Ronn W Posted January 28, 2020 Report Posted January 28, 2020 I have had an "Avenger" Dado set foryears. Did not used it much = always thought is was a pain to set up. It was difficult to get even a single blade on the arbor HOles were rough or undersized) let alone the whole stack. My current project needs 13/16" dado in a single pass which uses all the blades and leaves just enough room for the nut arbor nut. I installed my set and, 3 times that nut came loose during test runs. It now has chipped carbide teeth and is probably not safe to use. Any recommendations on a good quality dado set that can get me 13/16 width? Any other comments on proper use of a dado stack would also be welcome. Quote
Chet Posted January 28, 2020 Report Posted January 28, 2020 I have, and like the Freud Super Dado, Model # SD508. I have had it about 5 years now and it has held up real well. I haven't even had it sharpened in that time, just keep it clean, but it is getting close. I like the chipper having 4 teeth instead of two, I think it helps give a cleaner cut but I have nothing scientific to prove that. Quote
Chestnut Posted January 28, 2020 Report Posted January 28, 2020 I have the cheaper Freud SD208 and am happy with it's performance. Quote
pkinneb Posted January 28, 2020 Report Posted January 28, 2020 1 hour ago, Chet said: I have, and like the Freud Super Dado, Model # SD508. I have had it about 5 years now and it has held up real well. I haven't even had it sharpened in that time, just keep it clean, but it is getting close. I like the chipper having 4 teeth instead of two, I think it helps give a cleaner cut but I have nothing scientific to prove that. X2 i've had mine for a long time and its been sharpened at least twice maybe 3 times. Very happy with it. Quote
B1rdhunter Posted January 28, 2020 Report Posted January 28, 2020 I have the Dewalt Dado set and really think it does a good job. Quote
curlyoak Posted January 28, 2020 Report Posted January 28, 2020 I have a Freud also. 8" x 13/16 It is 40 something years old. Been sharpened a few times. Still going. Quote
wtnhighlander Posted January 29, 2020 Report Posted January 29, 2020 My saw claims to support 13/16" on the arbor, but I'm too chicken to try. If your arbor nut is coming loose, there must not be a full thread engaged. Mine tightens against the blade spin, so that I can get away with barely more than finger tight installation. Quote
Coop Posted January 29, 2020 Report Posted January 29, 2020 Back off on the chipper blades and make two passes. 2 Quote
Popular Post Ronn W Posted January 29, 2020 Author Popular Post Report Posted January 29, 2020 Thank you all for your input. I stopped b y Rockler and bought the Freud SD208. I j ust don't use it often enought to justify the more expensive model. It looks kinda scary sitting on the arbor since my old set had many more teeth on the chippers so that it looked more solid. First thing I noticed is that the spacers and shims are steel and that there was a real solid feel when I tighened the arbor bolt and the blades and chippers did not rotate with the wrench. My old set had aluminum and plastic shims that tended to slip as the bolt was tightened. Also the blades and chipppers slid onto the arbor smoothly. The blades and chippers in the old set were hard to get on and harder to get snug against each other. I fired it up for a few seconds and it didn't explode. Checked the bolt and it was fine. Did one test cut and it cut like butter - 13/16 wide and 1/4" deep in hard maple. I'll cut the dados in the sides of my drawers tomorrow. I am going to sleep happy now. Thanks again. 7 Quote
treeslayer Posted January 31, 2020 Report Posted January 31, 2020 On 1/28/2020 at 11:12 AM, Ronn W said: I installed my set and, 3 times that nut came loose during test runs. First i'm glad you're ok and second i bet that was a very exciting 2 seconds, care to fill us in on what happens when the nut comes off? never had one do that on the TS, i did have a bearing come of a router bit once. Quote
Dave H Posted January 31, 2020 Report Posted January 31, 2020 I have a delta uni-saw it came with 2 different arbor nuts the one for regular saw blades is a nut/washer set up the washer is large in dia. and heavy gauge I'm thinking it is for stabilizing the blade, the other nut has no washer it is to be used for dado stacks. Maybe your set up is the same and you could get a different nut in my area we have a store Tacoma Screw that carries just about any screw or, nut maybe you a similar store in your neck of the woods who could help you get a smaller arbor nut. Quote
RichardA Posted January 31, 2020 Report Posted January 31, 2020 Ronn, do you have a Fastenal store anywhere around you? They can supply a thinner nut, and still allow you to sleep comfortably. Quote
drzaius Posted January 31, 2020 Report Posted January 31, 2020 When using all the chippers the instructions say to leave off the outside washer. That's what I do & have never had a problem. 1 Quote
Ronn W Posted January 31, 2020 Author Report Posted January 31, 2020 2 hours ago, drzaius said: When using all the chippers the instructions say to leave off the outside washer. That's what I do & have never had a problem. I do have to leave the washer off - then I have a couple threads exposed. 4 hours ago, treeslayer said: First i'm glad you're ok and second i bet that was a very exciting 2 seconds, care to fill us in on what happens when the nut comes off? never had one do that on the TS, i did have a bearing come of a router bit once. I do have to leave the washer off - then I have a couple threads exposed. When the nut loosens you hear a grindin sounds - a combination of the arbor spinning faster than the blades and the really scary sound of the blades carbide tips hit each other like a toy machine gun. If you don't shut it off right away, the next sound is the thunk of the nut coming off. I don't want to wait to hear the outside blade coming off. If something does not sound right step to the side and hit the stop switch. No telling if the carbide tips are headed you way. If you have a zero clearance pinsesrt it won't be any more. 1 Quote
BillyJack Posted February 8, 2020 Report Posted February 8, 2020 I just use the nut with the Delta RAS or Unisaw. I've had the Freud blades slip out of alignment after running the saw but nothing critical. ... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.