Popular Post Ron Swanson Jr. Posted October 6, 2024 Popular Post Report Posted October 6, 2024 I'm pulling for you on this Vonn, hoping that it works out and you get good usable lumber for a song! Maybe i missed it but what is your plan for drying? I might be wrong here but i thought i heard once that for air drying you should expect to wait about 1 year for every inch of thickness. But i don't know if that's accurate or not. 3 Quote
Popular Post wtnhighlander Posted October 6, 2024 Popular Post Report Posted October 6, 2024 I will offer this for consideration: Jay Bates stated his preference for a SYP workbench over one he built from hickory, because the hickory was so hard that it caused excessive rebound from any hammering action, like chisel work. Mark Spagnuolo switched from his original hard maple roubo to one made of cherry, partly because of hardness, but perhaps more because the darker color was better for filming. 4 Quote
Popular Post Beechwood Chip Posted October 7, 2024 Popular Post Report Posted October 7, 2024 On 10/6/2024 at 3:04 PM, wtnhighlander said: Jay Bates stated his preference for a SYP workbench over one he built from hickory, because the hickory was so hard [...] Also, if there's a collision between your project and the workbench, you might want the workbench to dent rather than your project. 3 Quote
Popular Post Von Posted October 7, 2024 Popular Post Report Posted October 7, 2024 On 10/6/2024 at 2:24 PM, Ron Swanson Jr. said: I'm pulling for you on this Vonn, hoping that it works out and you get good usable lumber for a song! Maybe i missed it but what is your plan for drying? I might be wrong here but i thought i heard once that for air drying you should expect to wait about 1 year for every inch of thickness. But i don't know if that's accurate or not. I would love it if I can air dry this wood and I plan to start that way. I've had good experience with air-dried wood - I got a bunch of cherry from my FIL which has issues but is ~75% usable and my friend has successfully air dried a handful of batches, including some hickory. Also, as folks are pointing out, hickory is hard and I believe air drying will help by not making it harder. My understanding is even for kiln drying you want to let the wood dry a little first to shed the loose moisture, especially when it's been harvested during the Summer, as this will have been. I've got indoor space lined up, as well as the stickers and banding and just ordered an inexpensive moisture meter. So, I'm going to stack it and monitor it. As long as it looks good, I'm going to let it dry. If something goes awry, or in a year it's clear it's not going to dry in my lifetime, then plan B. 3 Quote
Ron Swanson Jr. Posted October 7, 2024 Report Posted October 7, 2024 On 10/7/2024 at 7:29 AM, Von said: I would love it if I can air dry this wood and I plan to start that way. I've had good experience with air-dried wood - I got a bunch of cherry from my FIL which has issues but is ~75% usable and my friend has successfully air dried a handful of batches, including some hickory. Also, as folks are pointing out, hickory is hard and I believe air drying will help by not making it harder. My understanding is even for kiln drying you want to let the wood dry a little first to shed the loose moisture, especially when it's been harvested during the Summer, as this will have been. I've got indoor space lined up, as well as the stickers and banding and just ordered an inexpensive moisture meter. So, I'm going to stack it and monitor it. As long as it looks good, I'm going to let it dry. If something goes awry, or in a year it's clear it's not going to dry in my lifetime, then plan B. Sounds like a good solid approach. Godspeed! 1 Quote
Popular Post pkinneb Posted October 11, 2024 Popular Post Report Posted October 11, 2024 Finished up my new steam box and cart. I needed a longer one to steam bend some back loops for some upcoming Windsor chairs. This was based off a Brian Boggs design in Fine Woodworking Magazine. Here is a pic of the chairs I will be making 12 Quote
Ronn W Posted October 11, 2024 Report Posted October 11, 2024 hOpe the steamer meets expectations. Your chair should be beautiful. 1 1 Quote
Popular Post gee-dub Posted October 12, 2024 Popular Post Report Posted October 12, 2024 Cut a dozen mortises today and fitted the tenons. This headboard is going to be a challenging glue up. I am working on some blocking and other "helpers" to allow me to get through the process successfully. 5 Quote
Popular Post legenddc Posted October 12, 2024 Popular Post Report Posted October 12, 2024 Sat in a Windsor chair today when we toured Mount Vernon. I think I’ll have to add it to my list of things to build one day. Bunch of pictures from the tour below. The banister is supposedly a walnut banister that’s older then they United States of America. 8 Quote
Mark J Posted October 13, 2024 Report Posted October 13, 2024 I've been a couple of times, but years ago. Love that place. 1 Quote
Popular Post Botch Posted October 13, 2024 Popular Post Report Posted October 13, 2024 When Frank Klauze "retired" he built his final shop in one of those round barns, really a cool "retirement" shop! There's a good EweTube video of it. 3 Quote
Popular Post legenddc Posted October 14, 2024 Popular Post Report Posted October 14, 2024 It was a very cool experience and I'm glad we went when we did as they're closing a lot of the interior for renovations until sometime in 2026. Going to Montpelier and Monticello are definitely on the list to visit now as well. My daughter is learning about Virginia history this year so she seems fairly engaged when we go. Had an extremely busy weekend. Only have the next two weekends with volleyball and basketball on Sundays and two more soccer games. Then we're down to just dance twice a week until The Nutcracker in December. Ready for a break and having some energy to go into the shop. Hoping work slows down some too after next week. 3 Quote
