Finishing
2,922 topics in this forum
-
ok, so i have a bunch of small crosses i have built for the local trophy shop and decided to use spray lacquer in a can for ease of use and quick drying time, i works great but my problem is with the end grain soaking in the finish, after four coats and its still soaking it in. should i use something to seal the end grain before applying the lacquer? sanded down to 320 if that makes a difference, the wood i'm using are white and red oak, cherry and mahogany, this is the first time for me using lacquer and it seems to be a quick and easy finish especially in this application, thanks in advance for the help guys.
-
-
- 15 replies
- 4.5k views
- 1 follower
-
-
I haven't done much yet and am still learning about stains and oils. So this question is pretty basic. I'm looking at a wood slipcover for a special book. Probably several. Looking at doing versions of it in poplar, cherry, maple, walnut. Just 1/4" thick material. It's not hard to make, but finishing it is the question. How long should a stain or oil dry or set in before a cloth-bound book won't absorb it? Maybe 48 hours? A recommendations or warnings?
-
-
- 12 replies
- 3.2k views
-
-
First time using mineral spirits, bought a bottle of This today. Klean strip "green" mineral spirits. Started to make up a batch of the Drunken Woodworkers BLO - WOP - MS Finish for a sycamore Salt shaker I'm turning. The spirits look like milk. I thought they were supposed to be clear... As I had already mixed the WOP and BLO, I finished making the batch. This stuff requires constant shaking to keep it mixed (I'm using generic ketchup dispenser bottle), else it settles out within 30 seconds, looks like curdled milk falling to the bottom. I applied it anyways, as the shaker is almost a loss, it's basically a lidded box, but the tenon is a hair too loose …
-
-
- 30 replies
- 7.7k views
-
-
We just purchased a 1920's home and have hired someone to refinish the floors prior to moving in. I have attached a photo of the results from staining the fir floors in two rooms, this is pretty typical for all rooms with fir. I feel the stain is blotchy and uneven. Has the contractor made an error? Should I ask him to start over or is this typical for older floors? I guess I would like to know if I am being overly ctitical? Move in day is only 3 days away. Also, the lighting is different in each room which makes the color seem off in the photos.
-
-
- 2 replies
- 7.5k views
-
-
Hello all! We are in the very long process of restoring a 100 year old house. So to make a long story short, we are doing the painstaking process of attempting to remove all the stain off of these incredible tongue and groove heart pine walls. The same planks are on the floors and ceilings. Some are a bit termite damaged but overall are simply beautiful. Anyways, we are struggling with getting the stain off. We are burning through sanding discs on my orbital sander like there's no tomorrow. Even at 80 or 60 grit, the amount of residue coupled with the resin from the heart pine gums them up way too fast With such a huge project, would you recommend just goin…
-
-
- 43 replies
- 13.1k views
-
-
I applied two coats of teak oil to a project. I let the teak oil sink in for about 15 minutes then wiped the excess off each time. After letting the project dry for two days I noticed light colored patches in some places that are rougher than the rest of the piece. It almost looks like it has been sanded in these patches. I wiped the whole piece down with mineral spirits before applying the oil and didn't see any of these patches. It is difficult to see in these photos, but you maybe able to make out the lighter covered patches on the maple. I am wondering what might have caused them and how to get rid of them. Thanks
-
-
- 7 replies
- 7.4k views
-
-
Hi all. I have a half-can of shellac that will expire in a few months, and a bunch of scrap pieces that are never going to be turned into anything useful. I am getting a couple of weeks vacation this month, and was thinking of doing some finishing experiments with them because hey, it beats throwing them out. I've read a couple articles about making your own toners and stains by taking shellac, oil, or varnish and mixing in dye or pigment. The articles talk about getting said dye or pigment from art supply stores, but they're comfortably vague about what you should actually be looking for on the shelves. Has anyone done this before, and if so, could they offer some produc…
-
-
- 10 replies
- 3.5k views
-
-
The missus wants me to make magnetic bulletin type board 12" x 18". I want to give it the appearance of wood, if I use 1/4" ply, I'm concerned about the strength of the rare earth magnets. I'm thinking of using a wood veneer to minimize the thickness. What would I use to glue the veneer to a piece of sheet metal. If ply is used and a wooden frame I am concerned with the weight of the finished product. I have never used veneer before, so any tips are welcome.
