Chestnut Posted November 6, 2016 Report Posted November 6, 2016 I'm torn between option #1 and Option save the curly for later and buy new stock. It would be hard for me to find a curly or birds eye board 14" wide (it's hard for me to find then in any width). I like RichardA's table but he has maple aprons so you might have to change more on your table to make it all tie together as well as his did. Then the question is do you make the bottom shelf match the top but scaled smaller? Quote
Eric. Posted November 6, 2016 Report Posted November 6, 2016 The top on this hall table I built is only 11.5" wide, so it's not as if it can't be done...just adjust the other dimensions accordingly for aesthetics and it'll be fine. Quote
Ronn W Posted November 7, 2016 Author Report Posted November 7, 2016 Thanks for your input about the dimensions of the top. I decided to make the top and shelf each out of one piece. I ended up with 11 7/8". Now to revise my other dimensions and cut lengths. I was really nervous about milling the curly maple so I put new blades in the DW735 and made a sled. I shim the boards with playing cards for the first 2 passses. Sprayed water on the boards surface and let sit for a few minutes. Set the machine to the slower feed rate, set depth of cut to about 1/32". I was delighted to get no significant tearout. Since the first pass worked I just kept going. There are a couple of small areas that are not quite as smooth as the rest but sanding will take care of that. I think I dodged a bullet. I had not planned to do the shelves until last but I needed to know the width. Now I gaet back on track and work on the legs. Should I seal the ends of the shelves since they will be sitting for awhile? They are about 6" longer than final length. Quote
Ronn W Posted November 8, 2016 Author Report Posted November 8, 2016 Not much time today. Cleaned and changed band saw blades. Re-sawed the aprons from the 8/4 stock. Got a little stress relief that will have to be milled out ------ maybe tomorrow after voting. 1 Quote
Popular Post Ronn W Posted November 11, 2016 Author Popular Post Report Posted November 11, 2016 I resawed some of the 8/4 walnut because t hey were thick enough to get to 3/4" thicknesses. This would allow me to save my 4/4 boards for another project. Good theory but.......the would had some stress to relieve and it relieved itself while I was resawing. I took the one with the worst bow and gingerly started working the at the ends of the bow on the jointer. I got the board to the point where I had 1/32" bow in 48". Close enough for a table apron. At that point I was 1/32" under 3/4"....I can live with that. I surface plane the concave side rest of the resawn pieces to assure myself that none would be thinner than the first and then then planed them to thickness at about 25/32." I think I will be OK. The shelf support stretchers that frame across between the long aprons will straighten them out nicely I decided not to let the tops sit around unprotected while I built the legs and frame so I will be putting at least 1 coat of ARM-R-SEAL on them. Edges bevelled and sanded to 150 grit ready for first coat. Inside corners required some chisel work... First coat soaked in pretty fast....maybe 2 coats before I move on to the legs. 4 Quote
Chet Posted November 11, 2016 Report Posted November 11, 2016 looks like you are making some nice progress Ronn. Quote
Coop Posted November 11, 2016 Report Posted November 11, 2016 Ronn, except for the corners, you beveled the edges on the ts? Quote
Brendon_t Posted November 11, 2016 Report Posted November 11, 2016 Sorry to hear about your wood going wonky but I think it's about par for the course. I have never had much luck resawing 8/4 that stay perfectly flat. seems that one or both usually want to dance around a bit after. Quote
Ronn W Posted November 12, 2016 Author Report Posted November 12, 2016 23 hours ago, K Cooper said: Ronn, except for the corners, you beveled the edges on the ts? I though seriously about using the TS for the bevels but the pieces are 44" long and I can only "rip" 36" to do the ends. So, I used the router table for the bevels all around. I was probably taking a risk consider the funky grain in curly maple but I has to tear outs. Slow the RPM down so I could go slow without burning. Quote
