Finishing
2,922 topics in this forum
-
Hi Everyone, I'm new to this group and to woodworking. I'm in the process of finishing my first "real" furniture project. I'm using walnut to create a media cabinet. I bought the walnut from Owl Hardwood. I believe it's kiln dried. The project was going great until the finishing phase. Here's what I've done: a light layer of boiled linseed oil (BLO), followed by dewaxed shellac (Seal Coat from Zinsser), then one layer of General Finishes Arm R Seal satin - light sanding, then another layer of Arm R Seal satin. This is where the problem came in. The second layer produced a horrible plastic appearance. I went from a nice clear, grain showing finish to something that looked …
-
-
- 28 replies
- 31.4k views
-
-
I refinished our kitchen table. For the finish I used Minwax water base Polycrylic because I'm pretty new at applying poly finishes and heard this was easy to apply. And it was, went on beautifully. Followed directions to a T. Did 5 coats. Let it cure for 5 days before bringing it up for use. It got bumped on the way up the stairs and looked like it had some paint transfer so I scratched it off but it was the polycrylic and it scratched right off. Within 24 hours it got another scratch and the poly came right off again. Did I do something wrong? Is it just a crappy finish? I know it should not just scratch off. The wood doesn't get damaged or scratched, the poly just scr…
-
- 15 replies
- 26.5k views
-
-
I was putting Arm r seal on 10 Christmas presents and grabbed a cutting board by mistake and slapped finish on it too. I'm thinking I need to sand it back down, or do I?
-
- 5 replies
- 3k views
-
-
Try and paint kitchen cabinets to look better than the original hickory ... The cabinets in my house are hickory that had a really cheap, crappy finish that started to fail after a few years... Water stains, complete lifting, etc; they look bad.. I like the hickory contrast when they were new, but am too lazy to do a total strip and refinish. I do enough of that at work, last thing I want to do in my "off time" is more stripping ... anyway, decided to take the simple route and paint the cabinets. Looked over in my cabinet of goodies and saw a few different glaze colors.. Hmmm... What would this look like? One thing led to another (a Bombay May have had something t…
-
-
- 12 replies
- 3.4k views
-
-
My wife wants me to build a book shelf for my daughters room that matches her preexisting furniture. I went to sherwin williams and asked if they sold color matched dye because I have heard of other people going their for good quality dye. The lady working there said that they don't have dye, but they do color match stain. Is it possible that she was mistaken? I have been to a couple sherwin williams around me, and they all say that they don't sell dye, and can't order it in. Just seems strange to me when I have seen a bunch of other people getting quality dye from there.
-
In June I finished building an endtable. To finish it I used 4 coats of Shellac. After sanding it smooth I applied 3 coats of General Finishes Arm-R-Seal. Now I have noticed that the finish appears to be bubbling up in places. It looks like the table has a rash. Are there any theories as to what is happening? The table has been kept in at about 77 degrees until last thursday when the AC broke. Since then it has been bathed in the humidity of Virginia. Any advice would be helpful.
-
- 7 replies
- 3.2k views
-
-
Can anyone recommend a brand and color to match this oak door? I bought and used "golden oak", brand x and this built in definitely does NOT match the door or the store sample.
-
-
- 6 replies
- 3.1k views
-
-
I watched some video a while back where a guy took a torch to a piece. Then he scraped and sanded the char off and he had a really great depth of color. Does anyone know what the name of this type of fishing process might be called so I can learn more about it?
-
-
- 22 replies
- 33.9k views
-
-
i just started working with epoxy and am interested in buying it in larger quantities? Any help on brand and type of epoxy would be great! Thanks! I am using it for filling knots in wood or coating bar/table tops. Etc... Also where to order it from
-
-
- 5 replies
- 2.9k views
-
-
I applied Minwax clear gloss polyurethane, an oil based interior product, to a wooden chair a few months ago. Now we want to put it on the porch where it will be in full sun. Is there some clear gloss product that I apply on top of the existing poly to protect it from UV? Thanks
-
- 4 replies
- 3.1k views
-
-
So I'm getting pretty good at at least cutting pieces to size, need to work on getting tighter joints, but where most of my projects fail is that I get impatient to start assembling them that I skimp on finish. So I looked at Tauton's complete guide to finishing, but what I'm looking for is more of finish prep than actual finish. Once you have a piece cut to the proper size (or over a little in some cases) what steps do you take to prepare it for finishing? An example is that I just finished a piece of plywood shelf for a closet, and after cutting to size, I sanded with 80 grit, followed by 120 grit, followed by 220 grit in preparation for painting it with plain interior …
-
-
- 6 replies
- 2.9k views
-
-
Can someone recommend a professional in Michigan that is experienced with epoxy to seal kitchen counters and bar top? I have reclaimed bowling alley countertops and I want to get them sealed. I've previously used epoxy resin for smaller projects like fireplace mantels, but I really want someone with more experience to do my counters. Any help is appreciated. Thank you.
-
- 1 reply
- 3.6k views
-
-
I am finishing a cherry shelf unit and after sanding and applying a waterborne blotch control I have green specks and some green areas on most of the shelf pieces. They are not big enough to show up in a picture but they are clearly visible to the eye. I suspect a reaction between the sandpaper substrate but I'm not sure. I do not know what the paper is, it was some given to me by 3M 20 years ago. Does my suspicion sound right?