-
-
- 3 replies
- 2.9k views
-
-
We have a maple bar in our kitchen that after 15 years needed refinishing. I stripped it down, sanded, wiped it down with acetone and proceeded to apply a coat of Behlen Rockhard Table Top Urethane Varnish that was thinned 50% with paint thinner. However, now it won't dry. The weather is warm (about 75°F with pretty low humidity) and I have a ceiling fan in the adjoining room working at a low speed. There are patches where it has dried but most of it looks like the varnish was applied just a few minutes ago. If I thinned this too much, what do I do now? What if it won't dry at all? Do I try to remove what's still there with rags soaked in paint thinner? …
-
- 15 replies
- 5.6k views
-
-
I finished a hall table a few weeks ago and since that time, learnt about grain filling. The timber I've used is open grained and the feel of it is not quite as nice as I thought it would be. I've used Mr Maloof's formula to finish it but I want to strip the top, fill the grain and refinish. Would a card scraper be the most effective way to avoid clogging up paper?
-
- 1 reply
- 2.6k views
-
-
Hi - I am a new user. I recently bought these blocks to make a table. So far I have made good good progress. However I scratched a couple of the tops and they look rather nasty. I was wondering what kind of finish these blocks have so I can atleast try to make it right again. I have been told that these are rubber. I bought them at Sears. I don't want to re-sand the whole top however. Thanks for your suggestions. Saman
-
-
- 12 replies
- 3.3k views
-
-
I usually use tung oil as a first coat on almost everything I make and I almost always buy whatever is cheapest at the time. If formby's and minwax are priced the same I choose formbys because the can looks cooler. Between these two versions of "tung oil" or anybody's other brands including the "100% pure tung oil" , I really don't find the end result to be any different. Granted the viscosity is noticeably different when applying the pure tung oil and the drying times vary across the board but all the tung oils seem to take the next steps of my finishes equally with seemingly equal results. So my question is, and I don't care what the material data sheet says, wh…
-
-
- 8 replies
- 16k views
-
-
I refinished two old walnut side tables for my father and put 4 coats of Arm R Seal satin. As the finish began to build it started to take on a plasticy (that's a word right?) look. For those of you who use Arm R Seal, or other applicable (Waterlox) finishes.... Do you lay down a few coats of gloss first to preserve clarity and then put a final coat or two of the desired sheen on last? What is your method to keep a clear finish when the desired sheen is NOT gloss. Especially on a dark colored wood. thanks in advance!
-
-
- 9 replies
- 4.1k views
-
-
I have an old china hutch that I have taken apart and plan on converting the bottom half of to a TV stand. It is from the 50's or 60's and the existing veneered finish on it was called limed oak I think. The doors had decorative wood carvings attached on the front that I removed, and the wood under the carvings has aged differently. Sanding so far seems to have had little effect. Is there any way that I can clean or treat this to make the wood match? Keep sanding? It is a veneer, so I am worried about sanding too much off. Thanks
-
- 0 replies
- 2.9k views
-
-
Any suggestions on how to dispose of old cans of finish (stain, varnish, paint)? Here, you're not supposed to put it out with the trash unless it is dried out. But the local gov, in it's infinite benevolence (or is that malevolence) doesn't give any other guidance nor provide another disposal method. I can take the stuff to the hardware store and pay per quart for disposal. Local requirements will no doubt vary, but I'm looking for an idea better than leaving the lids off and waiting 6 months for them to harden.
-
-
- 27 replies
- 9.3k views
-
-
I'm starting a federal style table made of home grown cherry. I'd like to dye the wood a seeped shade of red; however, I'm not sure when to apply it. If I wait until I'm finished the dye will cover the inlays (stringing, cuffs and waist band) but if I apply it before the inlays I'm afraid I'll remove some of the dye when I sand the inlays. Any suggestions?
