Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing

  1. Started by Wood Basher,

    I read a lot & watched a ton of videos before making my first attempt at French polishing (which is also my first attempt at any decent finish). One thing I learnt was that mixed shellac has a limited shelf life. Now I didn't mix my shellac from flakes, I bought ready-mixed polish in a tin. I can find no date on the tin, so how would I know if the contents were too old? One thing I did notice is that I was getting some dark discoloration and I don't know why. It was like a grime mark on the table top I was polishing. I was able to remove it by some vigorous scrubbing with alcohol. Could this be a problem with old shellac? Or perhaps I didn't shake the can enough …

  2. Started by Idaho Andy,

    I recently placed a request for help in the application of ARS on the finish coat of a figured maple table. The table was actually the second one in an office suite that I recently completed. Several of you had asked that I post pictures of the finished table... attached are pics of the table and the full finished office. Thanks again for the help from the forum... it's much appreciated!!!

      • Like
    • 17 replies
    • 3.7k views
  3. Started by SawdustHappy,

    Hi All, I am making some shot jiggers for a friend of mine who works at a bar. I want them to be safe for him to use at work, but also make them last. I was thinking of maybe giving them a coat of epoxy. I also saw a video where someone used a coat of boiled linseed oil followed by a coat of thin CA glue. I have no idea what I am doin so any input would be greatly appreciated!

    • 3 replies
    • 2.7k views
  4. Started by mujaki6,

    Hello all, I have zero woodworking experience and this is my first time trying to do anything involving sanding and staining. Our dining table was extremely scratched up so instead of buying a new one I decided to try sanding it down and refinishing just the top. Because I was only wanting to do the top, I was hoping it would look pretty similar to what is existing on the side of the table and the legs. It didn't have to a be perfect match, just not super noticeable. I also do not know what the wood type is. Anyways, I sanded the entire table down with a rotary sander, using 80, 120, and 220 grit. Before I stained the table itself, I tried out the stain on one o…

  5. Started by Woody n' you,

    I have a 1907 A. B. Chase upright piano that has a beautiful exposed bird's eye maple pin block. It had dried out somewhat over the last 100 years or so. In my ignorance I treated it with mineral oil thinking that because this (mineral oil) is good for preventing cutting boards and wooden kitchen utensils from drying out that it would be a good treatment for any wood. I later came to realize that this may have been a big mistake as I learned that mineral oil will make the wood fibers swell (this is not good for a pinblock) and the wood now has a "sticky" feel to it. The wood was treated with varnish (I'm guessing shellac) when the piano was made. I hope that I have not da…

      • Like
    • 6 replies
    • 3.3k views
  6. Started by Idaho Andy,

    I've just finished the final desk(table) of an office suite project that has included everything from the cabinetry to several work stations and now the final tiger maple desk. My question is about the table top. I've made it through all of my coats of varnish (ARS) with a final satin finish. I've sanded between coats and the final topcoat is now about 12 hours dry... and frankly looks pretty good. My question is what is the best method to finalize the surface (as in removing the roughness or dust nips etc.) to make it perfectly smooth. Since this is a tiger maple table top, there WILL be a constant focus on the surface. I've heard of everything from 0000 steel woo…

      • Like
    • 12 replies
    • 3.2k views
  7. Started by ghost,

    so i am trying to re-finish a chest (hope? blanket?) which is challenged on its condition. it looks like it may have fallen off the moving truck a couple of times in the last 35+ years. i have dealt with making it structurally sound, and started to try and re-do the finish. i sanded down the the top (after cleaning the whole chest with a water dampened rag to get 3 decades of gunk off, and using a card scraper to get what was left of the original finish off the top. which was in really bad shape), and felt that shellac would be the thing to put an amber color back in it, which would be close in color to the carcass which is not as "distressed" as the top. This is where i …

      • Like
    • 21 replies
    • 4.3k views
  8. Started by sjm1580,

    Working on a pecky walnut table top with a moderate amount of filling required. Went with West System 105 coupled with 207 hardener. Began filling the pecky voids with temperature in the shop in the mid 60's and some of the voids have cured fairly well, while a couple have the consistency of hardened snot after 36 hours of curing. Some of the inconsistent areas were filled with the same batch mixture (using the West System Pump setup). I have tried using a hair dry on low heat to induce the curing process in the areas not curing. Just scratching my head on what it could be, same batch, inconsistent curing in similar but different locations, same temperature for a…

