Tom Cancelleri Posted March 9, 2016 Report Posted March 9, 2016 Yesterday I was in the shop and my 1.5HP single stage dust collector had terrible suction, so I clean it out as best as I could for that moment, and it's a little bit better but it's just not strong enough for my tools anymore. I've wanted to go 2 stage and get a cyclone for a while now. So I am on ClearVue's website with a cyclone in my cart and I decided to check and see if there were any dust collectors on craigslist, just for sh*ts and giggles. There's a CleaVue cyclone on there for $750 with no filters. The guy has a 2 car garage shop, but needs a stronger dust collector. Apparently his shaper with it's two 5" ports while making 7" profiles cant be properly evacuated by the ClearVue. He said he's also like more power for his wide belt, and slider. So I thought ok, so this guy has some serious stuff in a 2 car garage. I emailed him, and the CV1800 is mine if I want to drive 65-70 miles to go pick it up. getting filters will be about 350ish. Thoughts? Quote
estesbubba Posted March 9, 2016 Report Posted March 9, 2016 Sounds like a good deal even without filters. You could even vent it outside and not have to deal with filters. I don't vent mine outside but I've used it over a year and the filter bag barely has any dust in it so you won't be blowing much dust outside. Quote
Tom King Posted March 9, 2016 Report Posted March 9, 2016 5hp single phase. I'm tempted to go get it myself, but won't. That's a nice unit. Quote
mkrusen Posted March 9, 2016 Report Posted March 9, 2016 If you don't get it then please send me the guy's contact info so I can! Seriously though that seems like a pretty good deal. Hope you get it! Quote
Eric. Posted March 9, 2016 Report Posted March 9, 2016 I'd be on that like stink on a monkey. And vent outside, like Mike said. Otherwise it's not quite as juicy of a deal. How much is a new unit with filters? Quote
Tom Cancelleri Posted March 9, 2016 Author Report Posted March 9, 2016 I'd be on that like stink on a monkey. And vent outside, like Mike said. Otherwise it's not quite as juicy of a deal. How much is a new unit with filters? New unit with filters and no bin is about 1700 shipped Sent from my 831C using Tapatalk Quote
AstroDave Posted March 9, 2016 Report Posted March 9, 2016 I paid over 2 grand for mine including filters, clean out port etc... So I say go for it and take it for a spin... Quote
Popular Post toddclippinger Posted March 9, 2016 Popular Post Report Posted March 9, 2016 Looks like a new one without filters at Clear Vue is $1246.50 so there is some savings at $750. Once I went 2 stage on my dust collection, I regretted that I had not done it much sooner. If you vent outside, the only caution is that it creates a negative air flow on the shop and if it shares space with a gas water heater/furnace it can pull exhaust gases back down the chimney. You will have to consider your personal situation for this. If it doesn't have a dust collection barrel, it is likely you can get a heavy plastic barrel for free like I did. One place to look is the furniture refinishing businesses or car washes. The barrels that chemicals come in cannot be disposed of in the landfill. Businesses have to pay for them to be removed and disposed of properly. I got a barrel from one of the local refinishing businesses near me and they tried to get me to take a truckload them. I cut it down to about 29" and added a double layer plywood ring as a handle. The lid just lays flat in place on the handle ring. When the DC runs it sucks the lid tight. The big benefit of the plastic barrel is that it does not get dented over time. I installed a Lexan window in mine and I can easily see when it needs emptied. Good Luck with your decision! 3 Quote
Cliff Posted March 9, 2016 Report Posted March 9, 2016 1 hour ago, toddclippinger said: One place to look is the furniture refinishing businesses or car washes. The barrels that chemicals come in cannot be disposed of in the landfill. Businesses have to pay for them to be removed and disposed of properly. I got a barrel from one of the local refinishing businesses near me and they tried to get me to take a truckload them. Wish I had read that before I spent $80 on a 55-gallon fiber drum from mcmaster.com Quote
socoj2 Posted March 9, 2016 Report Posted March 9, 2016 I bought 2x 55 gallon steel drums with lock lids, *air tight* for $40 =P Quote
Brendon_t Posted March 9, 2016 Report Posted March 9, 2016 1 hour ago, toddclippinger said: I got a barrel from one of the local refinishing businesses near me and they tried to get me to take a truckload them. I had the exact same experience, wanted two for rain't water collection for watering the roses. I asked for two, they said I could have two but had to take 5. I said thanks but I can only store two. They ok come get em. Quote