-
-
- 13 replies
- 3.5k views
-
-
There was some talk about pore fillers elsewhere and I mentioned P-of-P. This is an old technique but, thought I'd re-share for those who might have missed it. There is no one product that suits all situations but, for things with big pores like red oak that will receive an oil based finish, it doesn't get much cheaper or easier. I mix the P-of-P to about the consistency of heavy cream. Apply it like any filler; across the grain, in circles, etc to drive the material into the things you want to fill. Once dry (it dries fast) wipe it with a sponge to get most of the spoil off, sand to your desired finishing grit and apply your oil based finish. The oils turn the …
-
-
- 10 replies
- 7.9k views
-
-
I am cleaning up an old veneer headboard (from 1920's or 30's). I wiped it down with a little Mineral Spirits to clean it up (it was dusty and had stuff on it from years of use and then storage) and evaluate the existing finish and the surface powdered. I am wondering if it was a wax, but it did wipe off and the under finish is still there. I need to make sure it is clean and then I need to make it ready to mount to the bed. Any idea what could have powdered? Jeff-in-kc
-
-
- 6 replies
- 3.7k views
-
-
My mother is getting her kitchen walls painted after 20 years of living there. She was doing a deep cleaning spree on the kitchen and she bleached her stained cabinets. They went from having a high gloss shine to a dull satin shine now. Aside from 20 rattle cans of poly, what can be done to get the shine back. Note, she nor I have a spray system to spray anything with ease Sent from my iPhone using Tapatalk
-
- 4 replies
- 3k views
-
-
Hi guys, as some of you are aware I am very new to woodworking but loving it. My wife's birthday is tomorrow and I have spent the last three weeks building a jewelry box for her out of walnut and Cherry. I have put one coat of Arm r seal on it and then disaster struck, my boys got in the shop and to make a long story short my last can of arm r seal is no longer. I need to get 2-4 more coats on the box before tomorrow but can't find arm r seal locally. Does anyone have any suggestions on an alternative that would give similar results that I could find at Home Depot/Lowes that would work well with my one coat already applied? (Pretty much need to find it today and get …
-
-
- 4 replies
- 8.4k views
-
-
Hello, I recently inherited a nice old dresser that had been stored in damp conditions. It had white mildew growing on the sides that damaged and discolored the finish. I washed the dresser with a mixture of Murphy's oil soap and a little bleach. An antiques dealer told me to use 1/2 shellac from Lowes and 1/2 denatured alcohol and to rub that on the discolored/damaged area. I did, and it really seemed to make the sides look better. I did the drawer fronts and top too, and they did not come out well at all. Now they look streaky, uneven, and on some drawer fronts, cloudy. Is there anything i can do to restore this piece? I don't want to do a full blown refinishing j…
-
- 9 replies
- 3k views
-
-
Does anyone know the difference between zinsser sealcoat 854 and zinsser sealcoat 824h?
-
-
- 16 replies
- 4.5k views
- 1 follower
-
-
Are there any quick and easy tricks to determine when a piece of sandpaper is worn out? I love the pencil trick where you scribble on the board you are going to sand, then sand until the pencil marks are gone. This has really helped me. Is there something equally simple and clever that I could use to decide that the sandpaper has done its duty and should be "retired". In the past I think that I was tossing paper out with a lot left to give. Now that I am using paper longer I see that what looked worn to me in the past is still removing the pencil marks. But when to toss it?
-
-
- 44 replies
- 22.8k views
- 1 follower
-
-
Hello, I'm finishing up the prep process on my dining room table. It's oak and I think around one hundred years old. It's stripped and sanded and ready to be stained. I thought I was ok with a very light stain on the table. Now that I sit back and admire all the hard work I put into it, I thought it would be silly of me to accept this stain without consulting some experts. I have no idea what caused it, and I tried my hardest to remove it. I'm afraid to sand it down even further. The first two pics are the bare wood and the last two are what the stain looks like when wiped with mineral spirits. Any thoughts on how to take care of it?
-
- 4 replies
- 3k views
-
-
Work for a painter and one of the guys power washed to deep leaving lots of lines from hitting wood to close so they sanded the lines and fanned em out and we then put stain on it and it left it looking like this. I am not sure how to fix it so stain evens out. If anyone knows of a product besides wood conditioner to try please any advice is welcome
-
-
- 6 replies
- 2.8k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·