Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing

  1. Started by amateur eric,

    So I've made a few projects here and there, but I've always used rattle can polyurethane for finishing. My new project is to make an Army NCO sword display for the sword I was just gifted recently. I'm wanting to put an American flag in the back and put my company logo in the front and have foam in between to hold the sword. I am, however interested in not doing a rattle van poly for this. I'm thinking of doing an oil finish over it all? There will be laser engraving for the stars of the flag and the company logo and engineer motto. Basically this... Will be placed onto and cut out of this... This is a basic sword display, but for the back layer like I said would …

    • 4 replies
    • 2.9k views
  2. Started by Seth Clayton,

    Hi all! What's the best/quickest/easiest way to strip off old paint from outdoor projects that need freshening up? This isn't fine furniture, just some 4x4's and 2x4's. I saw the Wagner Paint Eater at Lowe's. Is that worth getting? I have a plain Bosch ROS, so I'm not sure I really need another tool. Sent from my iPhone using Tapatalk

    • 4 replies
    • 2.7k views
  3. What's the best finish coat to use on wood furniture that will be indoors, but subject to freezing temps over the winter months in my cabin.

      • Like
    • 7 replies
    • 3.1k views
  4. Started by Curtis,

    I am starting to prefinish all the panels for two sets of douglas fir exterior carriage doors. I am using epifanes mv. Should I finish the tongue of the panel and inside groove on the rail/stile that it floats in, or leave those unfinished. I am going to use moulding that goes around exterior of panel with some flexible caulk for sealing. Just seeing if I finish all the panels first then cut tongue around the edge or other way around. Thanks! Curt

      • Like
    • 4 replies
    • 2.9k views
  5. Started by asousa,

    I recently started refinishing an old buffet table. The top is veneer, which was water damaged and very lifted and cracked in one area. As I chipped away at the veneer, I noticed a residue on the bottom layer of wood that resembled dirt. Brown and slightly black in color. Would this be mold dust, considering the water damage? The buffet has been in someones storage unit so I'm hoping its just an accumulation of dust and dirt. I have never ran across this.

    • 4 replies
    • 3k views
  6. Started by Mumtedtoe,

    Hi guys just need some advice i have a cedar slab bar top and ages ago i used polyurethane on it and it started bleeding/blotching from the knots. iv sanded it back and have seen I should use a seal coat then polyurethane. my problem is i live in New Zealand and cannot get shellac sealcoat de waxed I can only get the clear coat that says I can't use polyurethane over top of it. so any ideas? Should I just do it anyway?or I could oil instead of poly... but I really want the durability that the poly will give me. so yeah I'm new to all this so help will be much appreciated ( also dumb it down ) cheers

      • Like
    • 5 replies
    • 2.7k views
  7. Started by Felix Grundy,

    Hi, New to woodworking. I built a small side table and have been researching how to finish it. I am sure there will be glasses and things put down on the top. despite best efforts I also know that coasters will likely not be used. I have heard that Arm R Seal is a good product. I have searched the forums for my specific question and despite healthy discussion have not been able to find the answer. The table is small with lots of parts. 9 rails to be exact and a floating top. I like to complicate things.... So I am worried that if I also try to put Arm R Seal on the base it will run and come out looking streaky. Should I use a different finishing method for the …

  8. I went to a local stain/varnish store that supplies many of the 80+ cabinet shops in this area to get what I need to finish the vanity I am building. Since I am new to finishing, I was asking him some questions about what he has and how to use it. One product he has is something (can't remember what he called it) that you use to release moisture that gets trapped below a layer of varnish. It redissolves dried varnish, allows the moisture to escape, and then the varnish redries. Many of the shops use it in the summer when high humidity causes problems. Has anyone here heard of or used this?

