Just Bob Posted October 21, 2018 Report Posted October 21, 2018 Went to swap out my blade for a dado set this morning and the found the arbor nut frozen. So far I have tried PB blaster, heat from a propane torch, and a breaker bar w/socket. There is not enough room for me to get my impact wrench in the cabinet. So before I tear apart the saw and remove all of the cast iron, any suggestions? I have tried tightening it a smidge then loosen, but no love. Saw is a grizzly G0690 but that shouldn't matter. Had the saw about 8 years, and this is the first trouble I have had. Quote
Tpt life Posted October 21, 2018 Report Posted October 21, 2018 Left hand threads according to the manual. 1 Quote
Spanky Posted October 21, 2018 Report Posted October 21, 2018 When you get it off, put Anti Seize on the nut. Quote
wdwerker Posted October 21, 2018 Report Posted October 21, 2018 Holding the arbor still is key. My UniSaw has flats for a second wrench to hold the shaft still. Didn't come with the wrench, I had to find one on my own. Delta didn't even list one. Quote
Just Bob Posted October 21, 2018 Author Report Posted October 21, 2018 It is a 2 wrench deal and no matter what I do I can't get it loose. So it looks like I will be tearing the saw apart so I can get an impact wrench on it. Crap. Quote
Chestnut Posted October 21, 2018 Report Posted October 21, 2018 Could try a heat gun on the nut. I know mechanics use torches but just the head gun might be enough. 1 Quote
Pondhockey Posted October 21, 2018 Report Posted October 21, 2018 Sorry to repeat, but you're really sure that you are "loosening" in the same direction that the saw blade turns? Quote
Mark J Posted October 21, 2018 Report Posted October 21, 2018 Yeah, that left hand thread thing. Otherwise Liquid Wrench; tap on the nut several times; repeat. Quote
Pondhockey Posted October 21, 2018 Report Posted October 21, 2018 1 minute ago, Mark J said: Yeah, that left hand thread thing. Otherwise Liquid Wrench; tap on the nut several times; repeat. And if there's not an urgency to it, letting it sit overnight. That's frustrating when an unanticipated weirdness stops work cold on a project. Quote
Tom King Posted October 21, 2018 Report Posted October 21, 2018 I have both left, and right tilting table saws. I don't bother to remember which nut turns which way. I always look at the threads. It's a good thing you can use two wrenches. Use real wrenches that are the correct size-not some stamped wrenches that might have come with the saw. If hands can't free it with real wrenches, pipes on the wrenches surely will add enough leverage. Don't strain, use more leverage. Strain raises the chance of injury exponentially. Quote
wdwerker Posted October 21, 2018 Report Posted October 21, 2018 You can put a block of wood against the blade and loosening the nut always is the wrench pulling toward the board. Holding 2 wrenches try whacking straight down on the arbor wrench with a hammer as you squeeze the 2 wrenches together. 1 Quote
Popular Post mat60 Posted October 21, 2018 Popular Post Report Posted October 21, 2018 Im thinking you guys have had your nuts seized a time or to also. 3 1 Quote
wdwerker Posted October 21, 2018 Report Posted October 21, 2018 Thus we know how to help our fellow man out ! Not a situation to leave a guy hanging in. 1 Quote
Just Bob Posted October 22, 2018 Author Report Posted October 22, 2018 I appreciate the encouragement! Yea I know it is a left hand thread, double, triple checked that it wasn't stupid Sunday. I have soaked it in PB blaster, heated it with a torch, used my breaker bar on it, with and without a wood jam, no matter what, I am stuck with stripping the top off, so I can get an impact wrench on it. I have a cabinet I have to finish before I start, using a router to cut to grooves I was going to use the table for. Lot more setup, but I am almost done, then I will start taking the saw apart. Quote
Tpt life Posted October 22, 2018 Report Posted October 22, 2018 I don’t use PB as often since I tried Liquid Wrench’s version. Either way, I soak an walk away for a few hours. If that does not work and I move to a torch, I let wax wick in during the heat cycle. I will cycle up and down several times applying wax each time it is hot. Quote
Coop Posted October 22, 2018 Report Posted October 22, 2018 Sounds like a dedicated rip, crosscut saw until the blade needs sharpening/replacing. Good luck bud! Quote
Popular Post Just Bob Posted October 24, 2018 Author Popular Post Report Posted October 24, 2018 Took the saw apart and once I had the cast iron off was able to use my impact wrench and the nut came right off. Didn't see any damage to the arbor, so I went to Grizzly and bought a new arbor nut. Cleaned up the saw, it is amazing the amount of stuff that stays inside a table saw. Tightened the belt, lubed the trunnion and got it all back together this morning. (Yes I used anti-seize this time.) Side note: While I at Grizzly (Bellingham, WA) store, I saw that they were setting up a Festool display. I asked and they told me that they signed a contract with Festool 2 weeks ago, and in addition to Festool, they will also be selling SawStop. I found that interesting. 3 1 Quote
..Kev Posted October 24, 2018 Report Posted October 24, 2018 Good to hear on the saw! Interesting to hear on Grizz! I assume that Windsor is still doing FT? They're really close to each other! Quote
Just Bob Posted October 24, 2018 Author Report Posted October 24, 2018 49 minutes ago, ..Kev said: Good to hear on the saw! Interesting to hear on Grizz! I assume that Windsor is still doing FT? They're really close to each other! I was in Windsor last week and they were still selling FT. There won't be much competition FT doesn't allow discounting, their price is the price. Quote
..Kev Posted October 24, 2018 Report Posted October 24, 2018 44 minutes ago, Just Bob said: I was in Windsor last week and they were still selling FT. There won't be much competition FT doesn't allow discounting, their price is the price. Yea, I'm aware of that.. Just strange to have 2 dealers just a few blocks apart. Quote
Coop Posted October 25, 2018 Report Posted October 25, 2018 Glad you got your issue resolved Bob! Quote
drzaius Posted October 25, 2018 Report Posted October 25, 2018 In Calgary it seems like any store that is even remotely connected to woodworking sells Festool & SawStop. Quote
Bankstick Posted October 25, 2018 Report Posted October 25, 2018 Glad you got the problem solved with the impact wrench. Something like that, to me, is frustrating. A five minute job that takes hours. If you were still having trouble, I was going suggest buying a new tablesaw. One excuse is as good as another! Yes, the inside can accumulate a lot of cellulose fiber materials. AMHIK. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.