Finishing
2,922 topics in this forum
-
Hey fellow woodworkers, I need a little help please. I recently stripped my fir stairs and applied some clear fir board and batten paneling up the sides and landing. So far I am very happy with outcome, but now the hard part... What would be the best product and application method of a "clear coat" over the stained fir board and batten and the stairs themselves? I have used polyurethane in the past on many projects and was never truly happy with the end result. I also found it a little difficult to apply on vertical surfaces as it tended to run slightly. Oils, varnishes, wipe-ons, varnish/oil blends, hard wax oil, poly, etc etc? Any recommendations? I value each and eve…
-
-
- 3 replies
- 3.2k views
-
-
I have a nice TruStile exterior wood front door. It is a large single panel in their proprietary stile and rail frame. It has square sticking and is about 4 years old. The door was HVLP spray painted with an oil paint. The door gets rain on it regularly as I am in Texas where it doesn't just rain, but usually storms with rain blowing in under the overhang. The door also get sun exposure. So the door is already showing problems with swelling of the lower rail and stiles after a rain. The panel is veneered I think and there are some vertical gaps showing where the paint did not adequately create a contiguous film over the joints. The gaps are less than 1mm. What I w…
-
-
- 8 replies
- 8.5k views
-
-
Never used this stuff before, appearance wise how does it compare to arm r seal? Looking to apply it over QS oak with a good amount of character. It's for a small asian(ish) serving tray which is why I'm looking to use this finish.. Thanks!
-
-
- 9 replies
- 3k views
-
-
Okay. Sooo keep in mind this project is limited to toddler sleepovers so the easiest solutions would be sooo appreciated.. I just stripped, sanded, and wood conditioned the stair treads of my staircase. I applied two coats of oil stain, and the color isn't amazing. It's kind of orange and black, and I'm not loving it. It doesn't look much different after the second coat, so I'm assuming a third coat is both too late (I won't have another sleepover until 3 days from now.. Can I apply something over this to darken it (I'd like more of a dark espresso) or is it too late??!! Pleeeease tell me my options that aren't resanding it hahah Thank you in advance!
-
- 2 replies
- 2.9k views
-
-
I just finished up the humidor. I went with solid walnut and padauk trim. It turned out awesome. I was just gonna rattle can lacquer and rub out finish. I'm not second guessing this idea. Should I try something different. The big problem I have is I usually test scrap pieces but I am all out of padauk except a couple very small scraps. Any opinions appreciated. Sent from my iPad using Tapatalk
-
-
- 9 replies
- 3k views
- 1 follower
-
-
So working on finishing my maple table and have ran into this ... I am not sure the route I should go after reading/watching a lot on it. I would like something that will not amber the stain. I have read that waster based dry really quick which can lead to issues and uneven coats. The oil will give me more time to work it and have better chance of making everything nice and smooth. I just do not know if it is advisable to add an oil top coat over a water based stain. Am I stuck with a water based top coat? Has anyone worked with the below products? Are any better than the others or are they all about the same? As far as applying ... with water bas…
-
-
- 18 replies
- 4.8k views
-
-
A few years back I purchased a day bed from a little antique store here in Las Vegas, NM that was built in Mora County, New Mexico by Civilian Conservation Corps (CCC) workers. There is some lovely traditional hand-carving on it which gives it a very local flair. We just had a screen room built on the back of our house with retractable screens and would like to put it out there. While not directly exposed to the elements it will have some limited exposure when the screens are up. We have just cleaned and sanded it and want to put a sealant or wood preservative on it to protect it from UV and the elements. I don't know what kind of wood it is but it may be a lo…
-
- 5 replies
- 2.7k views
-
-
I am moving soon and I need to dispose of a bunch of finish. I know that I can just harden the latex/waterbased finish and throw them out. I am more concerned with Mineral Spirits, BLO, Shellac and a few oil based finishes.
