Finishing
2,922 topics in this forum
-
Dear Shannon, Matt, and all whom may dread finishing a project, I recently captured the Seven Stages of Finishing a project. Hopefully this helps you understand and overcome your concerns. Stage One: Anxiety. Do I really have to finish this? I'm Nervous! Stage Two: Bargaining. This stinks, let's talk about it. I'll do anything to get out of this! Stage Three: Frustration. You really don't understand how pointless this is. Why are we even doing this? Stage Four: Anger. If I Yell at this long enough it will just go away! Stage Five: The Release. Calming down. I think we're actually getting somewhere. It is starting to look good…
-
-
- 7 replies
- 3k views
-
-
Anybody have experience with electric spray guns? Any good brands or a waste of time? If I were to get one, I would be spraying anything from poly, shellac, lacquer, and maybe paints. I know the HVLP systems are a good investment but I was just curious about the electric spray guns. I'm not doing fine furniture, but I would like it to spray fairly nice!
-
- 5 replies
- 3k views
-
-
Hi all, I am new to woodworking. I am currently on project #4, which is a hand built Roubo style workbench (decided I needed a good bench if I am going to get into this hobby). What is a good finish for workbenches? Do I want to go with some sort of poly coat? Or stay with a more natural oil/wax finish? Thanks, Quin
-
-
- 16 replies
- 154.2k views
-
-
I'm currently working on a joint commission project building a chiropractic chair from oak. The deal is I build it and the guy whom owns a sawmill provides the wood for a cut of the commission. The wood I have gotten from this guy is actually really nice and I have gotten a lot of board feet for free in the past just because he had it lying around or it was left over from a log a client had. The oak I'm using is white oak and most of it is nice except a few pieces have what I believe are holes from powder post beetles. I know I'm going to get lectured about an infestation, but I know that the beetles are gone or dead inside somewhere! Like an idiot....I decided to fi…
-
- 11 replies
- 12.5k views
-
-
Hello All, I need to get an hvlp turbine setup and wondered what the best gun is. I know that the Apollo 7500 and the Fuji 70 and 75 guns are well thought of, I am looking to spray some latex now but would like some flexibility later. Thanks so much, John
-
- 0 replies
- 3k views
-
-
Mark (and others). I'm wondering if anyone recommends using the Charles Neil blotch control product when using figures / birdseye maple? I am building a table and the wood I've found has a good deal deal of birdseye figure, but also a bit of standard maple in it. I do have some of CN's product already, but given that I would like the birdeye to pop, I wonder whether this is the right thing to do? FYI - I plan on using TansTint Vintage maple dye, unless someone has a better suggestion.
-
-
- 12 replies
- 4.7k views
-
-
I need a very small quantity of a high quality marine varnish. Epifanes should work nicely. Where can I buy a small can cost effectively?
-
- 3 replies
- 5.8k views
-
-
This is the first time I have ever shared a solution with my fellow online community. I uncovered few ideas as I researched this topic prior to beginning the work, so, I resolved to snap some pics and write a post in the hopes that other woodworkers/spray finishing enthusiasts could benefit from my experience in this situation. Faced with the challenge of spraying three 16’ long sections of both chair rail and base board, I needed a way to hold the boards off the ground (to avoid introducing contaminants and working on my knees), and at a slight angle from 90 degrees (to ensure stability, and avoid the inconsistent finish that results from a starved, sputtering cup g…
-
- 3 replies
- 2.9k views
-
-
Hello all, First of all let me start by saying I am a complete woodworking idiot. I can barely hammer a nail in but it is something I have always wanted to do so after recently being forced to retire due to a disability I have decided to try my hand at it. So whats the first thing I build? A workbench of course. It is an ugly frankestein but functional workbench that unfortunately at this time has to stay outside in the elements. It is made from 2x4's with two pieces of 3/4 inch plywood glued and screwed together. I then put on a healthy coat of spar urethane. Soooo to finally get to my questions.... 1. How durable is the spar urethane against the elements? 2. D…
-
- 16 replies
- 3.6k views
-
-
I'm trying to figure out how to stain an elaborate easel I'm building (ash stock). Using a wipe off stain would be a problem because of all the nooks and crannies. The final finish will be solvent-based lacquer sealer and lacquer. I have a traditional siphon feed spray gun/compressor, and have an Earlex 5500 HVLP rig on order. What's the best way to get this done? Could I add powder dye to lacquer thinner? Could I spray oil base stain without wiping it off? Do I have to go to water based stain? Whose on first? Thanks for any input!
-
- 2 replies
- 3.1k views
-
-
My typical topcoat is general high performance poly. I spray with an earlex, and I like the results I usually achieve. I am tempted to try lacquer, mainly from the projects I have seen Marc use it on. It looks great, and I like the idea of one coat "burning" into the next. So, where do I start? Is water based lacquer good? Or only solvent based? Which brands do you guys use? Any advice for a newbie to lacquer (besides where a good respirator)?