      • Like
    • 8 replies
    • 7.2k views
  9. Started by Marcus Hand,

    I'm nearing the end of a large bookcase/cabinet (12'x9') build that will be painted. My wife wants it to match the color paint that is used in our house for trim, which is an antique white color of Sherwin William's Duration Acrylic Latex. I tried to talk her into a color or color mix of GF Milk Paint. I sprayed my daughter's dresser with an Earlex 5500 and GF Milk Paint and it came out so much better than any brush/roller painting I have done in the past. I suck at painting with a brush and after the awesome experience with GF Milk Paint, I vowed to never use a brush again. I spent a little time trying to mix GF paint color to match, but couldn't get it quite …

    • 1 reply
    • 3k views
  10. Started by Chris2159,

    I recently built a full set of kitchen cabinets for a client and they want the antique glazed look over an off-white paint. I haven't had any personal expierence with this, being somewhat new to the trade. Am I better off spraying a primer/pre-cat white lacquer/glaze/clear coat? Or would I have more luck spraying a waterbourne enamel? Thanks for any input!

    • 2 replies
    • 2.7k views
  11. Started by HLDYRBRTH,

    I am in the process of completing a walnut midcentury nightstand piece. The image provided shows the solid walnut legs, solid walnut drawer face to be attached, and one side off the walnut plywood case body with a 3/4” x 1/8” walnut edge applied. None of these pieces are final sanded yet, no finish has been applied. The legs and edge banding are the same walnut color tone. The walnut plywood is another walnut color tone, a little lighter/grayer than the legs or banding. The drawer face, which I cut to show the grain pattern has a little bit of red in the walnut color. Question is….. How to insure that the finished piece does not look like thr…

  12. Started by Erik Finn Larson,

    Does anyone have experience finishing canary wood? On a recent trip to Ecuador my 7 year old son found this small oil painting that for whatever reason resonated with him. After we left the artist's studio I doubled back and bought it for him as a birthday present. I wanted him to have a frame for it made of a wood that grows in Ecuador, so I researched a bit and landed on Canary Wood. I've now made the basic frame, but need to finish it. It has such a beautiful grain pattern that I thought a clear coat would likely be the bast approach. I don't have a sprayer or really any finishing tools beyond a good brush, some rags, and sand paper. My plan of attack was: A…

      • Like
    • 10 replies
    • 8.7k views
  13. Hello, hope some lovely person can help me; I have a solid teak 1960's sideboard made by Beithcraft and while I have experience restoring I really don't want to make a mess of this one.. It has been varnished at some point in its life and the top work surface is showing some wear with a few patches where the varnish is worn away completely; the rest of the cabinet is perfect however and has a great color to it so I don't want to touch this. Any tips on refinishing the top surface only and having the color match the rest of the cabinet as closely as possible? There are no scratches in the surface so should I use a delicate varnish remover then a light sand o…

      • Like
    • 2 replies
    • 2.6k views
  14. Started by rodger.,

    I have been using an Earlex for many years, and I spray only water bourne finishes. I think I need to lubricate the gun (needle, and a few other moving parts). After doing a bit of reading, I think mineral oil will do the job well. Anyone have any thoughts on this?

      • Like
    • 2 replies
    • 2.8k views
  15. Started by dausone,

    Hello everyone! I am a first time poster, long time lurker here and have an interesting problem that I thought I would put out there and see if there are some creative solutions. First off, I understand completely the problems with using refined or raw linseed oil vs. boiled. I do not have access to boiled linseed oil as I am overseas and I also do not have access to japan driers or cobalt driers. I am using an alkyd urethane resin which has some driers in it, and it certainly helps speed up the drying process, but not by much. What do you guys think? Any creative solutions here? P.S. I am using a 1/3 thinner, 1/3 linseed oil, 1/3 urethane blend. Thanks in advan…

      • Like
    • 35 replies
    • 18k views
  16. Started by Southwood,

    I am going to try Target Coating EM6000 WB. Does anyone have any experience using this combo? Any help as far as needle size and what not?

    • 2 replies
    • 2.8k views
  17. Started by Curtis,

    What steps/materials do you guys recommend for finishing exterior carriage doors. I used CVG Doug Fir and so am going to go clear,,,(i think, or is really much better to paint for protection?). Now about the location. I am in Rhode Island. There is not much overhang so when it rains, they are exposed to elements. They do not get sun, maybe a couple weeks they will get an hour a day in the summer. The driveway gets a little mossy through the year to give you an idea of dampness. There are two sets of doors, each individual door is 46x84. And would you spray or brush? I have a Fuji MM3 so could spray. Do you lay them flat or stand all four up with a support beam/s…

