Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing

  1. Started by d3mo,

    So first off, hello! I just purchased my first house, and I'm finally able to do get into woodworking. My first wood project is remodeling the formerly carpeted stairs, and transforming them into dark walnut treads and white risers. I purchased some treads in walnut, and cut them all to fit the wildly shaped rounding staircase I have. The problem comes from weeks of frustration in getting a nice even application and consistent look between each step, along with the right color and darkness. Now I know this will make me the least favorite newbie ever, but I'm applying a dye to even all the color and tone out, and a stain to darken it. I'm sorry, and hopefully someone…

    • 4 replies
    • 4.4k views
  2. Started by emccrory,

    I have used the Minwax oil-based stains for all of my life. They look so much better (IMHO) than the water-based stains. My wife hates the smell, but I have been ok with it ... until now. I used one this weekend and did the work outside. I thought that would be fine, but I felt rather sick to my stomach afterwards. (It went away after an hour.) So, I'd like your recommendations for dust/gas masks that will block those VOC's when I use these stains again. My short search on Amazon and Woodcraft yielded this as a possible choice: "3M 62023HA1-C Professional Multi-Purpose Respirator" for about $30

      • Like
    • 2 replies
    • 2.7k views
  3. Started by Ronn W,

    I am replacing some wood slats on an outdoor chair. The owner has decided to leave the wood bare since that is the most maitenance free alternative. But here is my question.... What it I were to do just one coat of shellac just to pop the grain then apply no further finish. I am assuming that it will look a little more attractive to start with but would still weather to gray. Any thoughts?

  4. Started by Denette,

    My brother bought an 8' long pine slab and is getting me to finish it up for him as a countertop for his kitchen. It was rough-cut when I got it. So far I've milled it so that it is square and gotten a few dovetail keys in a substantial crack. It was my first effort at inlay of any kind. Check it out: So anyway, my question (and the reason this post is in the finishing section) is what kind of finish would be best for a pine slab countertop? I've been advised by a local guy that cutting oil-based poly 50/50 with mineral spirits will let it soak into the grain and harden the wood to protect against damage, but if anyone has any better ideas I'd be op…

      • Like
    • 19 replies
    • 17.1k views
  5. Started by Velvet57,

    Hello All! I finally removed paint from a table that I painted, and I'm not sure how to protect it. I don't want a shiny finish, I just want to protect it. What product can I use for a matte finish for protection? Thanks in advance!

      • Like
    • 4 replies
    • 2.9k views
  6. Started by Dan Bryer,

    Good morning. A few years back, I took my 1st drum kit and replaced the black factory wrap with cherry veneer. I recently bought a new floor tom with a *close* match, but not perfect. I have some extra sheets of walnut veneer that I was thinking of using to redo the whole kit. I love walnut, but I'd like to do something other than a natural finish. Do any of you have any suggestions for a stain colour that might actually show on the darker wood. Maybe a dark blue or purple? Thanks in advance. Dan.

      • Like
    • 19 replies
    • 5.7k views
  7. Hello all and thanks in advance for review and advice. Last time I used this board I was restoring an old Hooker floating desk, my first project. It came out very nice thanks to the solid advice found here. Now I'm onto cleaning up a Young Manufacturing Bedroom set. It's pretty cool if you like the Mid Century Modern lines. I need to clean the tops up on three dressers and night stand. I haven't been able to date it yet, but suspect 60's? If I come across a date code I'll post. The tops appears similar to my Hooker, a walnut veneer. This time I'm asking before I get the sander out! Attached are pictures of the night stand (starting small) and some close ups of …

      • Haha
      • Like
    • 5 replies
    • 3.2k views
  8. Started by AndieB,

    I have an oak dining table that is very pale, with a lacquered finish. I want to achieve a warmer oak colour and would be grateful for advice regarding the best product. I don't really want to have to take the lacquer off first and wonder whether I can use a wood dye over the top? Or is there a coloured lacquer that can be applied over existing lacquer? Advice very gratefully received.

