Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing

  1. Started by Lee Bussy,

    Can anyone recommend CitriStrip? Or am I stuck using Methyl-ethyl-Death based products?

    • 4 replies
    • 2.9k views
  2. Started by davewyo,

    I have a couple of respirators; a half and a full face. I don't use them very often for dust protection. I mostly use them with an organic vapor cartridge when applying finish. I see that a lot of people say they wear theirs all the time for dust protection. When using it for dust do you generally use a cartridge or do you just put in the particulate filter? And...If you use a cartridge infrequently, do you do anything special to get longer life from the carbon element which I assume is in most vapor cartridges? Back when I was spraying pesticides for a living I stored my half-spent cartridges in a ziplok to keep the cartridges from absorbing atmospheric moisture. Was tha…

    • 3 replies
    • 2.8k views
  3. Started by d8nk,

    So I have one that is stumping me. Red birch cabinets, 2 coats of shellac, now 1 coat oil based poly followed up with 2 coats of water based poly. I am getting these spots that look "dry" but coat after coat they stay the same. Sanding in-between coats obviously as well. Anyone had this issue? starting to get very concerned... Sent from my Nexus 5 using Tapatalk

  4. Started by boelkers,

    The other night I made a big mistake while applying polyurethane to some drawers I've been working on. I had my mask on and couldn't smell anything but once done I took the mask off I found the terrible smell of oil based polyurethane. I thought I had grabbed my can of water based polyurethane but apparently I accidentally switched them somewhere along the way when I was getting the cans out. So now the drawers have 1 coat of oil based poly on them and stink. These drawers will be used for clothes so I'm concerned that they will cause the clothing to stink too. I've been looking online for a next step to remedy the smell and I've seen it suggested to put down a second…

      • Like
    • 6 replies
    • 2.9k views
  5. Started by Cliff,

    So I made some trivets. And did a search online, which was stupid cause it pointed me right back here and told me to finish it with mineral oil. I did 8 or so last night. My question is, should I do more than one coat? And should I sand between coats like regular finish if I do more than one? They seem to look pretty good with one coat and considering what they will be used for - I figure one might be fine, but I don't mind doing more. Made from Walnut, fyi.

      • Like
    • 7 replies
    • 3k views
  6. Started by Cliff,

    Is there a secret to finishing a panel or a frame or something? I decided that since I wasn't in a hurry, i'd finish the top of a panel and the sides. Put 2nd coat on. 3rd day, I flip it over to the do the top of the panel and it had dripped around and pooled underneath. I had it sitting on saw horses. I'm surprised that it can even do that. I would have thought drips would fall right to the floor instead of going underneath the panel. Am I just sloppy and this will get better? I had the same problem with the frame I made a few months ago and on that, I had to sand it down and try to repair the finish. On this smoker cart panel, eh, it's going outside anyway so I doubt it…

      • Like
    • 23 replies
    • 3.4k views
  7. Started by Jerry_in_SD,

    about a year ago I posted a question regarding what happens to a breadboard end when a film finish is applied and the core inevitably expands and shrinks with the weather. WelI got my answer. I've attached a picture of the core / breadboard joint out toward the ends of the breadboard where only screws are holding the breadboard and where the core has the maximum movement ( center 4" was glued so no issue). I 'm trying to figure out a fix. This was a thick finish of 5 coats of sprayed EnduroVAR. I'm thinking about sanding down about 2 coats and re-spraying a think coat of EnduroVAR. Any other suggestions? What could prevent this in the future?

      • Like
    • 3 replies
    • 3.9k views
  8. Started by jg9522,

    A few WTO podcast episodes back, I remember Marc commenting that FWW magazine did a review of poly and Minwax beat out all others. I'm really not surprised, as I have been using Minwax poly for years, and have no complaints. I have just purchased some GF ArmR Seal, just because I've read so many good things about it. I haven't had the opportunity to try it out yet. But, while listening to a FWW STL podcast today, I see that Minwax is the sponsor of their podcast. Could that be the reason Minwax beat out ArmRSeal? Sent from my iPhone using Tapatalk

      • Like
    • 6 replies
    • 9.8k views
  9. Started by Tyler Sacks,

    Im trying to build a bench swing for a school project and I wanted to use white pine (primarily for cost/availability in various sizes at lowes) but I'm not entirely sure what finishes I can apply to the bench to protect it. I plan on building the stand out of pressure treated lumber, only the hanging bench will be constructed out of pine. any help would be greatly appreciated! attached is a sample photo I found online that I'm basing my project off of.

      • Like
    • 1 reply
    • 3.1k views
  10. Started by Chewie17,

    okay so if I buy an older handsaw I believe there was a lot of about 5 saws at a shop not too far from home that have been not well looked after from what I can tell, some have missing teeth some are bowed slightly and other are just very rough looking. this is somewhat 2 fold, is it worth buying these saws knowing that I would have to start from scratch and file the teeth flat and reset them, also this would be my first attempt at doing any of it. I didn't even take a good look at the handles however the other important info would be that they are panel saws from the look, they are a range of lengths to guess the average would be 26"? is the effort on a unknown bran…

      • Like
    • 12 replies
    • 3.4k views
  11. Started by Gunther15,

    Hello all, I am new to this sight and was wondering if I could get input from someone who know what they are doing. I am wanting a spray gun that will spray both stains and paint for my woodworking projects. I have been told that Fugi is the way to go with HVLP spraying systems. Another great option is an earlex but I was hoping to save a few pennies and not buy a whole HVLP System. I already have a Husky 8 Gal air compressor (Husky TA-2530B) that is rated at 4.0 SCFM @‌ 90 PSI. I was thinking about purchasing the Husky Gravity Feed HVLP Spray Gun ( H4840GHVSG ) but its air consumption rate is 4 CFM. Will this work with my compressor? I have also heard of some LVLP s…

  12. Started by fizch,

    I am looking to buy a new house that has a detached garage that I plan to use for a new workshop. I would like to add a room or closet for finishing my projects. Should I build my own paint booth? What materials would I need? Should I buy a paint booth? Do they make them that small? Thanks for your help.