      • Like
    • 9 replies
    • 3.1k views
  9. Started by RicksHobby,

    I am looking for help with applying General finishes High performance top coat. I am using this on kitchen cabinets (doors and boxes) that I have painted with Annie Sloan chalk paint. The only way I can get a finish without brush marks is to spray. I am having to do the cabinets in sections to keep the kitchen useable. The finish does not have to be perfect, I just don't want super visible brush marks in the finish. The paint has been sanded smooth with up to 400 grit paper. I followed GF;s videos and used the applicator pad with stocking = still stroke marks Higher quality foam brushes = still stroke marks. Thinned with water = still stroke mar…

      • Like
    • 14 replies
    • 5k views
  10. Started by MisterDrow,

    (Feel free to move this if it should go somewhere else) So I've got some 30-minute epoxy at home and the label says that it needs to cure at temperatures over 70 degrees... now that Fall is nearing its end and Winter is coming (hehe) my garage shop tends to be around 55-60 when I'm out there working. I can get a bigger heater to get temps up but that's for another post. My question is, will the epoxy not cure properly if I try to do it at lower temps? I can bring the work piece inside, if need be, but my wife isn't super keen on me taking up the dining room table while epoxy dries... For context, I'm using it to fill in some bug holes in the blue pine on to…

      • Like
    • 11 replies
    • 3.8k views
  11. I am about to paint my existing kitchen cabinets. I am doing all the standard prep work: wash/degrease, scuff the surface, fix surface imperfections, prime, etc. My plan is to remove all the doors and drawer fronts as well as all hardware. Then I will brush/roll the boxes in place and spray the doors and drawer fronts in the shop to minimize overspray in the house. We intend to go with a white to greyish white perhaps and might go with a darker tone on the base cabinets. What flavor and or brand do you prefer and have the best luck with? At this point I am looking at Benjamin Moore Advance and Sherwin Williams Pro Classic.

      • Like
    • 15 replies
    • 8.7k views
  12. Started by RR60,

    Tried something new on a very small project. Epifanes gloss varnish. But I did not thin. Had the product awhile but never tried it on anything. Playing around a little and gave it a try. Goes on very thick. Took a couple days to dry. But had a very, very high gloss. Almost like the pour on polyurethanes. Then one coat of miniwax poloy thinking it would be more durable. For a very high gloss is there anything wrong with this approach? Instead of these two coats I would have needed about 5 to 10 brush on coats to equal the gloss. But still not sure if a good idea. Thanks for any reply's or opinions

    • 2 replies
    • 2.8k views
  13. Started by rodger.,

    If you recall, I built a table a while back which I dubbed "the xtable" , due to its base. The top is a price of circular glass, about 55" in diameter. Anyway, after daily use for a few years, the top has become scratched. Some are minor scratches, but there are a few deeper ones (the deepest on I can just catch my fingernail on). Any advice on buffing them out?

      • Like
    • 12 replies
    • 3.1k views
  14. Started by PWStoddard,

    My project is to refinish the Douglas Fir trim around two skylights in the interior of my home. I'm now down to bare wood, but I'm uncertain as to what product to use. The wood is subject to considerable sunlight--moisture and abrasion are not issues. One of these skylights is at a height of 20 feet, so I'm looking for a product that will stand up well, and especially one that can be easily refreshed from time to time. I take it for granted that there's no such thing as a maintenance free product! I'm leaning toward Danish Oil with no other coating over it. The idea being to avoid a clear coat that would require sanding/stripping. However I understand the Danish Oi…

  15. Started by ClassAct,

    Gentles: I'm repurposing a kitchen table into a vaulted game table. The vault will be stained and have a topcoat of some sort. The vault floor will be covered by a removable cloth-backed neoprene (think mouse pad). I expect the neoprene to live in the vault, and be removed only for vacuuming out the vault. In the deep, dark, distant past, I've had bad experiences with carpet padding and other synthetic materials reacting with top coats found on hardwood flooring -- sticking to the floor, leaving discoloration marks, or bits of the material sticking to the floor. I'd like to avoid this, even though my table isn't exactly a piece of fine woodworking. Neoprene is s…

      • Like
    • 5 replies
    • 2.8k views
  16. Started by CandorLush,

    If one was to just add a dozen or two coats on a flat panel, throwing caution to wind and getting orange peel all over, would you still end up with a good clear surface once you worked through the grits and buffed it out?

