Power Tools
4,152 topics in this forum
-
- 3 replies
- 1.3k views
-
- 14 replies
- 8.7k views
-
- 23 replies
- 17.3k views
-
- 11 replies
- 2.4k views
-
- 2 replies
- 1.6k views
-
- 13 replies
- 3.7k views
-
- 5 replies
- 1.7k views
-
- 12 replies
- 2.4k views
-
- 35 replies
- 5.5k views
-
- 6 replies
- 1.9k views
-
- 12 replies
- 4.2k views
-
- 18 replies
- 3.8k views
-
- 16 replies
- 9.8k views
-
- 5 replies
- 1.9k views
-
- 6 replies
- 2.3k views
-
- 25 replies
- 29.6k views
-
- 13 replies
- 10.5k views
-
- 23 replies
- 3.4k views
-
- 15 replies
- 10k views
-
- 2 replies
- 7.1k views
-
- 9 replies
- 2.3k views
-
- 17 replies
- 2.8k views
-
- 2 replies
- 2.7k views
-
- 8 replies
- 2.3k views
-
- 9 replies
- 2.2k views
-
Who's Online 2 Members, 0 Anonymous, 57 Guests (See full list)
-
Forum Statistics
31.2k
Total Topics422.2k
Total Posts -
Member Statistics
23,781
Total Members3,644
Most Online
-
Topics
-
-
Posts
-
What type of pipe in the well, and how far down is the pump? You could just put a tee in that flex line to the house. I'd want a stainless union out of that tee, then a couple of ball valves as cutoffs going either direction. https://www.supplyhouse.com/Bluefin-SLU100-T304-1-Stainless-Steel-Union? -
Seems to be a galvanized fitting. I’m fairly certain I’ll need about 3 adapters to get the temporary hookup done, but I’ll figure something out. It doesn’t help that almost nobody puts plumbing fittings back in the correct bin. -
Garden hose threads are different than anything else. Often labeled as 3/4 WH. Ace sells a bunch of different adapters in their brass fittings cabinet. I keep a washing machine hose for emergency hookups as well as various adapters. The washing machine hose is the only short one I know of with female WH ends on both ends. What type of pipe is that faucet screwed onto? Picture would be good. edited: Sometimes GHT for garden hose threads instead of WH for water hose. I see them both ways. Here's an example of the kind of thing you'll need to hook a hose to PVC https://www.amazon.com/Sanpaint-Connector-Garden-Fitting-Adapter/dp/B08FSY4DQT/ref=sr_1_2?
-
My yard hydrant installation was pretty smooth through 95% of the job. Unfortunately I’m stuck for the moment. I got the Y34 placed, ~100ft of PVC run, but then I tried to remove the spigot from the tee at my well head so I could attach the PVC ball valve and tie into my line to the field. It’s been installed for ~30 years and does not want to budge. I pulled out my 36” pipe wrench to assist, but I’m a bit worried that I’ll snap it off before it unscrews. I don’t have much room to tie into my house supply line without a lot of careful digging, so I’d rather not tap off of that. I’m now thinking that in the short term I’ll use a 6-12” piece of 3/4” garden hose to connect my 1” pvc to the spigot. That way I can at least confirm my PVC joints are solid before I fill in the trench.
-
to get a shop full of tools worth while will cost thousands. Unless you had orders for a lot of doors, have them made for a lot less money. If you intend to learn woodworking it might eventually pay off. Unless you loose interest and the tools sit...
-
-
Popular Contributors
-
1
-
2
-
3
-
4
-
5
-
