Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Strange Occassional Table

Featured Replies

  • Popular Post

Here is the new Project.  Table 13" sqaure and 34" high.  Cherry with Curly maple veneer over plywood for the top.  Final dye and or finish to be determined.  I want to do some sample boards of dyes in shellac before I decide.

Table.JPG

I was just going to get 2 boards but when I saw the 11" wide one, (beautiful) I bought that, too.  Will use the wide one for the table and save the 2 narrower ones for future. one narrow board not in the pic

P1010001.JPG

Will cut the veneer from this pice of maple - Will be 1/16" thick after drum sanding.

P1010002.JPG

Planed both sides and rough cut.  Waited a couple of days before final thicknessing.

P1010003.JPG

Aprons cut to length and splines ready to glue.  Thicknessed splines on drum sander. All the rest done on table saw.

P1010004.JPG

Quick test fit.

P1010005.JPG

Rout the bead around the apron.  Beading bit was my new tool for this project.  Every project needs a new tool.

P1010006.JPG

P1010007.JPG

All glued up.  The corners turned out really nice. too bad they will be hidden when corner treatment is added.

P1010008.JPG

More later.

Another tricky leg project, eh? Looking forward to seeing this one.

Sent from my SAMSUNG-SM-G890A using Tapatalk

  • Author
  • Popular Post

Finished the aprons.  Made corners posts.  Each out of 2 pieces.  Created notch in corner for the pieces using table saw and square ground blade (WWII - 40 T - special cut)P1010013.JPGP1010014.JPG

The real challenge on this project to create a jig to allow the routing of the dado for the lower shelves and cutting of the legs at the top, bottom and straight portion of the legs that will be inside the top.

Cut and squared up a piece if MDF and then glued guides/stops to the edges. Pic of just the jig.P1010015.jpg

Then used dado jig the I made based on Marc's video.  Clamped it in place and routed the dados.P1010011.JPGP1010010.JPGP1010012.JPG

Now to use the jig as a sled to make cuts at the table saw.  Realized that I needed to by a couple of mountable holddown clamps.   Installed clamps.  The 3 pencils shown where I need to make straight line cuts.  The chalk lines just show roughly the shape of the legs so you all can see where this is going.

P1010016.JPG

Cut #1.

P1010017.JPG

Cut #2.

P1010019.JPG

Cut #3

P1010020.JPG

Time to cut the curves in the legs at the band saw.  I use a large format pirnter that I used during my engineering days to print out the leg full size and glue it to one of the legs.  That leg will, in turn. be the pattern for the other 3 legs.

P1010021.JPG

Cleaning up the first leg.P1010022.JPG

My spokes have skills are still under construction so used the spindle sander for final smoothing.

P1010023.JPG

Routing the other 3 legs with pattern bit with top and bottom bearings allows me to route with the grain.

Pattern on top.

P1010025.JPG

Pattern on the bottom

P1010024.JPG

Now to sand the legs.  Nest step will be the table top.

I do have a question....... Two of the bottom shelf to leg dado joints will be end grain. Will epoxy glue create a stronger end grain to cross grain glue joint than Tite Bond yellow glue?? 

 

 

P1010018.JPG

P1010024.JPG

  • Author
  • Popular Post

I could not resist a test fit and a preview of what it would look like.

P1010026.JPGP1010027.JPGP1010028.JPG

Just noticed that the apron is upside down.  Glad it's just a dry fit.

Thinking through the gluing process for the top.

P1010029.JPG

Placing 1/16" veneer only plywood for top.  Using contact cement.  Resawing  a 10" piece of maple was about as much as my Laguna 14 twelve could handle.  Now waiting for the glue to dry.

P1010030.JPG

Wow Ronn, this is really something to follow, great progress and skilled work on all aspects of this piece.

That looks really great! Can't wait to see it all finished!

Sent from my iPhone using Tapatalk Pro

On 2/1/2017 at 5:24 PM, Ronn W said:

 I do have a question....... Two of the bottom shelf to leg dado joints will be end grain. Will epoxy glue create a stronger end grain to cross grain glue joint than Tite Bond yellow glue?? 

Pure speculation here, but I would think the answer is yes. Since epoxy acts as a gap filler, I would think it would do a better job of bridging the gap between the joints once it gets sucked into the end grain. I read something from a polyurethane glue manufacturer that claimed that it was far stronger than yellow glue in end grain glue ups for just that reason. Seems like epoxy would be similar.  

My simple minded brain has trouble even following your work on this.  

 

That is a really neat project and once again my mind is blown what some people can do with wood, one day for me.....  Thanks so much for sharing!

Lovin' it.  Even though I know what I'm looking at and what to expect, it makes me do a double take.

  • Author

If the final geometry is what I hope, the legs will fit square in the corners of the apron and can be glued.

  • Author
  • Popular Post

Final gluing of the legs.  Each leg glued to both aprons with Tite bond Original.  Should be enough - lots of surface area.  Forgot to take pics of inserting shelf in dados but they fit.  Used epoxy glue for that since 2 of the 4 dado joints are end grain.

P1010031.JPG

Glue the top together one side at a time.  In each case I still clamped all 4 sides in place so I could be sure the miters stayed tight.  I started out planning ot glue 2 (opposite) sides at a time but fitting a piece with a miter on each end has to be perfect and the when you have to move the piece around the glue tens to set faster.  The sides are spline to the center and the miter are spline.  Alignment was pretty good -- just a little sanding required.  Note to self, "If the spines are even a little snug during the dry fit, they are too tight for much adjustment once the glue is added."P1010032.JPG

Sorry about the focus on this one.  Ready for finishing.

P1010033.JPG

Sample boards.  Want to get a fair contrast between the cherry and maple but minimal yellowing.  Samples not done yet.

1. BLO, WB poly, WB POly

2.  3 coats ARM-R-Seal

3. Shellac, shellac, WB ploy

P1010034.JPG

We're in the home stretch.

  • Author
  • Popular Post

OK. Last entry for this project.  Finish is 2 coats clear shellac and 1 coat GF-WB High performance top coat except 2 coats on the top because I missed a spot. A few pics.......P1010035.JPGP1010036.JPGP1010037.JPGP1010038.JPGP1010039.JPG

Not only cool looking Ronn, but great craftsmanship! 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.