Finishing
2,922 topics in this forum
-
Good Evening, I've had such good luck asking previous questions I figure I'd try another one. I'm building an office desk out of walnut, one side live edge the other just plain. I was going to use Arm R Seal again as I used that on a previous desk of various hardwoods and it turned out great. I however am open to suggestions. What have others used? Pro's Con's? etc.. Thanks!
-
-
- 12 replies
- 3.1k views
-
-
Hello everyone! I am brand new here and have little experience in the wood finishing department. I stained some mahogany doors yesterday and not sure of the results. I did not use a conditioner and thinking I should have as there is quite a color contrast in some areas. I hit any rough spots with 120 grit by hand, then a 220 grit sanding sponge over everything. Minwax espresso oil stain brushed on that I let soak in for a bit before wiping with a rag. Is this just the way mahogany takes stain, or did I screw up somewhere? Thanks all, Jesse
-
-
- 5 replies
- 2.9k views
-
-
I built a table for a client a couple months ago. I advised him on putting glass on the top. The glass wasn't put on on time and he put his signature in the cherry. I put two coats of shellac and two coats of tru oil on top of that. My question is would it damage the finish if I did the iron trick to bring the wood back up? I was thinking about testing it on my own but wanted your opinions before I waste my time. (Iron trick-when you use the steam from the iron to fix the compressed wood fibers)
-
- 2 replies
- 3k views
-
-
I am absolutely a newbie with wood refinishing of all kinds. I am trying to refinish a solid oak table (and benches) my dad made years ago. I sanded it down with 120 grit sandpaper. After sanding, I applied a quick, light coat of mineral spirits as suggested by the General Finishes tutorial video to reduce lap marks on a large surface. I am using General Finishes gel stain in Brown Mahogany. I applied my first coat of stain with a foam brush, and then wiped off the excess stain with a shop towel. The whole tabletop looks TERRIBLY blotchy. See the attached pictures: the lighter table is after 1 coat, the darker table is after 2. The table is not covered in lap marks o…
-
-
- 10 replies
- 22.6k views
-
-
I am a relatively new woodworker and would like some wood finishing advice on a project. The project is being made from Ash and includes a hand carved company logo. I would like to use an Artisan dye on the carved logo, without it bleeding into or affecting the wood around the carving. The Artisan dye I've chosen contains Methyl Alcohol, Diethylene Glycol Monoethyl Ether and Shellac. If I spray or wipe a coat of poly into the carved area prior to using the dye, with this keep the dye from spreading into the rest of the work piece? Any ideas or suggestions would be helpful. Thank you.
-
- 7 replies
- 3k views
-
-
Hello, I refinished an oak dining table. However, on patch would not take the stain. My dad tried to help suggesting I should sand against the grain. Also he tried to strip it with a razor blade. Anyhow this is what it looks like now. The rest of the table looks great. Is there anything I can do to fix this? I am using miniwax stain in weathered oak.
-
-
- 8 replies
- 3k views
-
-
I'm using Zinsser Seal Coat to lock down my Transtint Dye stain before applying lacquer and I'm intermittently having problems. It seems that if I wipe on the Seal Coat (on small projects or test boards) I don't have any problems however if I spray it on the dye seems to be bleeding into the Seal Coat. The first time it happened I noticed that the mantel I was spraying continued to have that dull look that dye stains have even after the seal coat was applied and had dried. When I touched a side still wet with the seal coat it was apparent that the dye had bled into the seal coat, my finger had brown tinted seal coat on it. I decided I had sprayed it on too thick and tried…
-
- 2 replies
- 5.3k views
-
-
Hi - Is there any need to sand between coats of finishes that "melt" into each other like shellac (and lacquer). It seems to me like you could just sand the final coat since there is no need to rough up the surface so the next one will stick to it as you do with polyurethane. Cheers, Brian
-
-
- 4 replies
- 11k views
-
-
Okay this is my first time doing this, I thought I sanded this down enough but the stain did not take to certain areas! Help! Should I resand? Did I ruin this? Massive mess, and I'm an obvious newbie! Eeeek the wood is pine, so I know this is a soft wood.
-
-
- 17 replies
- 3.4k views
-
-
Working on restoring a musical instrument that features a peice of Mahogany, that when sanded thoroughly is a copper color. I plan on using a vinyl sanding sealer that contains Nitrocellulose and a top coat lacquer containing the same, which being Amber in nature, will most certainly combine with the natural color of the Mahogany and become a brownish color. In order to avoid this overpowering the desired color, is there a predictive software that will calculate the tint color needed to produce the hue that I want? Purple is the end goal, and I know it's possible because I have seen translucent purple finished guitars made from Mahogany...or would it be better to use a pr…
-
-
- 5 replies
- 2.8k views
-
-
-
I would like some suggestions on finishing this coffee table. It is made of Elm, I would like to darken the grain slightly but (always a but) there are walnut and mahogany Dutchmen and a walnut leg that I don't think will look good if stained. I have considered oil with shellac sealer and then a waterborne top coat for durability.
-
-
- 31 replies
- 7.1k views
-
-
I believed I screwed up again! I attempted to apply minwax wipe on poly over a cherry bookcase top that I had applied Danish oil about 2 weeks ago. I had forgotten why I stopped using wipe on poly products because no matter how I try I always get streaks. Well, I got them again with one light coat applied. My question is will they always be there or can I attempt to use my HLVP Fuji sprayer gun and spray a couple coats of the stuff over the existing layer? I am reluctant to sand even with 800 paper because I know there will scuff marks. Not trying to reach perfection but do want to cover the streaks if possible. I gave up using wipe on with projects that have more than 24…
-
-
- 20 replies
- 15.9k views
-
-
What is your favorite way of emphasizing the grain pattern in Cherry? T%hnx.