  9. Started by collinb,

    Looks pretty nice. No staining needed. Before & After photos.

      • Like
    • 11 replies
    • 6.6k views
  10. Started by Larry Moore,

    I'm posting this question here incase anyone else can make use of the answer. Steve you have made mention on how you finish painted projects, I would like to know what filler you use after the first coat of paint. I've got a request for a special cabinet that is painted.

      • Haha
      • Like
    • 6 replies
    • 3k views
  11. Started by Rob Hamilton,

    Hey all, hoping I can get some advice from some more seasoned members here. I'm finishing two 4' x 10' Ambrosia maple table tops for my wife's art studio. On each surface, there are hundreds of tiny worm holes that need to be filled prior to finishing (see pic). My first thought was to fill them with epoxy using a syringe... but there are sooo many holes. Is this still the best route to go or is there an easier solution (wood filler, etc)? The tables will be finished with Arm-R-Seal. Thanks in advance! Rob

      • Haha
      • Like
    • 15 replies
    • 25.9k views
  12. Started by Reborn Refinisher,

    I need advice from people way brighter than I am! I found the perfect expanding table online to go with the 13’ window seat in my kitchen. Unfortunately, to make it more saleable someone ( the dealer?) shellacked the top and the three leaves. Horrors! I can’t think of a worse surface for a kitchen table. It’s obnoxiously shiny. It scratchs if you look at it. And, heat and water leave marks. So far, I been quick and avoided major damage but it’s ridiculous, not to mention the legs and stretchers don’t match the top. So, what am I to do? I planned to have it taken outside and to sand it once summer arrived. Well, it’s arrived but beyond sanding it, I’m stu…

  13. Started by Velvet57,

    I promised to post pics of table results to "To stain or not to stain". Here are the results". What do you guys think I did? Here's a reminder of the before. It had bad water stains.

      • Like
    • 10 replies
    • 3.2k views
  14. Started by Dnorris1369,

    Hey guys I’m looking at getting into spraying. I just built a kitchen table and it’s making me say it’s time to start spraying. I have a large air compressor so I’m leaning towards a gun setup for that. Can I get some advice for this or separate setup.? Pros/cons/etc. also recommendations on both. Thanks in advance

  15. Started by milwen,

    I'm trying to find out if there is any difference between mineral oil (sold as a laxative) and butcher block oil. The reason I ask is because a pint of mineral oil as a laxative can be purchased for $2.63 from Amazon and a pint of General Finishes butcher block oil is $8.99 from Woodcraft. As far as I can tell both are just plain mineral oil. According to the General Finishes MSDS the butcher block oil also contains a small amount of vitamin E, but I have also seen this listed on some laxatives. Has anybody had any experience with this? http://www.amazon.com/Cumberland-Swan-Mineral-Oil-Pt/dp/B000QFUQFS/ref=sr_1_1?ie=UTF8&s=hpc&qid=1307996820&sr=1-1 ht…

      • Thanks
      • Like
    • 21 replies
    • 69.7k views
  16. Started by Dreamcatcher,

    I am buildind a desk using barnwood (oak) and a real turquoise inlay. I have never used an inlay before. What finishing products are best used to a) not damage the inlay, and b) give you the best high use furniture finish? I would normally use a wipe on polyurethane and finishing wax. What, if anything do I need to change?

    • 0 replies
    • 2.9k views
  17. Started by John Veevers,

    Got 2 new 700mm x 300mm MDF Vinyl covered doors made to replace ones where Vinyl had split. Old doors had black plastic dowels for screwing the hinge screws into. (photo) What are these called and any ideas where they can be purchased (Perth) Thanks

