Finishing
2,922 topics in this forum
-
High folks, I'm a new guy to this forum. I am probably asking a question that has been asked and answered all ready, please bare with me. I purchased teak furniture, a table and ten chairs, about 15 years ago. The furniture is outside on my deck. When the season is over I cover all the furniture. I used teak oil every spring. But the finish has become a dark brown and the table has "stains" on it. What can I do to bring it back to its golden honey color? When it comes to working wood I am trying to work my way up to novice! I will need step by step hand holding. I am open to any advice, but I will need a lot of guidance. Thanks Papa …
-
-
- 12 replies
- 5.4k views
-
-
Every project needs to have something new that I haven't done before. This time it is a veneer box with 1/4" square edge banding. I am using bubinga waterfall veneer and probably clear maple on the corners. Similar construction to Marc's humidor. If the project goes really well I want to to finish it with a gloss finish and give it my granddaughter What are some of your favorite high gloss finish systems for this type of project?? Of course if things don't go so well I will use a satin finish and store extra wood screws in it.
-
- 4 replies
- 2.7k views
- 1 follower
-
-
I've been struggling with spraying GF Satin High Performance Top Coat on a mixed barn wood table. I'm currently using a cheap Harbor Freight Turbine (Rockler clone) HVLP. http://www.harborfreight.com/high-volume-low-pressure-spray-gun-kit-44677.html The gun seemed fine for spraying oil based stain and poly however that tends to be extremely messy and very slow to dry. I'll be sticking with waterborne products from now on. Applying a uniform wet coat leads to ripples / orange peel. The only way I can get the finish to lay on is extremely thin coats after thinning the material with 20% extender and 5% water. This is so thin that it's basicall…
-
- 15 replies
- 7.4k views
-
-
Just wondering if anyone has any ideas on possibly repairing this bullnose? I'm hoping there's a way instead of tearing it out. The lip that extends out over the laminate flooring has cracked, and I going to repair it to prevent it from getting worse or completely falling off.... Thanks.
-
-
- 5 replies
- 3k views
-
-
I am just getting into wood working and building a work bench with some MDF, can it be sealed, and what would you use john
-
-
- 33 replies
- 22.6k views
-
-
I've built a couple bookshelf speakers and am currently painting it with http://www.lowes.com/pd_53310-4-410.0065048.005___?productId=3158911&pl=1&Ntt=valspar+black+gloss+latex+enamel . I'm looking for the highest gloss finish possible. I'd like to use a clear of some sort. I purchased http://www.lowes.com/pd_45869-678-33050000___?productId=999913663&pl=1&Ntt=minwax+fast+drying+polyurethane based on recommendations of using Poly for clearing. Can anyone confirm whether this is a good option or not? Thanks all!
-
-
- 8 replies
- 2.7k views
-
-
I have made a wooden sign out of laminated plywood that is approximately 1' X 3' and painted it with enamel. It will be mounting 1/4" thick raised letters on it. Since it will be mounted outside, I am looking for some tips on the final finish. I was thinking about polyurethane over the entire sign after I mount the letters but not sure whether to use spray, due to the raised letters, or brush on. Or maybe something else is better that will give me a nice smooth finish. Any ideas?