-
- 10 replies
- 3.1k views
-
-
1st time posting, long time lurker... I had a good friend turn a bunch of cocobolo into speaker connector covers (see pic below showing a representation of what I wanted him to do) as I am building some cables right now for my listening room. I'd like to get a high gloss finish on the cocobolo as my speakers (Aerial Acoustics 6Ts) are a high gloss rosewood as well. I've seen everything from shellac+wax to CA used for a high gloss finish. I have shellac plus some very high quality car wax (Griots Garage Best in Show wax) that are already on hand. I've also seen EEE Ultrashine as a possibility, although its a cut n' polish which may not work over shellac. What have…
-
-
- 20 replies
- 6.7k views
- 1 follower
-
-
Hi Guys, I have been applying GF Enduro-VAR topcoat to a small table top via HVLP spray. This is for a small kitchen table made from African Mahogany. I applied 6 coats because this table will see daily hard use. My technique was to spray the edges before moving on to the top. I sanded all surfaces, including the edges generously with 400 grit after each coat. After the final coat I noticed that the edges had an orange peel like consistency (see photo). I'm not sure what caused this. I figure it was maybe one of the following: 1. I applied too heavy on the vertical edges causing the finish to sag as it cured. 2. Overspray from spraying the top. …
-
-
- 12 replies
- 3.5k views
-
-
Hi. I just built a window casing from vertical grain clear fir. I had plans to stain it and to finish it but once I looked at it I could not bring myself to do it. This wood is just absolutely gorgeous in its natural state with its reddish color and beautiful vertical grain. I realize though, because it is a window framing and a window sill that some sort of preservation will be necessary because the sunlight eventually will make the color disappear and the wood turn gray. Is there anything that I can do that makes the wood look unfinished (and without adding gloss), identical to what it looks and feels like right now, and yet keep it from turning color? Thank you…
-
-
- 7 replies
- 3k views
-
-
Hi there. I'm working with an oak slab aprox 4in thick & 47in around and a piece of camphor approx 9in thick and 58 inches around. Both have dried out for a little over a year. I've leveled and sanded them down and I'm using Formbys tung oil finish on them. A few questions. 1) Is there an optimal amount of coats to apply? Possible to put too many? 2) Would you recommend applying a single coat of low gloss poly after the tung oil had dried? 3) Do you recommend applying tung oil finish to the bottom of the stump/slab? I was under the impression that it needed breathe and should leave the bottom alone. Yes? No? Depend on the wood? 4) Any opinions…
-
-
- 6 replies
- 3k views
-
-
What west system hardener is the best to use to stabilize bad spots in the wood when the finish is going to be clear. Walnut is the wood species
-
- 5 replies
- 2.9k views
-
-
Hello, This is somewhat embarrassing, but I have a hall table that I built a little over a year ago that I started finishing and never completed. Using Marc's simple varnish process, I applied three coats of Arm-R-Seal gloss over an eight day period and then life got in the way. I never put the last coat on which I'd like to be a semi-gloss. This is the first project I've ever built and attempted to finish. So my question is, can I just pick up from where I left off or do I need to take some other steps prior to applying the last coat? Thanks in advance for your advice. --Joel
-
- 5 replies
- 3.1k views
-
-
I'm as new to spraying. I've done wipe on just about everything. I bought a mini mite 3 g-xpc, and I've got some general finishes polyacrylic. GF says their finish is ready to spray out of the container. Has anyone used it and can talk about their experience with it?
-
-
- 8 replies
- 3k views
-
-
I just scored 10 - 90+ year old pine/fir doors. Most of them are covered with I don't know how much paint in every color of the rainbow. Can anyone recommend a good paint stripper or a process that will work, without destroying the wood and taking forever to do. These all came from a townhouse in Washington DC that is being renovated. I should be getting about 10 more doors soon plus any real 2x4's and any other workable material that they pull out. Thanks for the help.