-
- 4 replies
- 3.3k views
- 1 follower
-
-
Kind of finish related. I'm hoping to make a few sets of cufflinks like these using different color leads to go with different ties. The question is once formed, if using clear epoxy, can you Sand it back high enough to see through it again? Whenever I've sanded epoxy, it status cloudy.
-
-
- 7 replies
- 2.9k views
-
-
Hi there, so I'm building a display case made to house match box cars and need to know how to finish it. By how to I mean should I pre finish or not. There will be 10 shelves that are 1/4 thick spaced about 2 . 5 in apart. The back will go on last, as it will be felt linned. I just got an hvlp conversation gun and have used it on one other project with decent results. Would the proximity of the shelves cause problems when spraying. I would rather not pre finish if I can help it. It just seems like a pita. Any tips or advice would be greatly appreciated. Thanks
-
- 5 replies
- 3k views
-
-
Hello all. I am in the process of finishing up my version of the Rustic Outdoor Table that Mark built. As its my first project of this scale I went with construction lumber instead of something "nicer". I have seen 2 of his videos regarding finishing outdoor furniture in Arizona(where I am as well) and am looking for advice on which one would be best. In the table video he uses teak oil, which as he states I would need to reapply every year or so. In another video he refinishes his parents door with a home made blend. I am willing to try that application if it will yield a superior product, but wanted the advice of the forum on how you guys would proceed. Thank…
-
- 12 replies
- 3.2k views
-
-
So I'm finishing a table and the only way I could match the color they wanted is with a general finishes dye stain mixture, shellac seal coat thinned a little another stain color and then the poly. This method was pretty easy on my two test pieces I did but on the large table pieces the shellac is bleeding the dye around a lot. I knew it would pull some of the color but this is leaving distinct start and stop lines. The table is 8' by 40" so just running a smooth brush stroke is easier said than done. Am I missing something or should I just have sprayed all these coats and not messed with it? Thanks! Sent from my iPhone using Tapatalk
-
- 11 replies
- 6.9k views
-
-
I am making a few rustic style coolers out of cedar fence boards (see pic for example). I would like to spray a sealer coat on them instead of finishing by hand. I prefer a water based product and have used Hydrocoat on a couple of small projects before, but not sure if that would be a good choice for this. What do you guys recommend?
-
- 7 replies
- 2.7k views
-
-
Well,I am coming down the home stretch of my bookcase project using cherry ply for the sides and shelves and cherry boards for the top that is trimmed in walnut. I used Danish oil as the customer request a oil finish. After the third coat I am not happy with the uneven sheen of the sides and shelves but can live with the top. I do not want to apply anymore Danish oil as I don't think it is going to ever get a uniform sheen type of finish. Not sure how to fix the problem but am leaning toward spraying on a couple coats of ARS or even wipe on polyp about a week or so. Do you think that a spray or wipe on film finish will even out the uneven finish look? I attached a couple …
-
- 13 replies
- 8.2k views
-
-
I have a stained and varnished or polyurethaned front door that catches some western sun. After 8 years, the finish and stain are gone. I recently saw a video where Marc Spagnuolo recommended a homemade oil/marine varnish blend for desert climate with yearly touch ups. I think his recommendation was primarily for the heat. I live in the San Diego area but wondered if the same idea would help with my problem. I don't have the heat but have the sun. Any suggestions? I prefer, if I can, to have a stained and finished exterior to match the interior. Thank you.
-
- 0 replies
- 3k views
-
-
My son and I have been building his dream guitar and will soon be starting on the finishing. I have been spraying finishes for several years now but never worked with pre-cat before, does anyone know how spraying it compares to other finishes, I just bought a Earlex as my other gun had seen its better days. I almost always spray water based as its safer with my setup but am willing to spray about anything if it gives the guitar a more durable finish (and can be polished). The other finish I'm considering is GF's Enduro-var. Any thoughts?? Thank you and God bless! Nate
-
- 3 replies
- 3k views
-
-
I'm using ArmrSeal to finish a bandsaw box made out of Alder. The wood is so dry that even though I flooded it three times in under a minute, every bit soaked in and the wood looks like its already dry. Didn't have to wipe anything off and its dry to the touch. I spent more time getting gloves on and stirring the finish in the can that I did applying it. Something tells me not to keep this wood anywhere near an open flame. Adam
-
-
- 6 replies
- 2.9k views
- 1 follower
-
-
A few year back, I bought the Rockler HVLP sprayer. I have yet to use it. My hesitation comes from the lack of knowledge and experience in this finishing method. Can one use off the shelf finishes and what are the headaches as far as cleaning the equipment between sprays? The system that I have is all in one (no air compressor needed. Is there anyone here using this system and if so some guidance would be welcome....
-
-
- 6 replies
- 3.6k views
-
-
I am working on a keepsake box. I am using Arm-R-Seal and will use a hand rubbed high gloss finish on the top. I have done a finish board and am noticing something that could be a problem. Each coat of finish dries with a slight raised ridge along the edge of the piece. For the first couple of coats it was easy enough to sand it down flush with 400 grit. But it reappears with each coat. I am concerned that for the last coat when I want to use 1000 grit to start my finishing process that I it will be much more difficult to remove the ridge. How to I minimize this ridge and still put down a thick enough coat to allow for the final finishing process? Will a slight rou…
-
- 3 replies
- 2.8k views
- 1 follower
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·