      • Like
    • 5 replies
    • 3.1k views
  13. Started by Brendon_t,

    Hey guys, hoping some of our UK brethren could point me in a direction. My wife bought this buffet years and years ago. I sanded it down, burned through the veneer on the top do I stripped it all except for the back piece. Then coveted it with spar poly Anybody know what kind of wood, would have been used as a substrate wood for something like this? Btw, when tearing it apart, between the floor of one drawer and the bottom, was a folded up newspaper looks like a way to stop it from ratteling. The paper was from the outskirts of london, 1918.

    • 0 replies
    • 2.9k views
  14. Started by Michael,

    I recently acquired an older piano. I bought it for the sound, and now want to see if I can make it aesthetically match. It's a solid maple that was bleached, presumably 40 years ago. I have the original matching bench to test small areas on before I tackle the whole piano, but I wanted to see if anybody had tips for me first. I want to get out a few dents/scratches as well as get it back closer to the natural color, maybe a little bit darker. Am I wasting my time or is this a doable project?

  15. Started by Slmize,

    I just spent the last two day reading all 66 pages of the finishing forum to try to get my questions answered. I think I have a good idea of what I should do but would like some input to make sure I'm on the right track. My kids brought me a slab of sugar maple as a present and I'm going to make a buffet table for the dining room. My question concern knot and crack filling. From the posts I should fill the knots and cracks with dyed epoxy? As for the finish, danish oil with a wiping finish. My question is if this will be a good finish for something that will have dishes put on it? Also what is the best dye to add to my west systems epoxy? I've never made anything from a…

      • Like
    • 10 replies
    • 3.1k views
  16. I am currently building a sewing machine cabinet, (the sewing central ) from plans I purchased from Rockler woodworking. I am to the stage where I am about to put the two pedestals together, one will have drawers and one will not. I know I need to sand and finish the inside of the pedestal that is going to be seen that a given but do I need to sand finish the inside of the pedestal that house the drawers that will not be seen . what's the benefit to putting a finish on the inside other than a way to preserve the wood I don't plan to stain so I am only putting a clear protective finish on the outside. I still haven't decided on the type of finish I want so any input on th…

  17. Started by Firehawk,

    I made a 3 tiered walnut shelf for a friend and am using Arm-R-Seal satin on it. My question is how many coats is reccomended? I have 3 coats and wondered if that is adequate protection.

  18. Started by Alden,

    DO YOU RECOMMEND APPLYING LACQUER, AS A FINISH? (AFTER APPLYING MINWAX-GUNSTOCK WOOD FINISH) Thank-you!

  19. Guest
    Started by Guest,

    I am thinking of building an electric bass guitar, but before I get started, I wanted to figure out some difficulties in the process. I have a picture of the style I wanted to make attached. I would like to know how to go about staining the outer sections with a red stain without staining the middle sections. I am not sure if masking the area with tape after assembly would be sufficient, or if I might have to Pre-Stain each piece before glue up, and what disadvantages that might bring. I would also love suggestions on what timbers to use to get a similar grain pattern and base colour. Thankyou!

      • Like
    • 9 replies
    • 3k views
  20. Started by gmanmp,

    I getting near the finishing process for a Walnut farmhouse table. I have researched dozens of sites to be sure i dont mess this up and thought i would ask you finish experts' opinion. Here is what i want to do: 1. After sanding down to 240 grit, 3-4 coats of watco danish oil with 400 grit wet/dry sand paper during initial coat. ( I have read this paste will fill the pores nicely) Subsequent coats will only be sanded after it has dried overnight using 0000 steel wool. 2. 1-2 coats of Bulls Eye Amber shellac. Now i know most will recommend using only dewaxed shellac; however, i saw a video Marc where tried this and has not had any problems with regular shellac (…

    • 11 replies
    • 19.3k views
  21. Started by Nick D Edge,

    Does anyone have any suggestions about what dye or combination of dyes to use on maple to simulate butternut?

  22. Started by Bart,

    I've made an outdoor table out of Burmese teak which has beautiful grain and color, grays and brown with orangy/pink streaks. After final sanding, I applied satin wipe on poly, my go-to finish for walnut. However, it's given the table a yellowish look which is not great. Anybody have any better ideas? I could try a teak oil, but have read some negative feedback on that too, mold etc. I've tried to attach pictures, hope you can see it. First one is rough sanded, before final 240 grit, second one is after 1 coat of wipe on poly. regards, Bart

    • 7 replies
    • 3.2k views
  23. Started by ajkezele,

    Looking for suggestions on products to use for a pocket knife I'm making as a Christmas gift. It is really simple project but I want to make sure the finish holds up well and of course looks great. Any suggestions would be greatly appreciated. Thanks!

      • Like
    • 16 replies
    • 4k views
  24. Started by Fabbr,

    I'm super new to wood working and I plan on building an outside BBQ table. It will be covered when not used but I need to make sure is sealed against water and sun. I want to use pine because it's cheap but I want to stain it dark and then seal it. Many suggestions on the products I should use? I read about marine product Epifane but they don't offer stain just seal. Thank you

  25. Started by Jim DaddyO,

    I have seen variations of this finish all over. I don't think the ratios are overly critical. Not a hard wearing finish, but works great in lots of applications. I think I may have found my "go to" finish. If you replace the BLO with mineral oil, it is food safe.

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.