shaneymack Posted March 9, 2016 Report Posted March 9, 2016 If you vent outside, the only caution is that it creates a negative air flow on the shop and if it shares space with a gas water heater/furnace it can pull exhaust gases back down the chimney. You will have to consider your personal situation for this. This is true Todd, thats why you need a clean air intake if you vent outside. Thats what i did, works great! Sent from my SM-N910W8 using Tapatalk Quote
Tom Cancelleri Posted March 9, 2016 Author Report Posted March 9, 2016 It's got a metal collection pail with it. I'm leaning towards venting outside, trying to figure out the where in the shop part now. Then I need to figure out ducting. Sent from my 831C using Tapatalk Quote
Pwk5017 Posted March 9, 2016 Report Posted March 9, 2016 Agreed, you don't see many clear vues on the used market. I would ding him for gas money and go get it. Im shocked the clearvue doesn't move enough air for two 5" ports. That might be more a factor of ductwork/port size than HP and impeller size. Especially venting outdoors, that thing has to be moving the maximum amount of air at all times. An 8" line would result in more volume capacity than two 5" ports combined. Dunno, doesn't make a whole lot of sense. Arent you the guy who just bought a mm20 for a grand? Where the hell do you live??? Also, what garage fits a widebelt over 15", let alone the power supply to run a 15-30hp sander? A slider takes up a huge footprint too. Something tells me this guy is using the term "garage" loosely, very loosely. Quote
Tom Cancelleri Posted March 9, 2016 Author Report Posted March 9, 2016 1 hour ago, Pwk5017 said: Arent you the guy who just bought a mm20 for a grand? Where the hell do you live??? Also, what garage fits a widebelt over 15", let alone the power supply to run a 15-30hp sander? A slider takes up a huge footprint too. Something tells me this guy is using the term "garage" loosely, very loosely. Yes I am the guy who bought an MM20 for a grand. I live in Northern Virginia. My Craigslist has it's moments where things are freaking awesome. 1 hour ago, Brendon_t said: But it before someone else does. I pick it up Saturday. It's mine. So much for no new tools this year. I'm way past that now. Now I need to run my new sub panel so I can power this beast. Quote
Pwk5017 Posted March 9, 2016 Report Posted March 9, 2016 please tell me how this guy has all these tools in a 2 car garage when you return Saturday. Unless he has a sissy slider and widebelt, I really want to know how he fits both of those in a 2 bay garage along with his shapers, planer, jointer, etc. You need like a 20x25 open space for the 8-10' sliders. I think its a good buy for the product. That baldor motor is good to go for miles, and that cyclone body is bullet proof--literally! or wait, does clear vue use leeson? Quote
Woodenskye Posted March 9, 2016 Report Posted March 9, 2016 42 minutes ago, Tom Cancelleri said: I pick it up Saturday. It's mine. So much for no new tools this year. I'm way past that now. Now I need to run my new sub panel so I can power this beast. Congrats! I am surprised the decision was this difficult! Quote
Tom Cancelleri Posted March 9, 2016 Author Report Posted March 9, 2016 1 minute ago, Pwk5017 said: please tell me how this guy has all these tools in a 2 car garage when you return Saturday. Unless he has a sissy slider and widebelt, I really want to know how he fits both of those in a 2 bay garage along with his shapers, planer, jointer, etc. You need like a 20x25 open space for the 8-10' sliders. I think its a good buy for the product. That baldor motor is good to go for miles, and that cyclone body is bullet proof--literally! or wait, does clear vue use leeson? They use a Leeson Motor. After seeing the google earth of that location, it looks like houses. Quote
Tom King Posted March 9, 2016 Report Posted March 9, 2016 I came back to check. If you hadn't taken it, I was going to. Quote
krtwood Posted March 9, 2016 Report Posted March 9, 2016 Just expect to have to build a wall around it. It's really loud. Probably worse for me because of the concrete walls of the basement. I know people have them in their shops without doing that, Marc for example, but I have no idea how they do it. It was like having a jet engine in the shop. Moves more air with 2 gates open than my 1.5 hp did with 1 gate open though. Quote
shaneymack Posted March 9, 2016 Report Posted March 9, 2016 Its much quieter if you vent outside. Another reason to vent outside. =) Sent from my SM-N910W8 using Tapatalk Quote
wdwerker Posted March 9, 2016 Report Posted March 9, 2016 It will be sucking your heat or air conditioning outside as well. Quote
shaneymack Posted March 10, 2016 Report Posted March 10, 2016 Use mine when its -30c outside. Was never a problem. Im a hobbyist, l never run my dust collector for a long enough time for it to be an issue. The pros far outweigh the cons for me. Sent from my SM-N910W8 using Tapatalk Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.