Denette Posted December 24, 2016 Report Posted December 24, 2016 https://vimeo.com/196920663 Anyone else have this problem? When I use my planer, the static from the chips flying through the hose all discharges right into my hands when I'm planing. Anyone ever found a way around this? Quote
Brendon_t Posted December 24, 2016 Report Posted December 24, 2016 Yes, that'll happen on a lot of pipe where chips fly. ground it per the directions. Quote
Sac Posted December 24, 2016 Report Posted December 24, 2016 I have gotten zapped a few times.. But I wouldn't say that it happens on a regular basis. Is it super dry in your shop?Obviously, lack of humidity will make things worse. 1 minute ago, Brendon_t said: Yes, that'll happen on a lot of pipe where chips fly. ground it per the directions. Directions... WTF are those? Pretty sure mine went with the box. Quote
Brendon_t Posted December 24, 2016 Report Posted December 24, 2016 3 minutes ago, Sac said: Directions... WTF are those? Pretty sure mine went with the box. Fair enough. Attach copper wire toward metal on the base. Measure distance to the ground attach other end to a fender washer. Drop fender washer to ground. Bam directions. 1 Quote
davewyo Posted December 24, 2016 Report Posted December 24, 2016 25 minutes ago, Denette said: the static from the chips flying through the hose...discharges Those are wonderful photos! 1 Quote
drzaius Posted December 24, 2016 Report Posted December 24, 2016 I occasionally get zapped from the shop vac hose when the humidity is really low. We connected a machine that grinds the rubber off of old tires in a retread plant. It had a 12" PVC duct to collect the dust & crumb. That pipe was sending out sparks over a foot long. Wrapping it with bare copper wire fixed it. Quote
bleedinblue Posted December 24, 2016 Report Posted December 24, 2016 I was getting shocked from my shop vac hose, so I wrapped it in bare wire, tied a piece of chain to the end and let it drag the floor. Presto. Should work fine on the planer, too. 1 Quote
Just Bob Posted December 24, 2016 Report Posted December 24, 2016 The static from the hose I understand, and a ground wire will solve that. But I don't understand the static coming off the out feed table, what is generating static there? I just finished running a few boards through mine and I couldn't see any reason that the out feed table would generate any static. Is the exhaust hose touching the table? Quote
freedhardwoods Posted December 24, 2016 Report Posted December 24, 2016 The outfeed table isn't generating it. Electricity follows the path of least resistance. You are the ground and the electricity will come to you no matter what part of the hose or machine you touch. If you have a ground wire on the full length of the hose and are still getting shocked, either the wire isn't attached to a good ground or your planer has a serious electrical problem. Quote
Denette Posted December 24, 2016 Author Report Posted December 24, 2016 The static from the hose I understand, and a ground wire will solve that. But I don't understand the static coming off the out feed table, what is generating static there? I just finished running a few boards through mine and I couldn't see any reason that the out feed table would generate any static. Is the exhaust hose touching the table? The hose isn't touching the outfeed table, and there is not a serious electrical problem because everything is fine until I plane wood. My guess is that the friction of the wood sliding against the outfeed table is generating static electricity just like you do if you shuffle across the carpet in socks. There is zero discharge when nothing is going through the machine, whether it is plugged or unplugged, on or off. Quote
freedhardwoods Posted December 24, 2016 Report Posted December 24, 2016 8 minutes ago, Denette said: The hose isn't touching the outfeed table..... The hose is attached to the hood, which is attached to the head, which is attached to the corner posts, which is attached to the bed, which is attached to the outfeed table. Electricity follows the path of least resistance. If it can't ground itself anywhere else, it will go through all those parts to you. 1 Quote
Denette Posted December 24, 2016 Author Report Posted December 24, 2016 The hose is attached to the hood, which is attached to the head, which is attached to the corner posts, which is attached to the bed, which is attached to the outfeed table. Electricity follows the path of least resistance. If it can't ground itself anywhere else, it will go through all those parts to you. Makes sense! May electricity be a lesson to us all. Nature is lazy, so be more natural. Quote
Just Bob Posted December 24, 2016 Report Posted December 24, 2016 27 minutes ago, freedhardwoods said: The hose is attached to the hood, which is attached to the head, which is attached to the corner posts, which is attached to the bed, which is attached to the outfeed table. Electricity follows the path of least resistance. If it can't ground itself anywhere else, it will go through all those parts to you. I agree, except the hose is attached to a PVC exhaust which is attached to more plastic before it goes to metal. I just had mine apart to replace the cutter head and I am having a hard time understanding the path to the outfeed table. I have no doubt its there, I just can't picture it. Quote
Tpt life Posted December 24, 2016 Report Posted December 24, 2016 PVC will conduct high voltage. This is where all the dust collector scare talk comes from. The shop vac hoses are plastic and they will discharge static. What is missed is that the cutter head itself is also likely a generator and it could pass charge through the work piece to the table easily. Quote
Bankstick Posted December 24, 2016 Report Posted December 24, 2016 What Brendan_t said. I did this with my Dust Deputy and Shop Vac. Good idea for the planer. Quote
Marmotjr Posted December 25, 2016 Report Posted December 25, 2016 23 hours ago, bleedinblue said: I was getting shocked from my shop vac hose, so I wrapped it in bare wire, tied a piece of chain to the end and let it drag the floor. Presto. Should work fine on the planer, too. Had to do something similar to our shop vacs when I worked in a sand blasting shop. Really annoying to keep getting zapped while trying to clean up. That all said, if you have grounded the device as described in the manual, and you're still getting an electrical buildup, stop using the planer and call DW immediately. If it's mains power buildup, and not static, this could be a very hazardous situation. Quote
Ronn W Posted December 25, 2016 Report Posted December 25, 2016 I have had the flex hose that attaches to the discharge raise the hair on my arms but no Zap (yet). Quote
gee-dub Posted December 25, 2016 Report Posted December 25, 2016 As freedhardwood stated, all you have to do is provide a better path to ground than your body. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.