    • 2 replies
    • 2.6k views
  18. Started by Marmotjr,

    For my Segmented Bowl I'm thinking of doing a French Polish in shellac. I've done shellac before, but never a polish. I know they are a lot of work, but given the piece will be turning for me, I figure that will remove a lot of the work out of it. I want to have this piece look like glass when I'm done. I usually use a CA finish for this, but I don't have nearly enough CA on hand. Normally I've read that you should wrap some cheese cloth in linen. I don't have any cheese cloth, and I'm not in the mood to drive around trying to find any in the rural purgatory I live in. So I'm thinking I'll cut out a round sponge, and wrap that in a couple layers of linen. I'l…

  19. Hello All! I epitomize the word "novice" and as such, I desperately need help with my project (my very first go at refinishing). I wanted to refinish a 20 year old maple coffee table for my wife. After doing a lot of reading and enlisting the help of a buddy of mine who used to make cabinets professionally, I began my journey. This was my second attempt at this table (we can summarize attempt one by saying that testing first is not a step one should skip) So for attempt 2, I went to a woodworking specialty store and after showing them some photos of my disaster, they recommended 3 General Finishes products: Seal-a-Cell (an oil based pre coat) to use as a pre stain …

      • Like
    • 11 replies
    • 4.9k views
  20. Started by carl,

    I am using old painted but chipped double hung wood windows for an outdoor project. I don't want to strip them just leave them as they are, maybe remove some of the cracking paint. What can I use to seal and protect them from the weather

      • Like
    • 2 replies
    • 2.5k views
  21. Started by Marmotjr,

    What stains penetrate the best? Or will most stains suit my purpose? I'm making some segmented bowls, and between each segment, I'm putting a 1/8" veneer/inlay. Now the wood I'm using for this, (I'm not sure what it is, I'm reclaiming it from some 70 year old shelves my great uncle made, I'm thinking pine), is fairly lite in color. It will contrast nicely with the walnut accent rings and base, but the bulk of the rings are made of select BORG pine boards (Ok, yell at me, go ahead :), but I like the golden yellow hue and radiant grain flecks these boards have when turned, and they're basically 1" cubes glued together, so I'm not too worried about movement, And pine …

      • Like
    • 6 replies
    • 2.9k views
  22. Hello colleagues, I just finish building a rocking chair out of ash and I would like the pale white tone of the wood to last. I feel like using oil bases finish like linseed or polyurethane would make it yellow. To conserv the white tone, I was thinking about using Briwax Limewax and then wax it with some kind of wax polish. Anybody has ever use this product or something similar? Thanks!

  23. Started by Alan G,

    I have a couple of dressers that I am in the process of building that want to have a "painted" finish. Was thinking of stepping out of my comfort zone to try a new line of products. Was looking at KemAqua Plus from Sherwin Williams. They have a surfacer (primer), kemaqua plus white (tinted) for color and then the clear for a top coat. Has anyone used these before? Thoughts? My other option was BM Advance. Long cure time though.

    • 2 replies
    • 2.6k views
  24. I finalized my planter design and have my cut list ready. I will be building this next week. I will line the interior with either pond liner or thick mil plastic. I'm using con heart redwood 2x4 for the build, the surface will be sanded all the way through to 180 grits and stained, thinking Preserva Wood pacific redwood stain/sealer but I want to add an extra layer of protection to keep the finish looking good for as long as possible. Would also like to have a semi gloss sheen to the finish. I did a gloss polyurethane finish on some benches that would show water spots whenever its wet. Should I do a semi gloss polyurethane over the finish like Minwax Semi glos…

      • Like
    • 15 replies
    • 12.1k views
  25. Started by Paul Schechter,

    I'm remodeling my 120 year old home and I'm trying to save/re-use as much of the historic materials as possible. Demoing an exterior wall gave me a decent amount of shiplap. I wanted to use it as the siding of a mechanical chase, but unfortunately the results have not turned out quite as nice as expected. I purchased a planer and took off a minimum amount of the surface on one side of the shiplap and then installed. I then Shellaced the new shiplap siding and the result was slightly more multi-colored then I wanted--see pictures. I love the oxidized wood look, but also wanted to take off the rough exterior of the wood. Planning the not perfectly flat shiplap resulte…

      • Like
    • 6 replies
    • 8.5k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.