legs, the side aprons and the top. To my knowledge it was clearly a solid wood table. The legs needed repair at the bottom so I sawed off the damage and then moved to stripping off the old finish on the table top before repairing the feet. That's when I found that it was no usual finish. Rather than happily bubbling and peeling away, instead the top began to feel very soft and spongey. Immediately I removed any excess stripper but the whole table has been affected. As you can see from the photos …
-
-
- 11 replies
- 7.3k views
-
-
Hi all, I'm in the process of building a smallish (29 x 48) dining table for a breakfast nook. I'm using African Mahogany and it is going to somewhat Greene & Greene inspired to match my kitchen. Top will have 3" breadboard ends. I plan on finishing the top using GF Enduro VAR - probably 4 spray coats to provide protection for daily use unless I like it so much, I invest in a plate glass for the top. Typically G&G breadboard ends are proud about 1/8" but in this case, my breadboard ends will be flush with the top since that detail would be a pain for dining. I will glue in the center 4" of tenon with screws on each side hidden by ebony details. So a …
-
- 6 replies
- 3.7k views
-
-
For many years, when I built new houses, I needed an airless sprayer a couple of times a year, so I just rented one. Before I understood about the tips wearing out, the ones I rented never worked right like they did in years past. If I had known, I probably would have just bought my own tips, but I bought a spray rig instead, in 1995 (I think). They cost more in actual number of dollars then, than they do now-I expect since they weren't made in China then. It has shot MANY gallons of paint since then. The pump is a .33gpm 2750 psi Graco. The gun that came with it did okay, but it finally got to the point that it needed to be replaced, so I ordered the newest, top…
-
-
- 8 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·