Finishing
2,922 topics in this forum
-
My wife asked me to refinsh an old Danish modern table. She wanted a light color, almost white. I did a couple of coats of a water based stain killer primer and then 3 coats of an off white warter based enamel. It looked great, but was too easily stained by food and newspaper ink. I sanded it, did a another coat of primer, and then two coats of water based satin polyurathane. It looked even better and was easy to clean. But now I sam seeing grey spots. They look like they are under the poly and no amount of cleaning affects them. What is going on and how can I fix the table? Ed
-
- 0 replies
- 2.7k views
-
-
Question on finishing live edge maple. Table has large void filled with West Systems 105 epoxy resin. I want to use tung oil and oil base polyurethane mixed with mineral spirits for the finish. Can I apply this over the West Sysytems epoxy ?
-
-
- 7 replies
- 6.1k views
-
-
I am building a platform bed using a torsion box top. I am hoping to finish this before Thanksgiving so thanks in advance for quick replies. First I want to say I am a beginner and this is the first "fine" piece I have done, so be gentle. All the wood is furniture grade. The torsion box was built out of birch ply with a tempered hardboard top and Birch hardwood outsides. The foundation is Birch ply. I am mostly concerned with the hardwood at this point (as I don't want to sand the ply any more at the risk of getting below the top grain layer). I sanded the hardwood to #110, then #220 with a electric palm sander. I then stained the hardwood (2 coats) with …
-
-
- 10 replies
- 76.8k views
-
-
Building a desk and really wanted it a gray color. But have tested a few stains on red oak. Only have the box stores close. So red oak is what I tried.Can get anything else at a true lumber store. But that means driving over an hour. Not easy if I need a little more. And not sure maple or something else will be better. But I am willing if need be.Looking for a even uniform appearance like you would see on factory furniture or pre finished gray flooring. floor.Medium to dark gray.When I try on oak the red seems to be visible giving it a blotchy look.So far tried Miniwax classic gray and varathane carbon gray.More important to have a uniform factory looking finish. Should I…
-
- 1 reply
- 2.8k views
-
-
I have found some related topics posted before in here but can't find the answer to my specific question. I have some clam wood (fir: https://trinityrivermarine.com/information/) which has all these beautiful holes and I am using it to make a table top for a kitchen island. I wanted to show off the holes using clear epoxy resin which I have already done with West Systems 105/206. The epoxy has cured beautifully and is perfectly clear...until I sand it. Now I have sanded the surface is scratched up and no longer clear. I know from messing around that more epoxy on top bring back the clarity but I can't afford to finish the whole piece with epoxy. I am looking for…
-
- 10 replies
- 10.7k views
-
-
Hi I make CNC signs out of cedar. I paint them then use natural danish oil followed by varathane. For a recent sign I used Gold Rustoleum Universal Paint & Prime but seems that due to temperature and only allowing a few hours before oil, the oil is removing parts of it from the surface. Is it possible to paint tomorrow after the oil has set? Thanks Shawn
-
- 7 replies
- 3k views
-
-
I went to a local saw mill that had a 7" long 9" wide and 2" thick piece of mahogany. It has been kiln dried and cured in stacks for at least 10 years. I cut the board to 4 feet to use as a mantle piece above my gas fireplace. I used oak wood 4-6" wide 7" long as a background from floor to ceiling. about 9" used a light stain came out great. My question is what to do with the mahogany. I was thinking just sand it smooth than use a polyurethane matte on the board. I have read that mahogany is very porous and i should use wood filler, stain it than lacquer or poly it do i need to do all that or just sanding and poly with a matte finish. Board is beautifu…
-
-
- 10 replies
- 5.4k views
-
-
I noticed my can of polyurethane has thickened some over time, seems to have happened naturally because I always close it when I'm done. Well it isn't coming out like jello or anything like that, but it is noticeable. The fist coat seems to have yielded the same results as a new can would, but thought I'd go to the pros and see what your guy's thoughts were on it. Any warnings or word of caution jump out in your mind?
-
- 5 replies
- 3.2k views
-
-
I'm in a bit of a pickle. I'm making a couple of bathroom cabinets, and the couple I'm making them for wants a finish that ends up looking something like this: To my eyes, the wood finish closest to what is pictures is pickled oak. I've tried to achieve this kind of a finish before to limited success, so I thought I would throw a line out here and see what the think tank says is the best way to get that perfect pickle. I should add that this project does not need to be 100% identical to the finish in the picture, as I'm not matching anything. It just needs to be pickled.