Popular Post legenddc Posted October 16, 2024 Popular Post Report Posted October 16, 2024 Went over to my parents house today while my daughter was in dance class and loaded up a TV their neighbor asked them to give away. I was going to plane down their laundry room door that won’t shut but realized the hinge wasn’t tight to the frame. Had to take the door off and glued in some dowels. Will go back Thursday to finish it. I did plane two other doors so they close without any rubbing. Have to fix their bedroom door handle if my dad buys one. 4 Quote
Popular Post Tom King Posted October 16, 2024 Popular Post Report Posted October 16, 2024 Not just today, but for probably close to a month I've been working on cleaning the bottom of the sandy cove swimming area. I have the whole thing down to bare sand but for some stuff that can be pumped off. I ran the pump for a little while today but it was barely moving any water. I thought maybe the impeller was worn out from pumping so much sand through it. Turns out the sand had only cleaned everything in it really well except for some Hickory nuts wedged in between the impeller blades. It was pretty easy to take apart with just four bolts holding it all together and was an easy fix. I got tired of fighting it today though, so will wait until another day to pump the remaining silt off. We had a wind blowing straight into the beach yesterday and it helped a lot by pushing everything left up close to shore in shallow water. Every wave leaves a little bit more of the junk on shore. I ordered another intake strainer with smaller holes. 6 Quote
Popular Post Von Posted October 21, 2024 Popular Post Report Posted October 21, 2024 Came across this wooden workbench in our county history museum over the weekend. The sign says it's from the early 1800s and was used for metal working for 150 years. 7 Quote
Popular Post wtnhighlander Posted October 21, 2024 Popular Post Report Posted October 21, 2024 Yesterday, actually. I started replacing one of the webbed cast iron extension wings on my tablesaw with a solid panel of some seriously dense plastic I had kicking around. The stuff is heavier than MDF by a goodly margin. I needed a bracket of 2" steel angle. Although working metal makes a serious mess in my wood shop, it is nice to see that skills I learned on wood will carry over with a hacksaw and file. 7 Quote
Popular Post gee-dub Posted October 22, 2024 Popular Post Report Posted October 22, 2024 I have no trees on the property. I have many low-water plants (we are in a desert basin, cacti and flowering succulents are plants to us). Some drop a few flowers. I live where there is a lot of wind this time of year (and a breeze near-constantly year long). A few days ago we had a bit of a blow for about 12 hours and ALL the neighbors tree leaves found there way to MY back and side yard patios . I have a handy-dandy plug-in blower / leaf vac and wandered around for an hour or so sucking up leaves. I then use the blower to chase the remains of the day out toward the rear of the property. This is what I am doing instead of working on the headboard !?! Grrrr 6 Quote
Popular Post legenddc Posted October 23, 2024 Popular Post Report Posted October 23, 2024 Flew yesterday to Minneapolis for an event I ran today. Got off to a rough start this morning but it ended up going well. Headed out to dinner with some coworkers here soon and then flying home tomorrow. Have a busy Friday and weekend but I think work will slow down now and I can get back into the shop. Looking forward to taking some days off and progress made on this never-ending bookshelf. 5 Quote
Popular Post pkinneb Posted October 24, 2024 Popular Post Report Posted October 24, 2024 Actually over the last few days but... Knocked out some Windsor chair tools. First a drill guide that supports the drill bit while reshaping for better performance (longer point) and cleaner exit holes where backing is not doable like on a bent bow etc. Used the shaper to engrave the tool rest angles so I don't have to look it up every time Next I made a couple of laser holders which will allow me to adjust with out multiple shims when drilling leg holes etc Finally I knocked out another unfinished project on the list I am working through, a chip carved cribbage board. Two down one to go...BTW I have determined chip carving is not my thing so once the last one is complete this week I will have a really nice set of chip carving tools for sale if anyone is interested 9 Quote
Ron Swanson Jr. Posted October 24, 2024 Report Posted October 24, 2024 Wow!!! That cribbage board is beautiful!!! 1 1 Quote
BillyJack Posted October 24, 2024 Report Posted October 24, 2024 Spending a lot of time on line trying to figure out if my bar products are too old. Takes a lot of time. Quote
Mark J Posted October 24, 2024 Report Posted October 24, 2024 4 hours ago, BillyJack said: Spending a lot of time on line trying to figure out if my bar products are too old. Takes a lot of time. "bar products"? Like epoxy, or like liquor? Quote
BillyJack Posted October 24, 2024 Report Posted October 24, 2024 On 10/24/2024 at 1:47 PM, Mark J said: "bar products"? Like epoxy, or like liquor? Only the drinkable kind. Figure if I get my bar back up in working order , I might want to finish it.. 1 Quote
Popular Post Tom King Posted October 24, 2024 Popular Post Report Posted October 24, 2024 There are an endless number of projects here. Some I have to catch the conditions right for. The lake has been low for a couple of days, so I've worked on this section of shoreline between the dock and the first big rock. I guess it's about a hundred feet long or a little more. I want to get all the part in the swimming part of the cove so I can cut the grass right to the water with the mower. This section has been too steep and with exposed rip-rap with various water weeds growing in it. I moved all the stones to build that little jetty, except for a few you can see in the picture that I just dug up today. I've been pulling the dead water weed roots up and building up the hollowed out part where the rip-rap was. I'll top dress that with some screened dirt and plant Rye grass on it as soon as the weather cools off a little more, to hold it over the Winter. All that bare dirt looking fill is full of dead weed roots that I hope will help hold it in place until the grass takes hold. 5 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.