-
- 6 replies
- 3.1k views
-
-
I am new to filling knots in table tops. Generally I just use clear wood and work around the knots. However I did just get some air dried shingle oak that is riddled with small knots (smaller than I diameter of a pencil) it is some beautiful wood and I am going to make a table top from it. I have heard good things of the West System Epoxy but I was wondering if this was the best to use and if so what all do I need to order. I have been looking on Amazon and it looks like I can get the 105 resin but I didn't know which hardener I needed to go along with it. I was also curious if anyone knew of and system that might be cheaper. $100 just seems like a lot to drop on epoxy. …
-
-
- 20 replies
- 38.2k views
-
-
I'm in the process of finishing a island table for my cottage that I have fully constructed from salvaged 3x9 fir timbers. For the base I used a wire brush to clean up the boards and that is working out fine as it has given a very rustic look. However for the top I had to cut and plane all four sides of the boards to get a uniform, flat and of course clean surface. The end product will be a butcher block style top that is about 3 1/2" thick (4x6 is size). My problem is, what is the best product to finish the top with? I've looked at Linseed Oil, Tung Oil, combinations of oil and wax but really can't find something that gives me 100% confidence. The bare wood is very…
-
- 5 replies
- 3k views
-
-
Im finishing up a countertop that Ive made out of Maple. Id like to get a little more color out of it, but it not to be too dark. BLO is the closest ive gotten to the color I want over some of the stains that I have tried. I also want a protective finish over it. Can I poly over the BLO once I apply? It will be an oil based poly so they are compatible-my issue is with the color that BLO has made, will that be "locked in" by the poly or will it fade over time? any hlep and or suggestions would be greatly appreciated. Ive seen back and forth remarks regarding this. I have a few days to allow the BLO to "cure" or dry, but I dont have months. Any help? Thanks
-
-
- 18 replies
- 10.3k views
-
-
Hi All, Recently purchased oak treads/risers from lumber liquidators for my stairs. They are red oak, unfinished. After measuring each one, cutting and sanding to size, I then stained them using Miniwax Cherry 235. After letting them dry, started applying Miniwax Fast Drying Polyurethane, Clear Semi-Gloss. It only take a few minutes, and white patches started appearing on some of the treads. image is attached. It is not a patch where you can scrape off with your finger nail, i have to sand down the poly, then sand down the white patch, clean it off, re-stain, let it dry, and then re-apply the poly. I have been repeating this process multipl…
-
- 24 replies
- 23.4k views
-
-
I'm in the middle of finishing a bench. Pretty much three slabs of walnut. I have two coats of Waterlox on it and I want to sand in between coats to build up a finish coat and to make it baby bottom smooth. I pulled out some 600 grit wet/dry paper but it clogs up after a few passes. I'm thinking I need some sort of lubricant on it but I'm not sure what to use. If I wanted to do a wipe on finish, I could probably use the Waterlox itself and then simply wipe it away, but as I want to build up a few coats, that won't work. Also, what's the best rag to wipe off the dust? Any suggestions on what to use would be greatly appreciated. Thanks, Allan
-
-
- 18 replies
- 9.2k views
-
-
I have another thread on here about sanding a bar top I built in my basement made of birch ply (pictures attached). I plan on gel staining it. It is already built in a fairly enclosed sub-level basement and I would like to avoid the fumes of an oil based topcoat because my wife is pregnant. Spraying is not an option as I don’t have the equipment, experience, and the surrounding room has already been renovated, painted, and furnished. The other issue is that the bar is fairly big…10 feet in length with a total finishing surface area of 100 square feet….and from what I’ve read, most water-based tops typically dry faster than I might be able to work on this. I’ve been goo…
-
-
- 24 replies
- 6.3k views
-
-
So this is my very first post, but have been following here for awhile. I am currently going to building a Murphy Bed from the plans given with the order from Rockler. The plans call for Cherry veneered Ply and cherry, I really do not want to buy $120 dollar ply when birch is $60. If I used birch ply and Cherry for everything else, would finishing be difficult. Would the colors just be to off if I were to use Arm-R-Seal or to blotchy if I were to use a darker stain. This will be my biggest project yet as I have only been woodworking for about 8 months now.
-
-
- 7 replies
- 2.8k views
-
-
Took the day off and I am almost done with the final sanding of my son's crib. I'm using 600 to make the poly super smooth and am pleased with how it's turning out so far. My question is how do I ensure that I get all of this super fine poly dust off of the crib? I was thinking about using a clean dampened cloth of mineral spirits. Unfortunately I don't have a tack cloth. What I have is a bag of clean rags that you can buy at big box stores, mineral spirits, some dust brushes and an air compressor. How do I remove all of the poly dust so my son doesn't eat it?
-
-
- 3 replies
- 2.9k views
-
-
I recently got a Fuji Semi-Pro 2 with a gravity gun. I wanted to have separate guns for lacquer and for "other" so I got a siphon style gun for my second. Is there any distinct advantage of one style over the other? The gravity gun has a 400ml cup and the siphon has a quart-sized cup. Would the extra capacity have an advantage with a particular finish? I think I'm going to end up shooting lacquer, maybe shellac, maybe poly or other varnish. If I move over to water borne finishes I'll probably get a third gun. Which gun would you use for which finish? And for bonus points, what kind of lacquer do you spray? I'm confused about the pre-cat and post-cat st…
-
-
- 10 replies
- 7k views
-
-
https://grandforks.craigslist.org/tls/5490858269.html Found this near me in my recent search for HVLP. Is this worth inquiring about? I can't find much information about it on the internet. It appears that Fuji has removed their old models from their website. I've never used HVLP or for that matter any sprayer.
