Recommended Posts

Posted
On 3/19/2025 at 7:12 PM, JohnG said:

Another beautiful delivery day!

20250318_153328.thumb.jpg.95a828043f9ca71d8c6627402e574168.jpg

20250318_192128.thumb.jpg.ab651fa55abb40cb92fe323cd9a9b154.jpg

Nice!! Please let me know what you think after you have had a chance to use it a few times. I have been looking at one of these for a while.

  • Like 1
Posted
On 3/19/2025 at 8:58 PM, wtnhighlander said:

Got to watch video of some yahoos attempting to ransack my truck in the driveway overnight. Fortunately, one of them noticed my security cameras, and they ran off before any damage was done.

WTH is wrong with people!! It is nice that cameras are readily available to help deter some of this nonsense.

 

  • Like 2
Posted

I built a little nine lot waterfront development in 1999 and rented a 35 hp chipper along with a Bobcat with 4-n-1 bucket.  We pulled up all the underbrush with the Bobcat, fed it through the chipper and just blew the chips back out in the woods.  The whole place looked like a park when we finished with it. 

I had to sharpen the blades twice doing that.  I think just like any woodworking cutter, sharp works much better.

I don't think your hp will be a problem with sharp blades and not getting too greedy with size of material fed into it.  The one I rented had a self feed, which was nice but pretty scary.

I think I paid 3500 to rent that one for two months, but you get to keep yours.

  • Like 2
Posted
On 3/20/2025 at 11:03 AM, Mark J said:

@legenddc, I didn't know Rigid made a jointer.  Any comments on it?

I have the Rigid 6" JP0610 jointer and it's fine.  I bought it used.  I think the JP0610 is a really common inexpensive hobbyist jointer.

I dream about upgrading to a helical head, and of course, wider is always better.  But for me it makes more sense to build a planer sled for anything the 6" jointer can't handle.  I'll probably look at my cash the next time I need to sharpen my jointer blades, and think about the helical head.

  • Like 2
Posted

@Mark J Ridgid has made at least two jointers. There's the gray one you see in my picture and a newer, orange one. They seem basically the same but there is a different model number. 

Mine isn't the best. I bought it used and I should have tested it more first. It's hard to push a board through and it feels like one of those jointers that is aggressive if that makes any sense. I put new blades on it, cleaned/waxed the beds, etc. but it just doesn't seem to want to play nice.

My dad has the newer orange one and it works just fine. I don't believe it's because it's newer, just maybe had an easier life in the past.

Honestly these are all probably the same as every other jointer made during the same time.

Like @Beechwood Chip I've thought about adding a helical head to mine hoping it helps but I think I'd rather get an 8" jointer. I'm in a small (156 sq ft) basement shop down a flight of stairs so an 8" jointer would be difficult to squeeze in.

Ridgid also made a 14" bandsaw that I own and my Craftsman table saw is the twin of the Ridgid R4512 table saw. I'm not a Ridgid fanboy, it's just what I've found used over the years.

Posted

Doesn't appear that HD/Rigid is still selling the jointer, at least in the US (I did find a Canadian website).  I'm in the market in a "someday, maybe" sort of way.  

Interesting side note, I did notice that Rigid has put it's famous oscillating sander on a diet:

https://www.homedepot.com/p/RIDGID-Oscillating-Edge-Belt-Spindle-Sander-R4840/315674228

(I'd post the picture, but I don't know how to copy it from the website).

They still sell the original model.  

Posted

Yes, Ridgid changed the spindle sander and their table saw to be clones of the Delta branded ones. I don't know if they still sell them or their reputation.

I've purchased a few Ridgid tools from https://www.directtoolsoutlet.com/ for very cheap. Haven't bought anything from there in a few years. I think it was around this time 5 years ago when I picked up a refurbished planer and the spindle sander.

Posted
On 3/20/2025 at 7:58 AM, Tom King said:

I built a little nine lot waterfront development in 1999 and rented a 35 hp chipper along with a Bobcat with 4-n-1 bucket.  We pulled up all the underbrush with the Bobcat, fed it through the chipper and just blew the chips back out in the woods.  The whole place looked like a park when we finished with it. 

I had to sharpen the blades twice doing that.  I think just like any woodworking cutter, sharp works much better.

I don't think your hp will be a problem with sharp blades and not getting too greedy with size of material fed into it.  The one I rented had a self feed, which was nice but pretty scary.

I think I paid 3500 to rent that one for two months, but you get to keep yours.

I thought about renting a big one for a week and chipping as much as possible, but we have more pines fall each year and that quickly exceeds the purchase price. This has hydraulic feed. Glad it has a big reverse bar that wraps around the infeed chute. 

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.