Popular Post Cliff Posted June 25, 2017 Popular Post Report Posted June 25, 2017 When I first started my woodworking journey about 2.5 years ago, I went with workbench I thought I could make. I had a circular saw, new table saw and a drill. I had basically zero skill or knowledge. I think this is just before or just after I discovered the Woodtalk podcast and started absorbing information in large quantities through my earholes. This bench is 2x4 and 4x4 with a top that is 2 layers of mdf and 2 layers of plywood. Uses threaded rod to hold it together. It's honestly not bad at all. Served its purpose and helped me understand what I want out of a bench. Obviously this pic is from way back when. Before I had walls, ceiling, lights, and everything else. Obviously a roubo workbench would be pretty nice. I don't do a ton of hand work, but that is something I intend to change. Mostly importantly, I want to be able to hold stuff. It's a big issue for me. Another big issue for me is getting square cuts with my awful table saw. I recognize the MFT as a decent solution to helping me hold work and get square cuts, but it looks small and flimsy to me, and the last thing I needed was another thing to add to my giant mess already. Since I planned to get a SCMS at some point and build a huge station, I knew the only way I could do this was to get rid of my workbench or my assembly table (which itself is probably the worst thing I've ever made.) Finally I decided I'd get rid of both, and just combine them. Once I made that decision a few months ago, I realized that @shaneymack had made something that would fit my purposes quite well and would be the fraction of the cost of a roubo. So this is my journey into ripping off a fellow forum member (with permission.) I had a slightly different plan for mine though. I don't need storage on one side because it's going to be an outfeed table as well. Not easily accessible on the table saw side. But I needed the support, so I made my center divider about 12" in from one side. I also don't foresee using this as a systainer storage area because my miter saw workstation will perform that task. But I would want to store things in there, just not sure if it will be drawers, shelves or what yet. First I made a giant skateboard: I used the Festool OF1400 router with the track to do the dados. In fact I bought these things just to do this because I can't imagine trying to move a 6' x 3' piece of plywood over my contractor saw. Of course since this was the first time I've used this system I made the mistake of using the LR32 guide plate on my first dado - which worked but was wrong. For one, it stops in the holes (duh) and two - no micro-adjust. I had a test piece cut from one of the pieces of plywood for testing. Worked perfectly. I removed the setup and put the correct guide plate on to do the other dados. And then my story goes south. My test piece was from the same piece of plywood as the base. Fit great. The other two sheets - A LOT thicker for some reason. This is the last time I buy plywood from Menards. Lowes plywood was awful too of course, I had already stopped using them. So I had to sand all my pieces to get them to fit in the dados. Most of the base done, and the hickory in the back for the trim. Then I decided that just because I didn't plan to use this for systainer storage, doesn't mean I can't use it for that purpose until I get my other storage built. Then I cut my hickory to rough length and then stickered them as I just picked it up from the saw mill today (seen here pre-stickered) With any luck, Monday my top for the torsion box will be at the cnc shop to get the MFT layout and I can get to work on that when it's back. BTW, for anyone wondering about cost - 3 sheets of plywood - $150 2 sheets of mdf (may need third, not sure) - $50 34 BF of hickory - $101.91 T-Track from LV - $52.40 6 casters - $48 CNC work - $77 So was it cheaper than building a roubo? Yeah. Except I bought 2 55" FT tracks, the OF1400, a set of whiteside plywood bits. I need to buy the dogs for 20mm holes and a set of the clamping elemenTS as well. So I probably didn't save that much, but all these things will be useful in the future on my miter station build, especially if I plan to do LR32 holes. 5 Quote
..Kev Posted June 25, 2017 Report Posted June 25, 2017 Looks like a fun journey Cliff! Great start! Quote
Coop Posted June 25, 2017 Report Posted June 25, 2017 Cliff, several pieces of the hickory look too short. Am I missing something in the design? Quote
Popular Post Cliff Posted June 25, 2017 Author Popular Post Report Posted June 25, 2017 34 minutes ago, K Cooper said: Cliff, several pieces of the hickory look too short. Am I missing something in the design? Whatcha mean? I cut a couple at 78" to laminate to get the 8/4 I need for the front. The others are about 40". Then I have another 9' board up on the rack as well that hasn't been cut. Honestly not yet sure I got enough, but if I don't, I'll go get more - and maybe accidentally buy some of the amazing 8/4 cherry at the saw mill. 4 Quote
Alan G Posted June 25, 2017 Report Posted June 25, 2017 Cliff Well detailed journal so far. Looking forward to following along! Quote
Popular Post Cliff Posted July 22, 2017 Author Popular Post Report Posted July 22, 2017 Holy month long cnc wait, Batman! Tried to progress on this today after finally getting the top, but it's slightly less than 3 billion degrees out. Seriously time to get a/c in the shop. 4 Quote
Mick S Posted July 22, 2017 Report Posted July 22, 2017 I put a/c in my shop this spring. Wow, what a difference it makes. What kind of CNC are you getting? You'll use the heck out of that bench. I made one of Timothy's MFTC tables a few years ago on a CNC and use it much, much more than my classic bench. I made outfeed tables with the 20mm MFT top. 1 Quote
