Finishing
2,922 topics in this forum
-
I've been looking to purchase my first spray system. Recently I've been looking at the Earlex HV6003PUS HVLP SprayPort. Does anyone have a review of this product? In the past I've been taking my larger projects to another shop and have been paying someone else to spray for me. I've got a couple larger projects coming up this fall and would rather invest that money into my own equipment. Thanks in advance. Bill
-
-
- 8 replies
- 6.1k views
-
-
There’s no knowledge more valuable than a hard-earned lesson – except maybe someone else’s hard-earned lesson... This seems to be lessons-learned week for me, so I might as well pass them along as they come... Don’t problems come in threes? Number two for the week: Finished my garden planter project... QSWO, DominoXL, CPES, Epifanes. Turned-out rather well, if I do say do myself... Pre-finished all components with two coats of CPES, assembled, pinned all the Dominos, sanded all surfaces, ready for a final coat of CPES to protect the wood and five coats of high-solids-UV marine varnish to protect the CPES... Laid-down a couple of those disposable tarps to protect the deck…
-
- 7 replies
- 3.2k views
-
-
I am building a combo clock/passive iPhone amplifier out of cherry. My first project with this wood. I have previously done work with Jatoba using Danish Oil that I really liked and mahogany projects with Danish oil and some with Tung oil. For the mahogany I also added a touch of red dye to the filler. As this is coming together I wanted to get some ideas. I am leaning Tung oil at this point. Thanks for ideas. I will provide pics. Sent from my iPhone using Tapatalk
-
-
- 2 replies
- 2.9k views
-
-
First of my newb projects that I'm experimenting with dye and I'm seeing about 10 different ways to potentially accomplish what i'm looking for. I want to get a super smooth finish on ash, based on my experimenting I'm realizing I'm going to need a grain filler to get the result I want. I have Behlen NGR dye and plan to use a couple of coats of that then Shellac then ARS. I want the wood all the same color, so I'm looking for a grain filler that I can tint with the dye to get the same color. What would you recommend that isn't water based? 2nd at what point would you use the grain filler? I'm thinking in-between the dye and shellac since I'm not trying to achieve a secon…
-
-
- 7 replies
- 3.6k views
-
-
I'm soon to be putting an oil based finish on a project in my garage. I live in southern Louisiana so as you can imagine the humidity is pretty high at all times. We are also currently reaching temperatures at and above 100 degrees. I would think that the high humidity would cause the finish to cure slower, but the heat would cause it to cure faster and cancel each other out. I'm by no means an expert on finishes nor weather, so I'm expecting to be way off. This will be my first finish job, so any advice would be helpful and appreciated.
-
-
- 9 replies
- 3k views
-
-
Okay so I am having a hell of time finding it but around the beginning of the year I found an Online guide that showed different wood types with samples of different sealers on it like Linseed oil, tung oil, orange shellac and etc. Does anyone have the link to that? Thanks.
-
- 1 reply
- 2.7k views
-
-
I purchased 2 quarts of Enduro Var Gloss about 3 weeks apart.The new can was a bright pink color but what was left if the old can was a much paler brownish pink color. I don't remember what the first can looked like when I first opened it. Has anyone else seen this? Is it normal for the color to change after the can has been opened, is the older can still good?
-
- 3 replies
- 3.7k views
-
-
I am building a bedroom suit out of Ash. Was wondering what the best finish would be to create a Satin type finish, but yet will resist scratching and doesn't have a "tacky" feel that tends to collect a lot of dust. (The wood will be stained to a mid-light oak first) What are your recommendations.
-
-
- 9 replies
- 3.1k views
-
-
hi I'm refinishing an old coffee table that we have and sanded it down with 120 grit to remove the old finish then lightly with 220 before staining. I applied the minwax pre-stainer let sit for 15 minutes then wiped it off and proceeded to use minwax ebony gel stain. I applied the stain with a brush, let it sit for 3 minutes then wiped it off with a towel(like a hand towel). after waiting for 24 hrs, I came back and saw that there were either brush strokes or towel streaks from the wiping. some of them were also a milky color and looked like a hologram. anyways to try and fix it, I applied a second coat and waited 24 hrs and then tried lightly sanding with 320 grit sandpa…
-
-
- 8 replies
- 21k views
-
-
I'm running out of old t shirts to cut up and use. Does anyone have any sources for decent cotton rags that aren't cut up from tshirts that were recycled. Most of the ones I've found online have reviews of armpit stained pieces of cloth or ends of shirts with lace. Any favorite rags out there?
-
-
- 10 replies
- 3.1k views
-
-
I am very new to finishing so looking for some advice... I have a walnut table that will be used in the kitchen with 3 messy kids so it will get lots of use. After reading posts and trying a few finishes, I decided to go with Danish Oil in Dark Walnut. I've put on 3 coats with at least 24 hours of drying between - Wet sanding the first coat only. I am happy with the color - it feels very smooth to the touch. Should I stop here or add another coat? So now what? I am not sure if I should use a wipe on poly or wax finish for maximum protection. I don't want a glossy finish - I prefer the satin look. Thanks so much for the advice!
-
- 9 replies
- 15.5k views
-
-
I am currently working on a cribbage board project that was in a recent issue of WOOD magazine. In the article they used maple and cherry and finished it with spray-on lacquer. It was my understanding that cherry should be conditioned to prevent blotching. Is that still true when using spray-on lacquer? I decided to go with rosewood and cherry. What would you guys recommend for a finish? I have sealcoat + Armour Seal or is spray-on lacquer a better idea. Also, does rosewood need to be wiped with a solvent prior to finishing to remove the natural oil? Thanks, Chris.