Coop Posted November 12, 2016 Report Posted November 12, 2016 I was going to ask for lessons if you did a piece that size on the ts! Your results are to be commended! Quote
Popular Post Ronn W Posted November 28, 2016 Author Popular Post Report Posted November 28, 2016 OK. I am back on this project. Task for today was to layout and cut leg mortises and to start on "twisting" the legs. Layout the mortise ends and center lines. I used my front vise, some scrap wood and clamps as a jig - 16 identical mortises (8 right hand and 8 left hand). Notice 2 pencil marks on bench to for alignment. I use a pointed router bit aligned with the centerline of the mortise to set the router edge guide against the outside face of the vise. Dust collection on the Triton router works very well. 3/8" x 2" long x 3/4" deep mortise in 2 passes. For a 90 degree twist draw a diagonal line from one edge of the face of the leg to the other over the length of the twisted portion (16" in my case). This was a test - one leg mark in white, one in pencil. The white is not a fine of a line but I chose white for visiblity. Mark all 4 faces of each leg. 2 legs twist to the right and 2 twist to the left. Next job is to figure out a way to hold each leg solidly for saw, chisel, rasp, spkehsave and sandpaper work. I made to holders to fit in dog holes on the bench. They were not solid enough and bent as the vise was tightened so I just clamped the ends. Twisting process. Cut slots and use chisel to remove the bulk. Be careful working to close to the lines because of the chisel catches the grain that crosses your line the resulting tear out could ruin the piece. 9G rasp. 13G rasp Round bottom 10" spoke shave. The hardest part of this process is getting the surface to be "flat" across the width of the twist. It soes not have to be perfect to a straight edge but you don't want to see that it is not "flat". I found the 10" spokes have did not give me enought control to work on a twisted surface. So got a tiny ebony spokeshave from Woodcraft. I like it. Sanding will be final step but that will wait until all for sides of the leg are done and I can true up the edges where the sides meet. The edges need should be same dead straight lines that where drawn diagonally on each face. I keep telling myself to slow down because. If the edge is violated it looks like hell real easy. I takes me about an hour to do one side of one leg not counting final trueing and sanding ---Arrrgh - 16 hours. Just glad it is not an octagonal table I will post a couple of pics of the first leg when it is done. I would like to have the legs done before Christmas. 6 Quote
..Kev Posted November 28, 2016 Report Posted November 28, 2016 Looking awesome! Nice detail in the journal! Quote
Eric. Posted November 28, 2016 Report Posted November 28, 2016 I like your style, Ronn. You're doing clean work. Quote
shaneymack Posted November 29, 2016 Report Posted November 29, 2016 Looks really cool, Ron. Nice work! Sent from my SM-N910W8 using Tapatalk Quote
wtnhighlander Posted November 29, 2016 Report Posted November 29, 2016 Thanks for the explanation, Ronn! I want to try this technique some day. Can't wait to see yours finished! Quote
Chet Posted November 29, 2016 Report Posted November 29, 2016 Nice work Ronn and a great journal. Quote
Alan G Posted November 29, 2016 Report Posted November 29, 2016 Great journal! Doing some great work! Quote
Popular Post Ronn W Posted November 29, 2016 Author Popular Post Report Posted November 29, 2016 First twisted leg done, sanded, bare wood. About 6 hours to do the twist. I am getting more efficient, tho, I absolutely love the miniature ebony spoke shave. It is easy to control around the twisted surface. And I finally figured out that multiple passes with a very light touch works the best. 13 Quote
pkinneb Posted November 29, 2016 Report Posted November 29, 2016 I 2nd that WOW really cool thanks for sharing. Quote
Mark J Posted November 29, 2016 Report Posted November 29, 2016 That's really impressive, Ronn. Honestly that looks so good you'd think it was done by some computer operated machine. Quote
drzaius Posted November 29, 2016 Report Posted November 29, 2016 Are you sure you didn't just put one end in a vise & twist with a really big wrench. Looks about perfect. Quote
mat60 Posted November 30, 2016 Report Posted November 30, 2016 Really like your project and the legs look like you spent allot of time with them. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.