-
- 7 replies
- 3.3k views
-
-
Hello folks, I recently inherited this project that involves stripping and oiling large mahogany panels, then turning them into booth ends for a restaurant. If you look at the picture you'll see the panel on the left is pristine - I stripped that down with the Speed Heater and sanded with my Festool system. It worked like a charm. The panel on the right was chemically stripped by the guy who handed off the job, and as you can see the results were bad and now this discrepancy is my problem. A portion of each panel will never be seen so I have some wiggle room to play around with various methods. Sanding didn't work so it seems chemicals are my only option now. I ex…
-
- 1 reply
- 2.8k views
-
-
I am in the process of making a couple of end tables for our family room and my wife came out to check on me/the tables. while standing there she brought up something that I hadn't really thought of at this point but it is definitely a valid concern. She mentioned that the four grand kids and at times their parents struggle with the concept of coasters. Keeping track of all the cans, bottles and cups during family get togethers can be like trying to herd cats. She was wondering and now has me wondering if there is a finish that will stand up well to the lack coasters and the moister of cups and cans being set directly on the surface. Preferably a water borne product.
-
- 5 replies
- 2.7k views
-
-
All, I am a huge fan of the Greene and Greene style and I've tried several times to use the technique the I've seen described by Darrell Peart on multiple occasions. 7 parts General Finishes orange dye stain mixed with 4 parts medium brown. The probably is I just can't seem to get consistent results with the water based dye stains. It just seems like there is a lot of room for error with the reactivation of the water based stain, the stain drying to quickly , etc. On top of that I would rather not have to raise the grain and sand again before I apply the stain. Has anyone experimented with oil based stains to get a similar look? What are the cons of using…
-
-
- 15 replies
- 4.5k views
-
-
In the Spring, I am going to start stripping a few layers of paint off a 1927 french door. I believe the door is made of Fir if that matters. I want to get it back to it's original state and stained to match the rest of my woodwork. Few questions for you guys... 1. What is the best stripper to use? I hear Peel Away 7 is good but only seems to come in a gallon. which I think is too much? 2. Will the stripper hurt the glass at all? Do I need to tape it off or anything? 3. After all paint is removed, I will start to stain. Same question as above, will the stain hurt the glass at all? Or can I just take a razor to it like I would with paint. Thank you!!
-
- 7 replies
- 3.3k views
-
-
Hello I am new to the finishes that are safe for animals and humans alike. I am building a Hatcher for my chicken eggs and using Maple Cabinet Grade Plywood to build it. I know I can finish the outside with no issues but I need a finish on the inside that wont have fumes that make my baby chicks sick or die. I also want to use a finish that will be able to handle 100 degree heat with humidity of 50% - 75%, and be able to sanitize it after each hatch. I was told by a few folks that I can use the MinWax Polyacrylic inside with no issues is this true?
-
-
- 2 replies
- 2.9k views
-
-
I just finished up a jewelry box for wife for Valentine's Day. It's maple and padauk. I finished it with spray can lacquer Saturday night was last coat. It looks great but I would love to rub it out. I've never done rubbing out before. I'd like a gloss finish. First question do I have enough time to do this by Friday night?(finish cured long enough). 2nd. What is a simple way to do this?? Sent from my iPhone using Tapatalk
-
- 9 replies
- 3k views
-
-
We use very traditional way for finishing carved wood which is not enough. I have attached the work piece. I am working on technique of finishing which will reach to every depth and corner to give perfect finish. can I use buffing machine ? can anybody suggest any ideas about finishing such carved wood ?
-
-
- 5 replies
- 2.8k views
-
-
I am working on an entertainment center that will be supporting my 60 inch plasma TV. I have already stained it to the desired color using a water based dye, and then a 1lb cut shellac as Marc showed to prevent blotches, followed by a Java gel stain for the appropriate color. My Goal was to apply about 5 coats of a wiping Varnish allowing 24 hours between coats and the last coat to dry 72 hours before setting a 100+lb TV on it. We'll I'm behind on my schedule and will only be able to apply 3 coats with the last coat allowed to dry 36 hours. Do you think that would be enough time for the last coat to harden before applying such a heavy item on it? Any other suggesti…
-
-
- 8 replies
- 2.9k views
-
-
As bob493 recommended in the other red oak thread, I am finishing my exterior door project with the dark brown leather dye. I intend to finish the project with the neural base #4 untinted exterior paint. Does anybody see any issues with this top coat over the dye.
-
- 20 replies
- 10.6k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·