  17. Started by Kothekid19,

    I'm building a breakfast bar for a friend and went with a burnt yellow pine for the top. I sanded, Prestained and then stained. When I stained I found that there were some scratches still remaining from the sanding that are more visible with the stain. What's the best way to get rid of the scratches without damaging the wood or causing issues with the next stain coat?

  18. Started by brianb,

    Hi All, I have a spare 4” dryer duct in my workshop. Normally I finish Oil based outside, but I’m wondering If I purchased an inline dryer vent fan If I could move enough air to finish oils inside while it’s cold? My shop is fairly small (10×15) in the basement and could easily be blocked off with plastic and insulation to be about 6×10. I’m curious if I could get a fan that would move enough air for the smell to not travel through the rest of the house? If so, what kind of CFM would I need to move this much?

    • 5 replies
    • 3.1k views
  19. Started by swiftyfrommi,

    So I have built a dining room table for my wife. It is made from sassafras. My wife wants to stain it a very dark walnut color but I have a question. My top has some small cracks in the middle of the boards. What would be the best to fill them with. I was thinking of staining it first then filling with clear epoxy. Any suggestions or help would be greatly appreciated. Sent from my SM-N910P using Tapatalk

      • Like
    • 23 replies
    • 6.2k views
  20. Started by dflan004,

    I just finished a changing table/small dresser. the outside it painted (thats what the wife wanted). I'm not going to paint in the inside of the case or the inside and outside of the drawers. Its made of Baltic birch plywood. do i need to do any kind of finish inside the case and all the other unpainted parts to protect the wood? thanks

      • Like
    • 6 replies
    • 2.9k views
  21. Started by Coop,

    My first project using a sprayer, shellac and GF HP. I wet down several pieces of cardboard and several pieces of scrap wood. I guess I should have practiced on larger pieces of scrap wood? And I could probably come up with several other excuses that would make me feel faultless but I won't. I sprayed this with dewaxed garnet shellac and after spraying all of the pieces, I saw that I had runs and blotches on several of these panels. After it was good and dried, I sanded with 400 to what I thought looked pretty even colorwise, until I sprayed it with the top coat. Sure made it "POP". Are there any suggestions other than putting this side real close to a wall?

  22. Started by eball,

    Hey guys, Just followed theWoodWhisperer's high gloss finish video on my kitchen table. Did final wet sand with 2000 grid pad, and everything was looking like it should. Then I applied Menzerna's IP2000 polish which brought up a nice luster, except it left tiny white specs all over the surface. It looks just like overspray. You can't feel them, they look embedded in finish. Had to remove them with 0000 steel wool. I tried it again, 2000 wet sand, still looking good, but once I added the IP2000 polish compound, the specs came back so it is definitely coming from the polish..... please help with any ideas. Lots of people have used this method and seems to work.. No…

  23. Started by freedhardwoods,

    I have been intending to get a Fuji Mini Mite 4 when the time comes to get a sprayer. I just recently found the Sprayfine A401 which is very comparable to the Fuji, but $250 less. The Fuji uses a non-bleeder gun and the Sprayfine uses a bleeder. Everything I can find about Sprayfine is automotive related and sounds like a good setup. Can a bleeder gun work for woodworking as well as a non-bleeder? Does anyone here know something about Sprayfine?

      • Like
    • 8 replies
    • 3.5k views
  24. Started by Burr,

    Hello, First time poster. Not really a woodworker, just do what needs doing. I made some cabinets for the kitchen, nothing fancy. The door are a combination of hickory and zebra wood. I finger jointed them together in a 10% Hick, 20% Zebra, 70% Hick arrangement. I then flattened them be taking a hand held belt sander with 36 grit to them. I thinking was that a mistake? Here's my dilemma, I can't seem to get some scratches out then seem to be trailing the hard rings of the grain. Let me explain it another way, the soft rings seem to have belt sander marks right after the hard rings. I have done belt sand to 50, then 120, then Random Orbit Sand to 100, t…

      • Like
    • 17 replies
    • 4.7k views
  25. Started by Ronn W,

    I am considering doing some experimenting with Transtint dyes before I have to finish my current project (cherry). I was thinking about adding dye to shellac to see what kinds of effects I could get. Maybe other experiments, too. Problem is the cost of the bottles on sale on line is $16.40 each. I could easily spend $100 or more on a lot of dye that I may never use again. Anyone know of a source for smaller bottles, or cheaper dye or a discount for buying one of each?

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.