Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Sculpted Bar Stools

Featured Replies

  • Popular Post

My plan was to make my wife a sculpted rocker for xmas but she decided bar stools for the kitchen counter were a higher priority so here goes...can I get them done by xmas well that we will have to see LOL

First up was to get some lumber. Our kitchen has Hickory cabinets and flooring but since hickory is a pain to work with and I couldn't find any 8/4 stock around here I decided to go with Maple.

 Bar Stool 1.JPG

Should be more than enough for this project and a couple more...

Next up was to transfer all the info onto the templates themselves so I didn't lose it after cutting them out...not sure why this wasn't done in the first place but...

Bar Stool 3.JPG

I glued these to some fiberboard and then cut them out on the bandsaw.

Next up was prepping the seat blanks

Bar stool 5.JPG

Bar stool 6.JPG

Bar stool 9.JPG

Then lay out the seats and cut the joinery. The plans I'm using call for a flat seat unlike the rocker so I made a high fence to cut the joinery using stop blocks to get repeatable results

Bar stool 10.JPG

Bar stool 11.JPGBar stool 12.JPG

Bar stool 13.JPG

Bar stool 14.JPG

Next up was cutting the Maloof joinery

Bar stool 15.JPG

Bar stool 16.JPG

My sculpting tools, I used my $50 rebate to get the RAS 115 :) 

Bar stool 17.JPG

Then I set up outside and went at it using a Triton SuperJaws with a platform I built from 4x4 and 3/4 BB. This worked very well I was impressed with the SuperJaws I had seen Matt Cremona using them on his video's and thought for $140 worth a shot. This makes such a mess I knew I did not want to do it in the shop.

Bar stool 19.JPG

Bar stool 20.JPG

Ran out of sunlight before I could finish so I will have to finish this and the other two on Saturday.

I was pretty much right on the mess...

Bar stool 21.JPG

  • Replies 138
  • Views 38.3k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Well this project is a wrap! here are some glamour shots ...and as requested some situ shots. I really like how they look with the hickory cabinets better then I planned and waaay bette

  • Started sculpting on the backs today ...got creative with my work holding on the fronts After drawing on some guide lines I rough out the curve with a grinder and kutzall wheel I m

  • Thanks Chet! After leveling the legs a bit and final sanding I was able to get the first coat of finish on the stools today. Following Scott Morrison's process of a coat of oil followed by 2 coat

Posted Images

By a flat seat, do you mean not Coopered?

What's the deal with the ras15? I'm not familiar with that green thing. 

 

Nice work so far ! Those templates look like they are from Paul Leminski. Did you order from my fellow Canadian?

26 minutes ago, Brendon_t said:

What's the deal with the ras15? I'm not familiar with that green thing. 

An amazing sander/grinder hybrid. Used more by carpenter than furniture makers but it should do a nice job with the sculpting. I have one and love it. Ive never used it in my shop but will be on my next sculpted pieces. 

  • Author
1 hour ago, TIODS said:

I'm digging this! 

Thanks!

1 hour ago, Llama said:

I like it! 

Thanks! should be fun not something I have done before :) 

1 hour ago, JosephThomas said:

Awesome. Will the seats have low-backs on them?

Yes sir low backs no arms. Depending how this goes I may try a different sculpted design with arms in the future for our basement bar. For my first go around the armless version should make things much simpler. 

1 hour ago, Brendon_t said:

By a flat seat, do you mean not Coopered?

What's the deal with the ras15? I'm not familiar with that green thing. 

 

Correct not coopered.

What Shaneymack said. Using the RAS 115 with 24g sandpaper, CT26, my central dust collection, and air cleaners should allow me to do light sculpting/sanding in my shop with less of a mess then a grinder.

1 hour ago, shaneymack said:

Nice work so far ! Those templates look like they are from Paul Leminski. Did you order from my fellow Canadian? 

I did :) 

47 minutes ago, bleedinblue said:

Awesome!

Thanks!

8 minutes ago, pkinneb said:

I did :) 

I have his rocker plans and recently bought the Maloof chaise lounge templates. I want to build the chaise lounge eventually but wanted a few more sculpted pieces under my belt before i tackle that thing.

  • Author
  • Popular Post
On 11/16/2016 at 8:59 PM, shaneymack said:

I have his rocker plans and recently bought the Maloof chaise lounge templates. I want to build the chaise lounge eventually but wanted a few more sculpted pieces under my belt before i tackle that thing.

I don't remember seeing the lounge I'll have to go check it out.

On 11/16/2016 at 9:02 PM, Bart said:

Looking forward to following this!

Thanks Bart!

 

Well the weather finally worked out so I was able to get the grinding done on all three seats today. I still need to roll the front edges both top and bottom but I can do that in the shop with 24G sandpaper and dust collection. Then a fair amount of sanding. Trying to take the week off so hopefully I can get the legs done this week as well.