-
- 3 replies
- 3k views
- 1 follower
-
-
I applied a water based wood filler (Crystal Lac) to my mahogany project yesterday. How long do I need to wait before I apply the spray on sealer? I read that I need to wait a while in order to allow the solvents in the sealer to dissipate?
-
-
- 6 replies
- 3.1k views
-
-
We are building a mobile bar for our son's new house. The top is a large slab of unknown wood, maybe pine, 4" thick. It is very dry and very old--was in storage at least 15 years. There are splinters, some of which have broken. Our planer won't handle it, so it was planed with a handheld power planer. I am getting it sanded down (to #220 so far). My feeling is that the wood needs moisture/oil to "feed" it, and if it were not going to be a bar top I would do a rubbed oil finish. But it will need to withstand wet glasses, etc. and I'm thinking a poly of some kind is needed. I have several questions. 1. Can I fill in the broken splinters with sawdust/glue, sand…
-
-
- 20 replies
- 3.4k views
-
-
I’m building a dresser for my daughter and she wants it to be blue. I’m building it out of solid poplar and birch plywood. In the past, I’ve only had ok results with painting furniture. I don’t have an airless sprayer, so I’ve only ever brushed/rolled paint. I do have an Earlex 5500 and would really like to spray this project. I spent a while last night reading up on possible ways to do this. Is dying an option? General finishes has a blue dye that I bought and I really like how it looks wiped on the poplar. Is there any chance of getting the plywood and birch to look similar? I am only using the birch plywood for the panels. I saw this produce mention…
-
-
- 6 replies
- 3.3k views
-
-
Refinishing kitchen table....Can I rectify my stain problem by using a wipe on shellac directly over the dry General Finishes Java Gel Stain (I have not put top coat on yet and stain has dried for 48 hours). Chain of events: Brought the unstripped leaf to local Ethan Allen store first, (where I bought kitchen table 14 yrs ago) refinisher thought it was solid wood. He also guessed it was maple or mahogany (it was very blonde once stripped, didn't look or feel like pine so my GUESS was maple). Because I didn't know for sure and had to work inside house, I stripped it with Citristrip (4 attempts later it worked). Let dry for 24 hours. Cleaned w/ mineral spirits, sit …
-
Been a woodworker for 40 years. I built kitchen cabinets with oak plywood, stained to match exterior finish because doors have glass fronts. Used Minwax Gunstock oil based stain. Let dry 2 days. Sprayed interior and exterior w satin Aguelente full strength using Fuji HVLP ...Nice hard finish! However 3 years later, there is still a chemical odor emanating from the cabinet that lingers on all the glassware stored in the cabinet giving any beverage a hint of the odor whether the glass is stored upside down or not... rinsing the glass before filling w beverage does work to eliminate it. I have tried leaving the cab door open for weeks at a time to 'offgas' the chemi…
-
-
- 23 replies
- 5.8k views
-
-
I tried to sand out a discoloration on s clean oak threshold. Should have known better. I stained the entire piece but the sanded area did not accept stain the same as the rest of the piece. So far I've tried just adding stain to the light area. Not sure if this will work. Help.
-
-
- 3 replies
- 2.8k views
-
-
Hi, I am new to this so please bear with me. I just built a living room set consisting of two end tables, a corner unit and a coffee table. The bottom frame is all metal ( solid bar and hollow tubing, ) and the tops are all 7/8" solid oak, which I purchased all dressed. I applied two coats of min wax dark walnut, 8 hours apart, and then applied a clear polyurethane over that. I botched the clear coating and used wet sand 600 grit to remove drips and blotches I had left. Then I tried to put a second coat of clear and just made a total mess.... lots of drips, and some dust showing thru. My daughter wanted the stain to be darker. I did my best to take off the whole 2…
-
- 5 replies
- 2.6k views
-
-
Im currently making a bubinga vanity top for a client, and I am interested in everyone's input on finishes in moist environments. Ive done a few vanities before and finished with minwax wipe on poly or ARS. I don't believe those clients have experienced any troubles with their vanities, or atleast I haven't heard complaints! Obviously bubinga is something I do not want to risk finish ignorance on. The wood species is inherently resistant to moisture, but do I need to go above and beyond with spar varnish like Marc suggests in his article? Im leaning towards standard wiping finish and warn the client to wipe up standing water(which you should be doing anyways!!), but want …
-
- 6 replies
- 3.8k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·