Finishing
2,922 topics in this forum
-
I looked and found an earlier discussion regarding tung oil finishing. It didn't quite answer my concern. Is tung oil the last step or does anyone recommend a top coat of something? And if it is the last step, is it necessary to reapply the finish periodically?
-
Hi All, I'm new here and have a small project of now finishing my solid body guitar which is Mahogany and the neck is Maple. Starting with the Mahogany body, I want to pop the grain with a dark color while not coloring the rest of the body. I might color the body to a light brown but the grain will be darker. How can I uptown this? Note: I do not want to fill the grain, I want a natural porous look after final finishing.
-
-
- 14 replies
- 9.2k views
-
-
I'm sure I am way over analyzing and over thinking all of the finishing options out there. A very simple thought hit my head that may really clear things up for me. Correct me if I'm wrong and please get me on the right track as well. It finally struck me that the differences in the different finishes is more in their properties and what applications they are intended for than their appearances? I mean...color gets taken care of by stain; and the different finish options all have satin, semi gloss and gloss options. The difference between polyurethane and say shellac may be more in the hardness of the outer coat and these differences..hardness, flexibility drives the…
-
-
- 14 replies
- 3.3k views
-
-
I've been experimenting with some HVLP conversion guns spraying GF High Performance Satin. I am finding that when I lay down a thin, even final coat I end up with a somewhat textured surface. It feels similar to what a formica countertop - maybe slightly more rough. The area I'm spraying is 42" x 72" so overspray is difficult to control without a more powerful exhaust system. Is this normal? What is the best way to smooth the final coat? Brown paper bag? Scotch brite pad? Steel wool? How long should I wait before buffing? I've used the paper bag trick in the past but it leaves small scratches. Thanks!
-
-
- 9 replies
- 4.2k views
-
-
Hey all, I am building a simple reclaimed bench for a friends wedding that they are having guests sign with a sharpie. the material is oak and I'm thinking I will need to apply a coat before sharpie time to keep the ink from bleeding into the soft grain then apply a finish coat after. I'm thinking BLO first then poly after thoughts from the experienced appreciated ETA: or should I go poly, poly? I really have no idea.. thanks
-
-
- 8 replies
- 3.7k views
-
-
This is a beautiful Parota slab coffee table top I've been working on for a client. I haven't run into this problem before. There are three areas where horizontal lines are seen in the sap wood running horizontally across the face. I had this slab planed down and I also sanded these areas heavily, to the point I wasn't comfortable going any further for fear of mis-shaping the top. My guess is these are remnants of the sticks used to stack the slab when it was drying. I don't want to keep removing more material from the top - want to retain thickness of slab. The coloration also matches perfectly the colors in the slab itself - it's not "dis-colored" in that way. …
-
-
- 9 replies
- 6.3k views
-
-
I am building an outdoor grilling cart which I will be mounting my Weber grill into. I am using a 72" X 36" Birch Butcher Block as the counter top (don't worry I will be using a heat shield to prevent the wood from starting on fire). I am trying to figure out the best way to treat the wood to help it hold up to the sun, use, weather, etc. I will have the cart under cover for the most part and don't mind the idea of just using butcher block wax and applying it regularly but I read about and have considered using a diluted salad bowl finish on the block instead as that seems like it might hold up better. Does any one have an experience or advice with an outdoor b…
-
-
- 15 replies
- 4.4k views
-
-
I've looked through several areas of this forum and found bits and pieces of information that are applicable to what I'm about to ask, but nothing exact, so please forgive me if this seems repetitive or was already discussed elsewhere and I missed it. I am building a farmhouse(-ish) dining room table for a friend/customer. They chose knotty pine for the material and want the coloring to be the color of Watco Danish Oil's dark walnut color; however, they've stressed the importance of maintaining the visibility on the wood grain. At first, this didn't sound like a problem as I've used danish oil on other projects, but as I was doing some specific reading, it turns ou…
-
-
- 4 replies
- 2.9k views
-
-