      • Like
    • 4 replies
    • 3k views
  18. Started by wtnhighlander,

    I know, trendy isn't really the thing around here, but I have been volunteered to help out a work training program for disabled / special needs young adults. They need me to do the power tool work for making "decorative" cutting / serving boards and trays. The students do the sanding, finishing and packaging, then sell them to raise funds for the program. They want at least part of the batch to be "antique, weathered" style. In other words, sloppily built and grey as driftwood. Any of you know a technique or product for producing the grey color, that is: 1. cheap 2. fast / easy 3. safe for these folks to handle. These individuals are NOT seve…

      • Thanks
      • Like
    • 10 replies
    • 3.3k views
  19. Started by kipnflip,

    Hi everyone. Some background: I seem to be terrible at finishing. My projects generally turn out well, with unusual designs (motivated by having odd, mixed pieces of wood that I've collected here and there for years), solid construction and the like. My finishing skills, unfortunately, leave much to be desired. I've tried numerous products, but generally prefer stain (danish oil is easy and looks good), followed by polyurethane for protection. Several coats of a thin, wipe-on poly have generally been the only way I'll get perhaps a "fair" finish. Not good, by a long shot, but fair. Anything else, and I'd classify the finish as poor, every single time. I've watch…

      • Like
    • 8 replies
    • 9.1k views
  20. Started by Velvet57,

    Hello, all. Newbie here. I just wanted an opinion on whether to stain, this table..or leave it as is. It has 2 coats of seal coat on it.

      • Like
    • 9 replies
    • 3.3k views
  21. Started by mpc2117,

    Okay so I recently bought a house in means of remodeling it to be our starter home. The house had carpet in all rooms when we purchased it but when we tore it up we deiscovered we had hardwood floors underneath. They were a golden color before having them sanded down by professionals and re-stained using Minwax Dark Walnut. The floors turned out great except.... there are some spots that’s are lighter. We first noticed it in front of the fireplace. Then we walked into each bedroom and noticed it again. The patch is on each bedroom wall that is perpendicular to the runs of the wood. It’s about 14”-18” off each wall. They have put down two coats of polyurethane down and you…

      • Like
    • 13 replies
    • 4.1k views
  22. Started by Paul Clement,

    Hello. I'm new here. :) I wonder if someone has some advice on finishing paela? I'm making some small boxes from paela. I dressed it in my thickness planer and have scraped it and done a tiny bit of sanding. On Thursday last week I put a coat of minwax wipe on poly on just the bare wood, no stain or anything. It was a bit sticky the next day so I left it over the weekend while I was away. Late Monday it's still a bit sticky. Previously I had made a box from the same board only I finished it with Waterlox and had no issues like this. Should I not be using poly on this wood? Any other thoughts? Thanks Paul

  23. Started by Robbie H,

    Hey everyone, brand new to this forum, excited to hear responses. I am making MDF “farmhouse” or craftsman style trim for all baseboards, door casings, shiplap, etc. for my house...it’s a lot. All of that to ask, I am wondering about anyone’s experience in knocking off edges for this much material. I don’t want a significant round over since we are going with a more shaker style, but for painting, it might be best to take a small amount. Sandpaper seems like too much work for this much material, as does using a plane. I have a great router table, but I’m wondering if I even need to do this (knock off the edges) or will the paint hold better than I expect? Any experience o…

      • Thanks
      • Haha
      • Like
    • 18 replies
    • 12.5k views
  24. I need some help! I began the steps to refinish my kitchen table. Everything seemed to start out great. I used Klean Stripper and removed the finish then lightly sanded my table and then wiped with a tack cloth. The next day I applied a wood conditioner and let dry. It looked as if I didn’t saturate the wood like the directions said so I applied again and let dry. The following day I proceeded to stain with an oil base stain. Waited 2 hours and applied a second coat of stain. I was noticing the stain was not really taking to the wood so I let the 3rd coat sit for a while before wiping but still did not take to the wood. Come to read up I think the problem was that…

    • 4 replies
    • 2.9k views
  25. Started by curlyoak,

    I ran this in the section called finishing without a response. Please tell me your favorite varnish. Brush grade and oil compatible. Thanks

      • Thanks
    • 6 replies
    • 3k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.