Cliff Posted July 22, 2017 Author Report Posted July 22, 2017 I didn't get a cnc. I had a local cnc shop do the mft top for me. Yeah I got the feeling I'll use this a whole lot more than my last bench. I can't wait! Quote
bushwacked Posted July 26, 2017 Report Posted July 26, 2017 very nice start! sucks on the month long wait though ... that is kinda crazy! Quote
mat60 Posted July 26, 2017 Report Posted July 26, 2017 Looks good Cliff. Your old bench would be great for other things if you have the room. Quote
Popular Post Cliff Posted July 30, 2017 Author Popular Post Report Posted July 30, 2017 Flush trimming this thing resulted in a good bit of mdf dust covering most everything. My automatic garage door broke, so I couldn't open it for fresh air. Ended up wearing a dust mask for a good hour or so after I finished, with the fan blowing out the side door. Oh and someone borrowed my sander and dust collection for small tools or this would have been at least a little cleaner! I'm a little annoyed that I was super stupid and used a hand plane to clean up the end and blew out the corner. I don't think it will wreck anything but makes me want to smack my head into the wall. \\ Very pleased that this thing is reaching a conclusion. Oh and got an a/c in the window finally - just a real bad one, but I'm hoping to make it through this summer and pick up a new one next year. 5 Quote
Popular Post estesbubba Posted July 30, 2017 Popular Post Report Posted July 30, 2017 You should have enough sawdust on your floor to mix with epoxy and fix that corner Bench is looking great! 4 Quote
Cliff Posted July 30, 2017 Author Report Posted July 30, 2017 3 hours ago, estesbubba said: You should have enough sawdust on your floor to mix with epoxy and fix that corner Bench is looking great! Interesting idea. I did not think of that. Quote
Woodenskye Posted July 30, 2017 Report Posted July 30, 2017 Cliff, the bench is looking good! Initially that corner would bother me, until I did something stupid where I would totally forget about it. Quote
Llama Posted July 30, 2017 Report Posted July 30, 2017 Cliff.. I'd put a chamfer around the whole top and see how much blowout you are really left with. 2 Quote
Cliff Posted July 31, 2017 Author Report Posted July 31, 2017 I ended up doing the epoxy. I put so much mdf dust in the mix that it took 5 hours to solidify. Oops. I didn't take any pics of what I did today. But I milled up the hickory for the trim and routed the dado for the t track from LV. Quote
Cliff Posted August 4, 2017 Author Report Posted August 4, 2017 So this week I finally got sick of not going to the shop when I get home from work. Since I am usually the one that cooks, I basically have 30-40 mins between the time I get home and the time I start cooking. Then maybe two hours before bed. So I forced myself to go out and work in that 30-40 mins. It might have been a mistake because I managed to cut 3 out of 4 trim pieces too short. Ranging from 1/16th inch up to a full 1 inch. I don 't have enough hickory to really deal with that and since it's shop stuff I just went right on trucking. But pretty irritating to be so thoroughly stupid. Regardless, I'm getting somewhere. This is seen in it's most flattering angle. I've also discovered that either the holes are not exactly 20mm or the rail dogs and bench dogs I bought from Precision Dogs are too big. It's an EXTREMELY tight fit. So tight that I have to use something to pry them out. 1 Quote
wdwerker Posted August 4, 2017 Report Posted August 4, 2017 Sandpaper, a dowel, some music and a dust mask ! Remember not to sit your beer on the table until you have sealed it up with some sort of finish. 2 Quote
Popular Post Cliff Posted August 12, 2017 Author Popular Post Report Posted August 12, 2017 So this thing has went continually downhill in terms of trim work. I try not to worry about it so much because as long as the top is flat the thing is going to be fine. But it's also the first time I've really done trim work other than a small 5 drawer cabinet (which the trim was a total disaster.) You can see the gap between the mdf and the trim. Like most things I've done, I'm absolutely a second one would go 100 times better. I'm also suffering from "must move fast and get this damn thing done"-itis. You know how well that goes for a project. I've also ran into a serious issue with the brad nailer. It only fires into the hickory once out of every 3-4 tries, which messes up all kind of things when you trying to hold a piece with glue on it one-handed and trying to get the brad nailer to work with the other. So lesson learned, I think i'd predrill and screw then fill the holes with dowel if I did this again. Taped off the track so I can hopefully prevent finish from getting in there. I'm going to use MinWax wipe on. I was going to use Danish Oil but the big box store was out. 5 Quote
shaneymack Posted August 12, 2017 Report Posted August 12, 2017 This is looking awesome Cliff. It looks familiar ! 1 Quote
Alan G Posted August 13, 2017 Report Posted August 13, 2017 Cliff- though it feels like a tough road right now, it is looking great. Once you are done and able to use that table you are going to put all these thoughts behind you. Keep it up. It's looking great! 1 Quote
Cliff Posted August 15, 2017 Author Report Posted August 15, 2017 Taped some sandpaper to my burnisher and started in. Got 25 holes done in about 30 mins. Trying to be careful not to make the fit too loose. Only 137 more holes to go. 1 Quote
Chet Posted August 15, 2017 Report Posted August 15, 2017 Nothing quit like some nice monotonous work. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.