Recommended Posts

  • 3 weeks later...
Posted

Test fit all the M&T one at a time.  I was a little disappointed in my myself that so many of the tenons were to tight (adjustable with 80 g sandpaper) and some were  just a little long (adjustable with chisel).  Note to self: "Remember to make the tenons a little shorter than the mortises next time." 

Dry fit table frame and make sure that top of the aprons are at the proper height. Aprons not yet cut to final profile which will be an arch.

Dryfit.JPG

Measure for shelf support cross pieces.

measure.jpg

Note to self: " Please, please remember to put the cross pieces in when I glue up the frame."

Next will be cutting cross pieces to final length, cutting tenons and cutting slots for the shelf attachments. 

Now is the point in the project where I usually start wondering if I have made a serious mistake that I just  haven't discovered yet.  Anyone else ever get that feeling?

  • Like 2
Posted
20 minutes ago, bleedinblue said:

Psh.  Too tight/too long tenons are such a simple fix, no problem.  Better than being too loose!

Amazing work.

Yes, I always want them a bit snug so I can finesse the fit to near perfection.

  • Like 1
Posted

Cutting  aprons and support pieces to shape.  3 templates required. I make my templates by printing out the shape on my large format printer (24x36" sheets) and using spray glue to attach to MDF or plywood. Long aprons - since these are 41" long so I made a 1/2 template. Short aprons.  Cross pieces that support the shelves.

Band saw and then spindle sander or spoke shave.P1010002 (4).JPGP1010006 (3).JPG

 

Then its double sided tape and on to the router.  I love my combo bit.  When the grain changes, I can flip my piece over and raise or loser the bit to avoid tear out.

P1010005 (2).JPGP1010004 (2).JPG

P1010007 (3).JPGP1010008 (3).JPG

I have been think long and hard about how critical it will be that the tops of the shelf support cross pieces be perfectly in one plane so the shelves sit squarely on them.  Here is my solution.  The bottom of the top shelf will be 1/2" above the top of the legs so I working upside down I have the legs resting on 1/2" pieces of MDF and the cross pieces pressed down tight to the bench top.  I know my bench top is pretty true so that should do it - at least for the top shelf.P1010009 (2).JPGP1010010 (2).JPG

These pics are just a dry fit.  When the time comes I plan assemble all the pieces but only glue the cross pieces to the long aprons to create shelf support assemblies.  Then, separately I will glue the end aprons to the legs to create the end frames. Then glue the end frames to the and the shelf support assemblies together.  I have decided to assemble and glue that bottom shelf support assembly just like the top one shown in the photo.  I should fit nicely into the mortise for the bottom aprons since I am confident that the mortises are accurately positioned.  But I am cautious and will test fit it all first.

I still have not decided how I want to attached the shelves to their supports.  I could always use table 8's, but am also considering, because I have not done it before, a slot in the support pieces and cleats to fit into the slots and screw to the underside of the shelf.

Anyone feel strongly one way or the other?  I'd love to hear your opinion.

Merry Christmas, all!

  • Like 1
Posted

This installment is mostly about the cleats for the shelves.   Decide to go with home made. Something new for me.  Slots first then cleats.Cleat slots 1.JPG

Chisel Cleat Slots.JPG

Cutting cleat dados

Cleat Dados.JPG

Cutting cleats to widthRipping Cleats.JPG

Four 1" wide cleats for tight fit and 4 7/8" wide to movement.

Completed Cleats.JPG

Problem.  When I test fit the cleats into the slots, I found that the top of the cleats were slightly below the the tops of the support pieces.  How to adjust.  I scribe a line to mark the new top of slots location using the dados as a guide.Adjusting Cleats - Copy.JPG

A little chisel work and they now fit.

Cleat fit.JPG

Didn't need to but the cleats needed a finishing touch.

Beveling cleats.JPG

Each cleat is marked for a specific location.  God help me if I lose those markings!!

I decided to apply the first coat of finished before assembly for ease of application.  I applied BLO, rubbing it in with 600G sand paper.  Probably 2 more coats (without sandpaper) after assembly.  Pieces have a pleasing. smooth feel.  That's what I wanted.

First coat Legs (1) - Copy - Copy.JPGFirst Coat sshort aprons.JPG

Now I have a question..........I got a llttle oil on the tenons from my fingers during finishing.  It's not much but I am concerned with the integrity of the glue joints.  Should I use my Titebond III as planned or should I switch to T-88 epoxy??

 

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 54 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined