Finishing
2,922 topics in this forum
-
I applied one coat of 1/1 thinned pure tung oil. Let cure 2 days. 4 coats spray lacquer. And this is what happened. Thoughts?
-
-
- 3 replies
- 4.7k views
-
-
Doing some small finish touch-ups and repairs on a high-gloss lacquer finish on a boat interior. Can anyone recommend a good resource for how to deal with small scratches, some dings etc. I know it is a lacquer finish and am trying to get info from the manufacturer on exact type of lacquer and their original finish process. I've done a ton of reading online, but was wondering if there's a good book out there. Thanks.
-
- 1 reply
- 2.9k views
-
-
Building a new bench with a maple top. Can I just leave this top unfinished? It is a workbench, and I have no need to have it shiny etc... Thanks for your responses!
-
- 9 replies
- 4.2k views
-
-
Hey guys, say I were to make a table with a baltic birch top. The grain is faint, it generally yellows a bit with finish and overall is pretty plain and boaring. What type of finish could I experiment with to really make it look like it deserved to be a high end piece of furniture?
-
- 8 replies
- 7.1k views
- 1 follower
-
-
i have a small cherry end table with a high build of water lox gloss finish that has been mistreated for a few years. it appears to have partial pieces of candy wrapper coating embedded in it the ink part of the wrapper for color seams to be left in the finish after some waited to long to clean them up and the sun may have baked it in.. any suggestions on how to rejuvenate the finish? thinner and super fine pad? thanks in advance for any tips.
-
-
- 6 replies
- 2.9k views
-
-
Hi All, I'm finishing a table which I think might be maple and having a few of those dreaded blotching issues. I'm hoping I can salvage as time is tight to start all over. Here's where I'm at... All old finish was sanded off and the scratches sanded out. (The table was a beast to sand in the first place and I ended up going to 600 grit just to get the marks out. Then Bullseye sealer (diluted with equal parts denatured alcohol) was applied very generously so I could sand that without going back to the wood. I sanded again with 320 to give some roughness back for the gel stain, then applied the General Finishes gel stain. The pic below is after three coats. I've s…
-
-
- 6 replies
- 6.3k views
-
-
Hi all, I am about to start restoring/rebuilding my grandfather's chest of drawers (which he made for my grandmother to store LP records) and I'd appreciate some advice on how to proceed. I'm a good DIY'er and have made some wooden things around the house so I know a thing or two but I'm no expert on restoration. Firstly, here's the chest as it stands: The whole unit is quite unstable and loose since it's been put together mostly with screws and very little glue. Since it's not glued, I can disassemble it and repair/replace most of the parts. I'd like to repair the side panels since they're warped. Here's a photo of the side: This is a photo…
-
-
- 9 replies
- 3k views
-
-
I'm finishing off a solid Maple and Jarrah longboard and have jumped straight in the deep end after watching youtube videos. I picked up some West Systems today and drizzled it on, scraped and rolled it around and used a heat gun to remove some bubbles. I'm assuming I can just keep going with a few layers to build up a thicker coat? Any suggestions to go along with this? I was considering getting some fibre glass cloth and putting a layer on with a few coats of epoxy. My main inspiration was this:
-
- 7 replies
- 3k views
-
-
Sanded the floors with orbital sander started with the roughest grit moving to the finer grit as I read while doing research. Did the floor popping and conditioning. Applied the stain and it took unevenly. In the spots where the floor took uneven I tried Mineral Spirits and restained. No luck. It looked blotchy and too shiny. I'm now thinking I should sand down the whole floor. What grit do you recommend?
-
- 5 replies
- 2.9k views
-
-
There are a ton of options out there. I'm leaning towards the Fuji Semi Pro 2 or Mini Mite 3, however there is the gravity fed sprayer and the standard sprayer. The gravity fed sprayer seems a easier to spray up and down since the cups rotate, but I would think it would be top heavy and somewhat awkward to spray. What's everyone's take on HVLP, suggestions on systems. What they like or don't like.
-
-
- 16 replies
- 7.7k views
-
-
Hi all! First time posting here. We own a riding stable and I've been making tack boxes for some of our clients. One box, I finished one box prior to assembly and went very basic with my joinery. Butt joints galore. The next box I am finishing after assembly with rabbets dados and miters. I like the final finish on the one I did preassembly, but I don't know about trying to work around finished pieces to put the finer joinery in place. What order "should" I be going in? Thanks!
-
-
- 2 replies
- 2.7k views
-
-
Working on another bowl. Ambrosia Maple, with some Celtic wood burnings. I turned and sanded the bowl a couple weeks ago,and the better half did her magic and put the burnings on the other night. She noticed some hair line cracks in the bowl, and they started to creak and give. I planned on doing a light sanding after the burnings just to flatten them out some, but I had to apply CA to the cracks to get them to harden up. The CA on the inside isn't really fading with sanding, so I'd probably have to sand off the burning (and piss her off) to get the CA sanded down. So.... Here's what I'm thinking. Perhaps, after lightly sanding them smooth, and applying some Tu…
-
-
- 7 replies
- 3.2k views
-
-
I want to crackle an oil based poly finish. Is there a technique or product for this?