-
- 3 replies
- 3k views
-
-
Hey guys, my wife and I blew our kitchen renovation budget on new appliance so we've opted to use oak butcher block for new counters. Can you guys recommend some finishes to seal and protect the oak that are food safe? I'd like a satin sheen and something a little bit darker than natural oak to bring out the grain a little bit. I've looked into waterlox but it doesn't appear that it will darken the wood any.
-
- 10 replies
- 5.9k views
-
-
I have been redoing our kitchen cabinets using General Finishes gel stain and get top coat. I really like the finish from the top coat. We have paneling in the kitchen and eating area and I can't bring myself to even consider painting it. The paneling is in good shape, but the finish has suffered over the years. I don't want to change the color as it would make the rooms too dark. I thought of cleaning it with mineral spirits or TSP substitute, giving it a very light sanding then applying the General Finishes top coat. Would that work to rejuvenate them or do I really need to restain first? TIA!
-
- 8 replies
- 3.1k views
-
-
My contractor said to put on a mix of water poly1:4 with water and then stain and then 2 coats of poly before he installs them. I put an Minwax pre stain conditioner on them (11 treads and put them in the sun to dry. It was a hot day. By the time I got back to the first one to start staining with Minwax Dark Walnut, it would not take the stain. Did I wait too long? Can I sand it off and start over? Should I use the mixture the contractor suggested instead? He says it will prolong the life of the stain. Thanks!
-
- 4 replies
- 5.4k views
-
-
I am getting ready to finish a nightstand with a curly maple top. My plan is to follow an online tutorial I found that starts by applying a coat of Blonde shellac with a small amount of transtint dye added. Followed by fairly aggressive sanding, and then the application of several topcoat layers. I have some arm-r-seal left from a previous project with a satin sheen. It struck me that a semi-gloss may enhance the curly effect better than a satin sheen. So the question becomes, does it make sense to stick with satin, or should I go with a semi-gloss? Thanks in advance for any thoughts on this.
-
-
- 6 replies
- 3.3k views
-
-
Hello all. This is my first post of many Im sure. I hope to gain a lot of knowledge from all, and hopefully I can pass on the little that I have. Im currently in the process of building my own drumset. Im still in the testing phase and working out my finish. I was looking at spraying Transtint purple cut with a 50/50 mix of water and alcohol. Im having issues getting it into the deep pores of the oak. So what im thinking is spraying on 3 or 4 coats then hand rubbing another coat of dye mixed into a watered down tintable clear stain to fill in the grain. Would this work? Any help would be greatly appreciated.
-
-
- 3 replies
- 2.9k views
-
-
I'm having problems filling the seams between strips of bubinga veneer on 30" x 60" coffee table. The veneer is laid on a 1 1/2 substrate of baltic birch ply. I sliced the veneer to between 1/8 and 3/32 and ran it through a drum sander to remove saw marks and even the thickness of each piece. I laid out the sequence of strips and ran a strip of heavy clear packing tape along each seam. I've done this many times before with no problems. Glue was rolled on bottom of the taped up panel which was then transferred to the substrate, covered with a plastic sheeting and a plywood caul and placed in the bag. The problem began a few days after the veneered piece was taken from…
-
-
- 5 replies
- 3.6k views
-
-
I've got a rubber sheet of Neoprene I purchased to protect projects from resting on a hard surface during certain operations. The sheet I got is over-sized, and I was thinking of cutting up the scraps and adhering them to the bottoms of chair legs, etc. as floor protection. Suggestions on a specific glue to use or avoid? This chart, seems to say almost anything will work, but what do those geeks at MIT really know anyways? looking for specific experience if anyone has it. https://d-lab.mit.edu/sites/default/files/D-Lab_Learn-It_Adhesives.pdf
-
-
- 4 replies
- 12.5k views
-
-
These are the floors on the main floor of my home. They were finished by the previous owner's contractor. The overall condition is good, but a couple of areas, like around the stools, have had the surface finish scraped off, when the plastic ring on one of the stools fractured and exposed a the metal edge of the stool's base. The scraping happened pretty quickly before I noticed it. I don't have the budget or inclination to refinish the entire floor, which extends into adjacent rooms, just for these areas, so wondering if anyone has suggestions on what the product or type of product might be? I think the wood is maple with a reddish cherry finish. Whatever it is, it…
