Bombarde16 Posted May 1, 2013 Report Posted May 1, 2013 Are there any jobsite/benchtop table saws that are good enough for fine furniture? Much as I love the vast cast iron field of my Ridgid TS3660, I need to do some work in a tiny, basement room and am looking for something small. Most of the small table saws I've seen seem built as disposable chattel for trim carpentry and flooring contractors. A good fence, sturdy height/bevel adjustment and effective dust collection...all in a benchtop size. Too much to ask? Quote
morganew Posted May 1, 2013 Report Posted May 1, 2013 Rob, take a look at a used INCA 259. I know lots of luthier types who use them. They are euro-style where the table tilts instead of the blade. This gives great accuracy in a small footprint. Quote
Eric. Posted May 1, 2013 Report Posted May 1, 2013 How about a TS55 and MFT? Costly, yes, but at least you won't be buying duplicate tools...and the DC will be better if not making a mess is important. How often will you use the extra table saw after this job is done? Quote
wdwerker Posted May 1, 2013 Report Posted May 1, 2013 I have a Makita portable table saw. I put a high quality blade on it and get pretty good results. But in the end it is a skil saw upside down in a nice housing. An aftermarket "t" square fence and table/folding stand did help with the accuracy. It is quite a few years old so I have no idea about the current models. Seems like the saw, stand and blade was more than $500. Quote
Tpt life Posted May 1, 2013 Report Posted May 1, 2013 I also used a Makita 7.25 in the field for years. If the blade size will cut your stock I can vouch for the saw. Quote
bobcrosley Posted May 1, 2013 Report Posted May 1, 2013 I have a friend who is a high-end custom cabinet maker. He uses a TS55 and this Dewalt on the job site. He really likes this Dewalt. http://www.dewalt.com/tools/machinery-portable-table-saws-dw745_2.aspx I think he purchased it from CPO Power Tools: http://www.cpopowertools.com/dewalt-dw745-10-in-compact-jobsite-table-saw/dewndw745,default,pd.html?start=1&cgid=dewalt-benchtop-table-saws If you can get a good price on it, you might be able to recoup much of it when the job is done. Quote
adambaum Posted May 1, 2013 Report Posted May 1, 2013 This is a question for the ages... A follow on question is: are you good enough to work with this type of saw? While the quality of these saws may not be cabinet saw level, as long as you can cut straight, you should be good to go. However, confidence and skill level may impact your output. I had a Jet SuperSaw with sliding table. Great saw, but This version lacked a left mitre slot and I found it hampered my output. Why? Because I was a beginner and just about every video/book showed jigs designed for the left slot or needing both slots. As such, I spent way too much time trying to adapt jigs than i did actual woodworking. Killed my confidence. I moved to a saw with both mitre slots and my confidence, skill, output improved immediately. Adam 1 Quote
chopnhack Posted May 1, 2013 Report Posted May 1, 2013 I had a similar experience Adam. As a newbie first table saw I got was the Ryobi BT3100 table saw system. A great saw that will fulfill all your requirements Rob. It's lightweight and powerful to boot. The current clones as it is no longer produced are the crafstman 21289 Quote
krtwood Posted May 1, 2013 Report Posted May 1, 2013 My dad used to have an old craftsman 9" saw that was direct drive but it had a quiet motor. The table was cast iron but somewhere around 20" deep instead of the standard 27". The motor gave out on it so it's gone now, but I would love to find another one. As much as I like a big table you have to reach so far on crosscuts that when I have a lot of them to do it really gets to my back. I'm not going to put a table saw with a noisy universal motor in my shop. I too wish somebody would put out a really nice smaller saw. Quote
RJsumthn Posted May 2, 2013 Report Posted May 2, 2013 I have this Porter-Cable Jobsite Saw and it does a good job once you put a good blade on it. Quote