-
- 2 replies
- 2.9k views
-
-
I will be building some bedroom furniture using Utile (also called Sapo). It is a mahogany substitute and used quite a lot in Europe. I prefer a natural wood finish like Arm-R-Seal but my wife would like to stain or dye to bring out more of the dark grain and ribboning. Has anyone used this wood and what is a good finish that brings out the grain? Any recommendations of where to look for information? I have searched on line but haven't found much. Thanks.
-
-
- 18 replies
- 8.4k views
-
-
I have just finished sanding a new mask that I carved and want to seal the wood before I paint it so the wood won't absorb the water from my paint and become rough again. Anyone have any suggestion on what to use?
-
-
- 6 replies
- 2.9k views
-
-
I'm finishing a walnut bar top and plan on using GF arm-r-seal. I went to pore fill the surface first after sanding up to 180. I wet sanded with Watco Danish oil per suggestions on one of the wood whisperer early vids on refinishing. After 24 hours the surface wasn't dry and now I've waited 4 days. Thought it was dry tonight and went to dry sand it starting with 220. It appears areas are still not dry as 220 would do nothing and back to 180 creating a 'gummy' mess in a few areas. Is that indication that its still not dried? Its looking like I'm going to have to start again at a lot lower grit and basically get below the pores that were filled (start over). Or should I gi…
-
-
- 7 replies
- 6k views
-
-
I am building my second hollow wooden surfboard and I'm looking for a way to seal the wood. My first board got a polyester resin and fiberglass finish, which works fine but its just to damn toxic for my taste(literally). Epoxy would work great but $80-$120 per gallon makes it cost prohibitive. I'm wondering if say polyurethane or a thompsons water seal is actually waterproof or just resistant. While they may keep water off the wood, can they hold up in a marine environment where they will be submerged in salt water for hours at a time.
-
- 15 replies
- 5.8k views
-
-
Have a pine bed that has been sanded down to bare wood, and has had three thin coats of Boiled Linseed Oil applied. Is there a low sheen finish like water based satin polyurethane, that can be applied over the BLO.
-
- 3 replies
- 4.5k views
-
-
I'm building a, "Fake old" factory cart coffee table. It is just pine, stained to look more like a hardwood. I applied a couple of thick coats of water based stain using a rag. I didn't like the aging scrapes that I did on the ends of the cart to make it look well used, and sanded them off and redid them. That left a 3 inch section of new raw sanded wood that was sanded smooth, but with only 100 grit. The rest of the top had not been sanded to leave it rougher looking. While sanding the ends, I had sanded the edge between the raw and the previously stained overlapping somewhat. When I stained it, I thought it looked fine. The difference in color between the newly sanded…
-
- 4 replies
- 4k views
-
-
In my attempt to match my pine windows with my alder trim, I conditioned a sample board with #1 shellac, coated with semi transparent stain, then rubbed in dark wax. It was a perfect match to the stained trim. SO...I conditioned all my pine windows and now the semi transparent stain just will not "stick". Any ideas on how to get this water based stain to do the same thing it did on my sample board?
-
-
- 5 replies
- 3.3k views
-
-
I built this trailer for a friend. Used Flat sawn white oak stained it golden oak. He is painting the up rights . When he clear coats the paint will he be able to use an automotive clear coat the wood also?
-
- 3 replies
- 2.8k views
-
-
http://www.lowes.com/pd_105568-47120-SGY-AIR160TZ___?productId=50246671&pl=1&Ntt=kobalt+spray+gun Seems to be in the "too good to be true" market. Kobalt makes some pretty decent stuff, Im probably gonna pick this up. Any one have one of these? I'll probably grab the set tomorrow, and let you guys know how it goes. Would be quite the boon in the "cheap" spray gun market I would think.
-
- 1 reply
- 3.5k views
-
-
I built all new upper cabinets in the kitchen, refinished lowers and built new doors and drawers for all the cabinets. The door frames are solid maple with a 1/4" maple plywood panel. They were finished with an oil based general finishes stain and then 4 coats of minwax poly. A couple of the doors are showing some weird mark on the bottom of the plywood panel. All are lower doors which makes me think water damage but one is on the island which isn't even close to the sink. Any ideas?
-
-
- 6 replies
- 2.9k views
-
-
I have a table, family piece (described in other thread) that has a veneer oak top, The table itself is early 1900's, perhaps 1910-1920 range. The veneer has come pieces missing, typical chips. If I want to repair this, is replacing the veneer the only/best way? I assume I can count on this being hide clue and coming up fairly easily with a chisel type tool?
-
- 5 replies
- 3k views
-
-
I have a 5 inch random orbit sander and am looking to go for a high-gloss lacquer finish. I see one way is to use 1000+ grit sand paper, and inherited a pack of 6" Abrasion discs. Will I get good results from using the 6" or should I spring for the 5" online? Thanks much in advance.
-
- 5 replies
- 11.6k views
-
-
I just finished a piece with a GF gel stain, and I plan on putting a couple (thin) coats of GF gel top coat on once the stain is dry. Should I be wet sanding the gel stain before I put the top coat on, and if so, what should I be using as lubricant? If it helps, it is a small bookcase from QSWO.
-
- 2 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·