-
- 0 replies
- 3.3k views
-
-
I don't know how I missed this! I'm staining and finishing a coffe table. The top turned out the wrong color. So I sanded it down and re-stained it. It had 3 layers poly coat. On doing the final inspection before the final poly I saw this. It's even grinning at me, taunting me! It must have been a drip or a cloth swipe. It's just the stain on top of poly. I tried to use water and a white buffing pad. It helped a little but not much. I can feel it on top of the poly coat so I'm hoping it can be removed without having to ruin the poly under it. But if I have to sand it off I will. I'm using varithane stain and water based poly. Any sug…
-
-
- 9 replies
- 3.4k views
-
-
This week I am building more kids furniture with Marc's table and chairs set from Woodworkers Fighting Cancer a couple years back. For those not familiar, it's 100% plywood. I'll likely paint it white. I've had mixed results painting projects in the past with usual household latex paint. Marc used lacquer, added white pigment, and HVLP'd it. This is feasible and a more attractive option, but the only turbine I have is the single stage Rockler $100 thing. I've never even used it. What say the collective here?
-
-
- 14 replies
- 3.1k views
-
-
Okay, so this is probably similar to the Cedar Mantel thread... I just picked up a fairly massive chuck of redwood that's basically 5x12 inches by 6 feet long that's going to be used as the top of a mantel. The problem is that it's still green and obviously I don't have 5-6 years to wait for it to fully dry before installing it. The client is very aware of this and does want the "rustic" look, so I'm not overly concerned about cracks and twists, but I would like to at least put some kind of at least basic finish on it to protect it and not have it look like a work in progress. So the question is, how would you prep the wood? My guess it to seal the ends a bit with s…
-
- 4 replies
- 6.7k views
-
-
I'm new here and to turbine spraying. I just purchased a Fuji 3 stage and only have one gun so, am wanting a second gun. My question is, can I use any HVLP gun with the proper fitting or, are they specifically built for turbines? Really don't want to spend $200 just for a primer gun. Thanks for any help.
-
-
- 11 replies
- 3k views
-
-
Hi All I am bit new to the forum but was hoping to get some insight for experienced wood workers regarding our sanded and stained red oak floors. We hired a contractor to strip and stain our red oak floors using a miniwax dark walnut finish and three coats of water based satin polyurethane. The entire house came pretty good except in our main hallway there is some really dark stain against the wall. We noticed as they did the work they left a small walkway down the hallway to walk into the other room. It appears as though when they stained the area to the left along the wall the stain came out way to dark and uneven. They have already applied the polyurethane and won…
-
-
- 15 replies
- 3.5k views
-
-
Using Tung oil. Minwax Tung oil to be persice on Morado. I read that going above 220 on regular wood is wasted effort. Does going higher on irregular grain patterned wood like burl help or hinder? I ask because this set of Morado grips on the left has a couple lines that streak up at the irregular spots. Couldn't see it until a few coats of oil hit it. Is it just not taking the oil as well or too well? Should I be sanding with a finer grit between coats or wet sanding? I usually just buff it with a cloth and that does the trick but it's not on this wood. I have sand paper from 80-3000 grit... i initally sanded this batch to 1000 grit. The red oak to …
-
-
- 19 replies
- 7.6k views
-
-
This is a face frame i made using the Festool Domino. I guess I didnt have enough glue in the joint so there is some separation happening. The frame is going to be painted, so I need some ideas on how to fill and bond this location. I tried spackling and drywall mud, but they both just split again.
-
-
- 32 replies
- 7.7k views
-
-
In a bit of a pickle due to my inexperience. I put on my first coat of Minwax fast drying polyurathane today, and I had some dust and dog hair fall on to my project. I figured during the sanding phase all would be well. I used a orbital sander with 220grit, and now I have these white sanding marks from the sander. Is this going to be an issue? I've read in some places to add another layer of poly, but then others saying to remove the layer. I've tried wiping with mineral spirits but that doesn't seem to make it any better.
-
-
- 8 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·