Bar Stool 23.JPG

Did I mention what a mess this makes LOL

Bar Stool 24.JPG

Lessons learned regarding power sculpting tools...

If I had to do it again I would go with the Festool RAS115 with 24 grit sandpaper and the Fein corded grinder with the Kutzull Extreme Carving Disc - Medium. These tools both feel good in the hand and have less vibration then the Dewalt grinder. After doing this for several hours I would never use a grinder without a switch, the paddle on my Dewalt really dug into my finger after a while which is why I ordered the Fein (on sale at Klingspor $100). I also purchased a Kutzall original coarse wheel but I felt this wheel was to aggressive and caused a lot of vibration. I also was not at all impressed with the Makita cordless grinder it just went through batteries way to quick like a couple of minutes quick. This surprised me because I have several other cordless tools from them and have always been impressed. Bottom line I currently have a a Makita cordless grinder (tool only), Dewalt grinder and kutzall original course wheel for sale if anybody is interested :) 

Bar stool 25.JPG

Bar stool 26.JPG

Dang! you guys got a lot of snow. I'm so glad that storm missed me we didn't even see flakes in the air.

Thanks for the information on shaping tools. With in the next year i will be making dining room tables and would love to do shaped/sculpted seats so I'll remember this. Did the RAS catch 50% of the dust 75% 25%?

  • Author
16 minutes ago, Chestnut said:

Dang! you guys got a lot of snow. I'm so glad that storm missed me we didn't even see flakes in the air.

Thanks for the information on shaping tools. With in the next year i will be making dining room tables and would love to do shaped/sculpted seats so I'll remember this. Did the RAS catch 50% of the dust 75% 25%?

Yeah we have another 5-8" forecast for tomorrow so I was glad to have a nice sunny day to get this step of the seats done.

I will let you know. So far I have not used it with dust collection since I was outside. From what I have seen in video's it will still sling it pretty good but will catch the fine dust, we shall see. Having said that even without dust collection I would get this it is much more forgiving than the grinder and cuts very well. I still think the grinding wheel for roughing out is good but them switch to this and finish up with regular sander. I also really liked the soft pad Festool sells for their sanders works great on the seat.

55 minutes ago, pkinneb said:

I don't remember seeing the lounge I'll have to go check it out.

I had emailed Paul and he informed me he had the templates but no instructions. He added the templates to the site the next day. My plan is to do the two bubinga sculpted lowbacks that I have in queue and then possibly tackling the chaise lounge.

29 minutes ago, pkinneb said:

I also really liked the soft pad Festool sells for their sanders works great on the seat.

Are you referring to the interface pad?

  • Author
10 minutes ago, shaneymack said:

Are you referring to the interface pad?

Yep

Yep

Yeah its awesome. I used it for the seat also. I was so excited I made a video and put it on YouTube. Lol

Sent from my SM-N910W8 using Tapatalk

  • 6 months later...
  • Author
  • Popular Post

Wow I can't believe its been over six months since I posted to this...anyway between holidays, tax season, vacations, and a new table saw things got away from me. 

After rough cutting the legs I used my big daddy bit and leg template to trim them up.IMG_1889.JPG.d265fdbedab0a4622c85e9ae06c7d6e4.JPG

Next I through a quick jig together to cut the top and bottom joints 90 degrees from what would be the floor as well as the tops of the front legs to 3"

IMG_1890.JPG.70ff083c7e9b118650ccc5a1994f9b41.JPG

IMG_1891.JPG.ba56ee3085871129613afb284328d17b.JPG

IMG_1892.JPG.d3a40c026d86115a038877301258b32d.JPG

Stack of front legs

IMG_1893.JPG.02e7a538f385cdb0a6417bbe541a0910.JPG

Starting to cut the Maloof joints...

IMG_1894.JPG.e4453aee75c97e298874a38e46d922f1.JPG

I think i need to raise the round over bit just a hair what do you all think?

Next up complete the Maloof joints then use a round over bit on most of the parts to cut down on shaping once glued up.

 

You're a patient guy. After six months of inattention, any project would have to be almost done or it would have been cannibalized or burned.

Looking good ! I would definitely try raising the bit a hair to tighten that up as long as that is your test piece. If it an actual leg im not sure id take risk and id do the adjusting by hand.

 

Sent from my SM-N910W8 using Tapatalk

 

 

  • Author
1 hour ago, shaneymack said:

Looking good ! I would definitely try raising the bit a hair to tighten that up as long as that is your test piece. If it an actual leg im not sure id take risk and id do the adjusting by hand.

 

Sent from my SM-N910W8 using Tapatalk

 

 

That's what I'm thinking, thanks! That is the actual leg but I also have a test piece so I'll use it.

These will be cool.  I'm gonna need barstools eventually too and doing them Maloof style interests me.  Do you have an image of what the finished stools will look like?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.