Hi all, I've been woodworking for about a year now and have a few projects under my belt and like most people I loath the finishing aspect of it. I've been using wipe on finishes but am thinking about getting into spraying. I tend to pick extremely expensive hobbies and am not a man of means. So budget friendly is paramount. I already own a 30 gallon compressor, not sure of the cfm specs. What would be a decent for the price gun to start out with. Would probably want to spray Lacour or shellac mostly. 75 bucks is about the most I'm willing to spend at the moment. Looking for some info from some of you that might have or currently use a lower end setup. Not trying to expos…
-
-
- 13 replies
- 4.5k views
-
-
I'm in the process of refinishing a solid oak dining table but am having trouble determining what caused some of the marking on its surface and how far I need to go to restore it. So far I've applied one coat of Citristrip and removed the top finish layers. Based on the pictures I've included, can someone identify what sort of damage I'm looking at in these and how far down in the surface I need to go to repair or hide them before applying a new finish coat? Any help or suggestions are much appreciated. Thanks, -Adam
-
-
- 10 replies
- 3.1k views
-
-
Okay...want to make this pretty short and sweet as it's late and my googleing attempts are as exhausted as I am. Have a kitchen table that had burn marks on it and had the idea of refinishing it the way I wanted it. Started off as a Pinterest idea..thought I had it covered..apparently I'm not as crafty as I thought. Any who I took a trip to HD..got myself 2 different color stains, wood conditioner and some polyurethane. All minwax brand. I have no knowledge as to what type of wood it it...seems to be MDF..with a thin layer of some wood. Sanded it with an OS...60 then 100 And finished with 150. Applied the conditioner and then coated with my first color choice of stain, le…
-
-
- 19 replies
- 4.6k views
-
-
Hello fellow woodworkers! I am a little out of my element here as this project is for outdoor use. As such I am using an Outdoor stain "Olympic Maximum Cedar NaturalTone Semi-Transparent Exterior Stain". My issue is that my wife is rushing this project to be completed and ready to use for a cookout Saturday evening. My first opportunity to apply the stain will be this evening. The product says it is not completely cured / dried for at least 24 hours. Being as it is that these are benches, I need to stain all 6 sides of the 2x4 Cedar boards. Given the time constraint from my lovely wife I cannot wait 24 hours between sides. So, my question is, how long do I …
-
-
- 6 replies
- 26.5k views
-
-
i recently made a patio table for my house. i was planning on using a clear outdoor finish, but the wood i used was cheap and doesnt look all that great. so i wanted stain it. What is a good outdoor stain to use? i was looking at the general finishes 405 exterior stains but i cant find a place to buy them. What do you guys use? can i use an indoor stain and put an outdoor varnish or a sealer on top of it?
-
- 2 replies
- 2.6k views
-
-
Hi Folks i have a question or two about finishing a top of a bookcase that is "figured" cherry and walnut. Not really sure if the board is figured or not. The top is made of a 12' board I cut in half and glued together and is now 6' by 12" with a walnut trim and will have breadboard ends. I have not used cherry before but have done some research on finishing cherry but could use some advice. I attached a picture of the wood but not sure it really gets to the various colors that are apparent. After sanding I can see a hint of pinkish, whitish curly figuring and some lighter brown areas. I am leaning toward either just spraying on a polyurethane topcoat or using a Dani…
-
-
- 12 replies
- 6.2k views
- 1 follower
-
-
I need a little advice on a project. I have made a bookcase out of cherry plywood for the sides and shelves and solid cherry and walnut for the top. 1) Do you lightly sand the plywood? 2) Will Danish oil look okay on it? I only had a small piece left over and could not tell from my sample. I have read that you should not use any oils on plywood. Thanks in advance.
-
- 5 replies
- 2.9k views
-
-
So I have a clients table that I am getting close to being finished with and they changed the color on me.. I had planned on using a mix of general finishes dark brown and orange dye stain to spray on but the sent me this picture of a Pinterest table they like better... My question is what's the best way to copy this? Easy answer is to find the min wax stain that looks alike and slop it on. The blotchy-ness would look "rustic". Is there a better way to match this color with the black undertones? Thanks! Sent from my iPhone using Tapatalk
-
-
- 39 replies
- 7.4k views
-
-
My sister's friend is building a new home with exposed pine beams. He wants to keep it as white as possible. He's looking at Rustoleum Ultimate Polyurethane, Deft Interior/Exterior, General Finishes EnduroClear and two flooring products, Lenmar and Bona which I've never heard of. Does anyone have any experience with which WB Poly is the 'whitest?' This will be a brush-on, not sprayed, application. Thanks.