-
-
- 18 replies
- 3.8k views
-
-
Hey everyone, Comes the time to apply some wax and I have been left a bit perplexed. My wax finish is more in line with a traditional Sam Maloof recipe sans tung, 80% linseed/ 20% wax. I am applying it similarly, after my top coat is dry, burnishing with 0000 steel wool, a good heated rub onto the surface, coming back the next day with a dry cotton rag. The results seem great, surface is slick with a soft sheen. But I am wondering what the difference would be by using a non-drying oil, such as mineral oil + wax instead of the drying oil? It seems that the latter process is in line with most articles online for rubbing out. Maybe the Sam Maloof method does something here t…
-
- 4 replies
- 3k views
-
-
Just made this out of some scrap material (cedar fence boards) because I wanted to try this painting technique. There are two coats of paint, different colors, sanding between coats for effect. The final coat was some Jacobean stain I had. It turned out exactly as I was hoping. There's a smaller one too. This one is a serving tray and the other is just a storage container. So, would you put on a topcoat and if so, what?
-
-
- 10 replies
- 3.2k views
-
-
I spray outdoors, but I hate having to wait for calm day/dry day when I need something done. Just wondering what everyone else does for spraying. I have the space and desire to build a dedicated spray area in my basement, but need more research before deciding to build something (H20 finish only). So lets hear what the community does!
-
-
- 23 replies
- 4.4k views
-
-
Do you suffer from this affliction as well? No matter what finish I use, I always seem to want to apply one more coat. When spraying waterborne with the HVLP, I always think three will do, but I normally just have to spray that extra coat. When applying wipe on poly, I always go a few coats extra. On my last tabletop, I had 7 coats, and the base had 5. Any cure for this disease?!?
-
-
- 7 replies
- 2.9k views
-
-
I have an antique pine desk that I'm repurposing into a bathroom vanity. I plan to apply a CPES followed by Arm-R-Seal topcoat. However, before all that I need to clean the wood. Its a salvaged piece that's a bit beat up. I don't want to strip it and restain it - I like the salvaged look. But what should I use to clean this thing up before applying the sealant and topcoat?
-
-
- 1 reply
- 3k views
-
-
I'm building two 4x8 sliding barn doors out of reclaimed redwood. These barn doors will be used as separators in a bathroom/laundry room so they will be exposed to steam, humidity changes, and occasional splashes of water. I've had all the wood cut, planed, and sanded into the pieces that I need. Now I need to waterproof these doors and then assemble them. What products and process would I use to maintain the stunning beauty of this wood while protecting it. Ultimately I want the finish to be a satin or semi-gloss look. THANKS!
-
- 5 replies
- 3.1k views
-
-
So with this current speargun build being my first build since I started really woodworking, I'm starting to think about other finishing options that most spearo's don't know of. Specifically, thinking about using GF salad bowl finish under teak oil rather than a thick epoxy coat. There are really 2 universally accepted finishing methods for Wood guns. 1) slow set epoxy (that you cannot use on the enclosed rail due to the thickness) and 2) liberal coats of teak oil maintained often. I'm going with teak oil but wondered about first coating the whole gun with salad bowl finish first for more protection. I use GF salad bowl finish on my cutting boards and it seals out…
-
- 26 replies
- 10.7k views
-
-
I recently redid a old oak bedroom furniture. It was originally finished with a milk stain. Because of this when I tried to get off the stain it left a little stain in the pores. I then painted it,I used 2 coats of zinsser primer then 2 coats of Valspar latex paint. I wanted to see a wood grain so I mixed 3 parts Valspar clear mixing glaze to one part brunt umber and used a wood graining tool to get the effect. It worked great. Well almost, I used all water based products and the I wanted to put a polycrylic on to protect it, I tried to apply the minwax water based polycrylic and it was cloudy and some spots blotched a bit. I Was told after the fact that I can not use an…
-
- 9 replies
- 26.9k views
-
-
In my quest to get a warm oil look with walnut using waterbornes I've tried several recipes. I know I'll never get the Waterlox look I love using waterbornes but I would like to get close. Below are some of my test boards. Wide board - air dried with thinned oil poly followed by waterborne poly top coats. The oil poly warmed it up some but not enough for my tastes. Middle board - kiln/steam dried with Waterlox original followed by Waterlox satin. This is the look I'm going for. Long board - air dried with Lockwood American walnut water dye followed by waterborne poly. It actually warmed it up nicely but too strong of a mix for my liking. I have more test boards currently…
-
-
- 26 replies
- 16.6k views
-
-
This forum is very informative! I was recently given a burled walnut bed and matching dresser with a granite top and a framed mirror above that. Due to a fragment of the manufacturers "sticker", I was able to find out it had been made in Milwaukee, WI in 1882. The interiors of drawers are completely finished. The entire set is all walnut and my question is this: In some areas the finish is completely off on the exposed pieces of wood. I plan to use this furniture and am wondering if I should just clean it all with Murphys oil soap and just leave it alone? Or do I strip the whole thing and re -shellac (which I have never used before)? Thanks.
-
- 8 replies
- 3.2k views
-
-
I pre-finished the interior surfaces of a small cabinet I am building with Arm-r-seal. I now have it assembled and am ready to finish the exterior surfaces. Is there anything I should be careful of where the pre-finished surfaces meet the raw wood - i.e. will there be a noticeable line/sag where the fresh Arm-r-seal meets the old Arm-r-seal on the interior surfaces? The corners have a radius so there is not a sharp line breaking the surfaces. Thanks in advance!
-
-
- 1 reply
- 2.7k views
-
-
I am putting up a shelf that is walnut and still has the bark on some of the edge which my wife wants to keep is there anything I should do to this ( finish wise )as it will be in the house thanks
-
-
- 3 replies
- 2.8k views
-
Who's Online (See full list)
- There are no registered users currently online
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·