-
I am about to start a few projects in cherry, and really like the look it takes on after a coat of oil then sitting in the sun for a bit. Previously they have been small project and I would wipe on shellac or Arm-R-Seal. Now I am setup for spraying (nothing special just a HVLP gun and compressor), and picked up a can of Enduro-Var since based on reviews it seems to replicate the look of Arm-R-Seal quite well. I could still go buy some arm-r-seal, and wipe that on, but one project has a lot of slats, and I figured it would be easier to spray. Looking at the GF website it says that while you can use Enduro-Var over oil-based stains it should not be used over linseed …
-
- 1 reply
- 3.7k views
-
-
Hello all, I am making plates for a restaurant. These plates will be used to hold hot cast iron skillets. Is there some kind of clear coat finish that can stand up to that kind of heat? Thanks, Steve
-
- 5 replies
- 3.6k views
-
-
Good morning everyone, I am spraying our oak bathroom vanity white. I have used a primer that will stick to the poly that was on the oak cabinets. I have applied 3 coats of primer. I will be applying the white topcoat today. My question, I would like a top coat that is going to protect the paint. I have used poly in the past but it yellowed.. Is there anything I can put on top? lacquer?
-
- 7 replies
- 18.8k views
-
-
Hello, my husband just finished my farm house bed and we stained it and espresso color, we are wanting/needing to put a finish on top of that we really don't want it to be too shiny is there anything that yall would recommend... Thank you
-
- 1 reply
- 3k views
-
-
I am in the process of rebuilding a shop that used to my great grandfathers (more to come on that later) and I disassembled his old work bench the other night. I have been thinking of ways to reuse the wood from it in a way that will keep me remembering him. He was a great guy. So I was thinking maybe using the top as a head board. Now, a couple questions. I know finishing is going to be a pain because of all the oil, lubricant, and other fluids in-bedded in the wood from 50+ years of being a mechanic. Any ideas on what I can do to keep the color? Maybe poly over everything without removing/sanding anything. Or would I need to strip and sand this before finishing it? …
-
- 7 replies
- 2.8k views
-
-
i have very few of the precat lacquer i used ot finish a kitcehn left and i have 2 more panels to finish (can'T get the original color anymore, i just have what i have left) i have enough for 1 coat only. I was wondering if i could use the post cat lacquer i have in stock, to act as some kind of base coat, sand it, then apply my pre cat lacquer on top for the color. Same brand, same basic chemical composure. i dont see why not, they both cure chemically, the pre cat should adhere to the post cat lacquer hm ? tyvm !
-
-
- 1 reply
- 4.9k views
-
-
Howdy. Planning on building kitchen cabinets in my basement shop. Looking for suggestions of spray finishing them to cut down on time and improve the finish. I was planning on using poly, but not sure what the issues are with spraying. 1. If I do this in the basement I am concerned about the overspray going all over the floor. If I get a small fan and vent out of one of the windows and use a backdrop to spray into with the fan suction at the back of this, OK? 2. I can set up in the garage, but same concerns for overspray. I can build a portable spray booth and set that up. Thanks for any and all help. Brian
-
-
- 4 replies
- 2.9k views
-
-
I have a Fuji MM4 with 1.0, 1.4, and 1.8 tips. The 1.0 tip works great for waterborne topcoats and shellac. I have yet to spray water-based dyes and see that in my future. Since Fuji discontinued the XPC guns I'm wondering if I should get a 0.7mm tip while I can. Are there any benefits to using this over a 1.0mm tip for certain finishes?
-
- 1 reply
- 2.9k views
-
-
I am refinishing an older Van Sciver desk. Made some drawer slide repairs (recreate) Someone else refinished it prior so I'm not ruining an original lol. Anyway, after stripping it down it appears to be Maple, where I thought I was stripping down Mahogany. So, I'm the guy who likes his Maple natural but this desk wouldn't look like with just a clear or tint right? I'm farting with the idea of using Ebony stain on it but need some options. Sent from my iPhone using Tapatalk
-
- 6 replies
- 2.9k views
-
-
Hi guys .... I have a bit of dry paint (water based ) build up on my spray gun in a few awkward places where I can't reach... Is there anything I can use to break it down and flush it out that won't kill my gun ??
-
-
- 8 replies
- 3k views
-
-
I've glued up a couple of pieces of red oak boards and I've got one strip of the light colored sap wood thru it about a quarter inch wide, I will be staining it with minwax golden oak stain , is there a way to match that sapwood to the color of the rest of it before I stain it. or how would you match the sap wood to the rest of the wood?
-
-
- 3 replies
- 2.8k views
-
-
Hi guys, I'm going to "need" to buy an HVLP setup of some kind, but I'm getting confused with what I'm reading online. Are my options: 1-HVLP turbine system, and 2-HVLP Conversion gun and Air compressor? Or does an HVLP gun that's not called "conversion" work with an air compressor???
-
-
- 20 replies
- 6.1k views
-
-
Hello, I am fairly new to staining with anything other than Minwax oil stains. I have used liquid, and gel, with great success on pine. My problem now I that I am building my own kitchen cabinets out of maple, and as expected, its not taking stain well. I have since gone and tried General Finishes stains, and they are still wiping off pretty cleanly, leaving a very minimal stain on the wood itself. I am now looking into dyes, and GF water based stain seems worth a shot. My question is that I have never worked with water based stains, and with my project being kitchen cabinets, are there any durability downfalls with WB dyes? Thanks
-
- 11 replies
- 8.1k views
-
-
Very new to this but I am looking for suggestions on top coat for kitchen cabinets. Cabinets were built from birch plywood with poplar stiles and doors. All wood has been dyed w WDLockwood Dutch Brown (water soluble) but I would appreciate suggestions on what route to take to finish them. Thanks in advance!
-
- 9 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·