Spencer_J Posted May 2, 2013 Report Posted May 2, 2013 this guy got me through 2 years. i made enough money to take my girlfriend and i to south east asia for three weeks with this saw.... the direct drive gears broke and i took it to the metal scrap. I'd probably still be using it if it didn't break. I made a custom router plate to fit in the expanding table section. http://www.homedepot.com/p/Ryobi-10-in-Table-Saw-with-Wheeled-Stand-RTS31/202517812?N=c3x1#.UYG7vo7ENqE dust collection is pretty good, however i added a funnel to the bottom for the dust that didn't make it through the shroud! a builder friend of mine has the bosch most powerful contractor saw... got a zero clearance insert for it and it's very accurate. However, he's got about $900 into it with a rolling stand, cost of the saw and accessories. Quote
Barron Posted May 3, 2013 Report Posted May 3, 2013 Dump the table saw and go with a band saw for rips and a chop saw ( or hand saw) for cross cuts. I love my table saw, but I could live without it. Quote
Juicegoose Posted June 10, 2013 Report Posted June 10, 2013 I couldnt be happier with my bosch 4100. The gravity rise base is great anx it has always been super accurate. 1 Quote
mikem Posted June 10, 2013 Report Posted June 10, 2013 Your higher-end job site saws will get you by for awhile with a good blade installed. I had one for years that I used for all kinds of work. The problem with these saws is that even the high-end ones are plastic bodied with aluminum and plastic components, with fences that are barely adequate. This is definitely not to say great work cannot be done on them. In fact I have seen beautiful work done while using these saws. I was reading some documentation on these saws, I believe in regards to putting flesh sensing technology on these saws, where the average life span of these saws is 5 years. From my experience, this seems right on target even with moderate use. I think if I had to work in a tight space and had to go to a smaller saw, I would seriously be looking at track saw options, especially if this was a long term situation. Quote
Beechwood Chip Posted June 10, 2013 Report Posted June 10, 2013 I also liked my Bosch 4100. I got it refurb for $380. Quote
Darren66 Posted June 10, 2013 Report Posted June 10, 2013 I've got a Makita MLT100, very pleased with it, cuts straight, has handled oak up to it's capacity with supplied blade, , but I wouldn't want to do that often. Only criticism some play in both miter slots and the slots are not standard size. I believe the next model up 2704 may have standard miter slots. But as a newbie it does what I need in my limited garage space. Going to treat it to a new blade soon. Quote
Beechwood Chip Posted June 10, 2013 Report Posted June 10, 2013 Whatever, you get, replace the blade. I had good luck with thin kerf Freud blades, and I agree that a dedicated rip blade helps if you are ripping thicker stock or harder woods. Quote
TRBaker Posted June 11, 2013 Report Posted June 11, 2013 Rob, compared to your cabinet saw, none of these cheapies is going to measure up. I use one on the job site, only when nothing else will do. If it's a big job and I'll be there a while (months), then I mobilize my shop to the job site, table saw, planer, jointer and all. Of course, I don't set up in a basement. Well, in fact, I've never seen a house around here with a basement. Quote
knotscott Posted June 11, 2013 Report Posted June 11, 2013 With a good blade most saws can cut a line straight enough for fine furniture work. The key is making the wood flat and straight prior to putting it on the saw. If you have a jointer and planer any decent jobsite saw should work. Quote
Don Z. Posted June 11, 2013 Report Posted June 11, 2013 Rob, take a look at a used INCA 259. I know lots of luthier types who use them. They are euro-style where the table tilts instead of the blade. This gives great accuracy in a small footprint. First thing that came to my mind... Quote
Freddie Posted June 11, 2013 Report Posted June 11, 2013 For the jobsite saw, the fence and rip capacity is a big one for me. My bosch 4100 works for me in all aspects. It has a nice beefy fence, 25" to the right of the blade, and rolls around the jobsite easy. One thing, make sure the tires are aired up good, on a bigger cut the saw can become spongy. Quote
Milo Posted June 12, 2013 Report Posted June 12, 2013 I have been semi-seriously considering going to a Track Saw. With the new Grizzly being so affordable, and my space being at such a HORRIBLE minimum, I'm getting more and more serious about it every day. I've got my Uni, and Shopsmith 510 w/ Bandsaw, Jointer, Planer, etc. Since I actually HAVE the Uni I am going to wait and see, but if I feel completely cramped I may go in that direction, instead of a smaller, less powerful tablesaw. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.