-
- 2 replies
- 2.7k views
-
-
My in-laws have asked if I would be able to make a couple of those slotted reindeer decorations for their yard. Happy to take on a simple project for them (they truly are wonderful people) I said I would love to. My question is, what type of finish should I be using on the end product to seal it from the elements? We don't get a lot of lasting snow around here (SW Idaho)... we'll get one or two heavy snowfalls that might last a week or two and the rest of the season it's just cold and rainy. I had planned on using exterior house paint for them (they just want them to be white) but I wasn't sure if I should also be using some sort of wood sealer to help it all to last l…
-
-
- 8 replies
- 3k views
-
-
I love this stuff, been using it about 10 years. I've tried Tung oil and BLO but neither has the build or compares with finish I get with Liberon furniture oil. Anyone ever made their own?
-
- 3 replies
- 2.9k views
-
-
I have an Earlex, which I quite like. It's well used, and I feel like I would like a "step up" in the HVLP arena. I have been reading about the mini mite 3 (about 750 CDN) and the mini mite 4 (about 1000 CDN). The 3 will suit my regular repertoire of general HPP, but I would also like to spray latex paint on rare occasion. Has anyone sprayed latex through the mini 3? Don't really want to mess around with thinners, so if I must thin with a 3 stage, I'll just pony up for the 4 stage and be done with it.
-
-
- 3 replies
- 3.6k views
-
-
Hello I am looking for some help on finishing my project I have been working on. I had a bunch of leftover wood and I made some necklace/bracelet holders. I made the out of varying types of wood, Walnut, Maple, Mahogany,Cherry and 1/4 sawn white oak. My plan is to stain them but do not want use the same color for all of them and with the walnut I am just going to leave them natural with coat of finish. What are some good colors for these? I know it is a loaded question. I do not want to go buy a bunch of different stains and experiment and find out there are some U do not like then I am stuck with it having used it. The maple is the hardest to find a suitable color I…
-
-
- 8 replies
- 3k views
-
-
I decided to finish the No. 7 box with Danish oil. I like the 'chocolate/vanilla' contrast. The directions (yes I read them first) say to wait 72 hrs before using polyurethane. I want to avoid two chemicals that don't like each other, anyone have any experience protecting an oil finish with a satin poly?
-
-
- 13 replies
- 14.5k views
-
-
Question...using the subject product and it appears that I get very fine brush marks on select ares of my work piece, not uniformly across the piece. I'm pretty amateur here...any ideas?
-
- 6 replies
- 2.9k views
-
-
My husband made a bathroom vanity and I may have ruined it. I stained it with Minwax oil stain and it is very blotchy. I have now read that I should have used shellac first. I also have read that spraying with toner will probably fix it but we don't have a sprayer. Would Minwax Polyshades be an option? We want a dark espresso color.
-
- 5 replies
- 2.9k views
- 1 follower
-
-
Picked up some Seal-A-Cell and satin Arm-R-Seal for that walnut desk I've been working on. I've never used it before and figured I should test it out. Applied the sealer and four coats of Arm-R-Seal on a rough sanded piece of walnut scrap to test it out. This stuff rocks! https://imgur.com/a/p5wLk
-
-
- 62 replies
- 24.3k views
- 1 follower
-
-
I've got a commission to build two twin beds out of Poplar, but the client wants a golden stain, like golden oak of Minwax. The question is, I know poplar is blotchy at times for staining, should I use a wood conditioner prior to staining? If not a wood conditioner, what is the best way to get a stain evenly on Poplar ?
-
-
- 76 replies
- 20.4k views
- 1 follower
-
-
Hey guys wondering if using paper towels is fine for applying stain and finish? It seems like whenever I use rags they are ruined and can't be used again. What do you use?
-
-
- 9 replies
- 38.5k views
-
-
I'm asking forgiveness for the lack of fine wood working in the next post. I'm trying out a few ideas I've come across. I'm building a stool for the wife using plywood and hairpin legs (please don't be mad) that I've made. The top is made from strips of plywood that I've glued together. It will be sanded soon and a round over will be put on it. Any suggestions for finishing the ply?
-
-
- 16 replies
- 5.8k views
-
-
The wife wants what she wants. I'm building a farmhouse kitchen table. A cherry top and white painted (turned) legs and aprons. Tonight my wife hit me with how she wants a distressed paint, partially sanded through. Whatever. I'm less than enthused with this project, but I just have to live with the fact that the table top will hopefully have some hint of craftsmanship and the crappy trendy base was all her idea. I've done the distressed paint thing before, a couple years ago we refinished a bunch of reclaimed window frames. We painted them one color, let it dry and painted with a contrasting color on top. A light sanding, just enough to go through the top…
-
-
- 13 replies
- 3.4k views
- 1 follower
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·