-
- 7 replies
- 3.2k views
-
-
Has anyone used any of the General Finishes Exterior 450 products? Either the stains or the clear varnish? Curious how they hold up. Also how the clear varnish would compare to something like Epifanes. I have some cedar Adirondack chairs I made a few years back that need refinishing and am trying to decide what to do with them. I had originally put some TPF on them and it did not hold up. Going to go more film finish this time. Either the CPES & Epifanes route or try something like the GF 450 Exterior product. Thanks!!
-
- 3 replies
- 3.1k views
-
-
So I have dark stained wood dining table. The finish is starting to look pretty bad and I would like to put a fresh coat on it. Unsure of the finish used, I dabbed a bit of Lacquer thinner in an inconspicuous spot and it immediately took off the finish and the color. I assume this means the finish was lacquer to begin with. So I was thinking I could clean in up with some Mineral spirits, do a light sand, the spray a couple new coats of lacquer with sanding in between. My question is whether the solvent in the lacquer itself will cause a problem while spraying? (i.e.: remove or blotch the stain underneath) I read somewhere it might cause issues. Some said t…
-
- 1 reply
- 3k views
-
-
Looking for staining for advice – I’ve been making these rulers for 3 years now and the last 4 months have been having issues with the stain taking evenly. I’ve never had the problem before, then all of a sudden it seems every board is coming out blotchy and striped. I used Pine wood, so I recently read that I should treat it with a pre-stain conditioner, so I’ve started doing that. It has helped on some, but most of them are still coming out all funky. Any ideas what else I can do? Is there a chance the store I buy the wood from has changed the wood and that’s why I’m suddenly having all these problems that I never had before? It has been winter here and I …
-
-
- 5 replies
- 3k views
-
-
I'm working on a project where I'm taking some long leaf pine to make a desktop/table. It's going to be 72"x28" more or less and that's including a 1" cherry breadboard all around. I'm also inlaying 3-1" strips the length of the desk evenly spaced. My question is what kind of finish would you recommend? I originally thinking of doing some epoxy/liquid glass, but I'd be curious to hear your thoughts. What's the difference between lacquer and polyurethane? Would a spray on finish be better than paint on or roll on?
-
-
- 7 replies
- 3k views
-
-
Hello i have recently, finished a harvest table with matching bench, made out of very old pine. I stained the bench first with min-wax Jacobean finishing stain. The bench took the stain very well and went as dark as I wanted but I noticed it was inconsistent and bloctchy. As a preventative to stop the table from getting bloctchy and to ensure a more even coat , I used a sanding sealer on the table top only as I wasn't to concerned about the bottom as it wouldn't be seen with exception of the skirt. As you can see in the picture the difference is substantial and even after I left the satin on for 15 min it did not get darker. To say the least I am freaking out as no…
-
- 5 replies
- 3k views
-
-
I am working on an old dresser, 50s vintage. The dresser is mostly hardwood but the face of the drawers is (well, was) beautiful bookend veneer. Unfortunately, a guest put a vaporizer in front of the dresser and buckled the veneer. I thought since the vaporizer had done such a good job of debonding the veneer that this would be a (relatively) simple job. NOPE! I have tried a hot towel on the veneer face. I have tried a steam iron. I have tried a dilute vinegar solution. I have tried a heat gun. This veneer is glued on with the best glue on the planet. The vaporizer discharged onto the veneer for about two weeks so there was plenty of time to debond the g…
-
- 0 replies
- 2.9k views
-
-
Has anybody had any experience putting polyurethane (or Arm R Seal) over a water based finish like minwax's Polyacrylic? I applied some General Finishes poly over some Polyacrylic on a small section of a door and it surprisingly warmed up the color and looked really nice. However I'm not sure if it will adhere well enough to last. Wondering if anyone knows more about this than me...(finishing is my weak spot) Thanks! Sent from my iPhone using Tapatalk
-
- 5 replies
- 2.9k views
-
-
I am using a birch butcher block in desk design (bought the butcher block portion) and I need to seal it for long term use/abuse. It will be a computer/workstation desk and I would like to prevent as much wear on it as possible. A satin/matte finish is what I want without any yellowing. How should I finish this?
-
- 5 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·