Finishing
2,922 topics in this forum
-
Bit the bullet and ordered a gallon of General Finishes wb poly. Sprayed a good amount of lacquer in the past, with always good results. Suggestions on how I can keep that streak alive with poly would be greatly appreciated! Steve
-
- 5 replies
- 3.1k views
-
-
I hate to think of it and hate to ask. But I've been asked to build a piece to match an existing piece. The older piece naturally has darkened. I'm thinking the stained piece eventually be darker than the older piece. Anybody with experience with this kind of challenge? What stain did you use? Thanks
-
-
- 14 replies
- 4.3k views
- 1 follower
-
-
I have a customer who wants me to do a large outdoor sign with live edge pine. The customer wants low maintenance on it. Normally I use Hellsman Spar Urethane for outdoor signs. Is there an epoxy I could use that doesnt need to be maintained every year.
-
-
- 17 replies
- 7.5k views
- 1 follower
-
-
as far as sealer goes, should I treat the wood vanity base the same as the wood top?
-
- 1 reply
- 2.7k views
-
-
Hi, I finished an outdoor product with Epifanes and within a year of two, it started to flake and I had to strip and sand the old finish. A friend of mine(chemical engineer) who is in the coating business recommended the Ilva product line has being the best for outdoor clear finishes. I have already bought more Epifanes, and the comment on Epifanes, it is 20+ years old technology vs the latest (one year vs 5+ years outside). Ilva is a competitor to them.
-
-
- 1 reply
- 3k views
-
-
I don't use poly often but when I do I want a high quality bush. I know that ox hair/china bristle are best but what brands do you guys use? Recommendations and source????
-
-
- 17 replies
- 4.8k views
- 1 follower
-
-
Hi, I cut down a big Monterrey pine last year, and I'm trying to turn one of the larger pieces into an outdoor table. I left the bottom-most section of the tree as a single piece (about 6' tall) and cut it down the middle. It's about 4' diameter. So, I'm left with a flat surface that's about 6'x4'. The original cut was with a chainsaw. Then I switched to a planer. I'll finish off with a sander. What are recommendations to finish this piece so that I can leave it outside (in the sun)? I've been reading various online articles, and this is what I've gathered so far: - shellac all around the piece (for the smooth top as well as unfinished bottom). Th…
-
- 3 replies
- 3.7k views
-
-
I have a new exterior fiberglass door that was recently stained with Varathane gel stain. One coat was used. The painter did not realize that a small area was still wet prior to applying a top coat and it "pulled" the stain a bit, causing an area of buildup/darker stain. How can this be fixed? He did not want to try removing it and potentially causing more defects in the remainder of the completed areas. Any ideas would be appreciated.
-
-
- 1 reply
- 4.3k views
-
-
Has anyone else seen wipe-on poly develop a haze on the surface? I'm using Minwax gloss, on a cherry counter top. The surface was clear upon delivery to the recipient, but developed thus haze after a night in its new home. Delivery was a bit rushed, so only about 18 hours had passed after the final coat was applied, but it was dry to touch after about 4 hours. Same finish applied to other parts of the cabinet, no haze. My guess is environment changes. Finish was applied after running the window AC in my small shed, after the weather took a very humid turn. Piece was exposed to 90+ degree heat and high humidity for an hour or so during delivery, then installed in a room a…
-
-
- 28 replies
- 10k views
-
-
I have seen shellac that is purchased in the CAn diluted with denatured alcohol. Can you also use mineral spirits to dilute it?
-
-
- 16 replies
- 9.8k views
-
-
I've built a sewing/craft table for my wife. The base/frame is sprayed white, but I am still not sure how to finish the top. She has a big ironing pad and uses cutting mats, so the surface is never directly touched with hard items, but the finish needs to be resistance to damage from these mats sitting on it for long periods of time. I keep sing CAB acrylic come up for keeping maple white, but in some of the discussions it is mentioned a vinyl sealer is used first. Other discussions do not mention this. I have a Fuji Q5 to spray with, so any tips would be appreciated. If I do go with CAB acrylic, what brands are good?
-
-
- 3 replies
- 3k views
-
-
Always used minwax stains mostly but is anything that much better? For a oil stain on new work Read a lot of good reviews on GF gel stains. But dont understand why people would like the product. Seems like it dries to quick for a large table top. Does not penetrate and seems it would be more or a paint. GF does make a regular penetrating oil based stain but not in dark colors Thanks
-
-
- 27 replies
- 35.4k views
-
-
-
I started finishing my second ukulele a few days ago, currently I have three coats of Formby's Tung Oil fully dried and "polished" with very fine steel wool. I will continue to put on another few coats until it is nice, smooth and glossy, but after that I want to protect it in some way and I wondering if the tung oil will be durable enough for an instrument, and if not what do I use? on my first uke I used some minwax paste wax but that left a matte finish that looked amateur and it didn't work well with making the grain stand out so I'm worried there isn't an easy solution. The way I build ukes is very peculiar and the body is 60% exposed endgrain so I'm hoping there is …
-
- 1 reply
- 3.1k views
-
-
I’ve used wood dyes on previous federal projects but I don’t like that I must apply dye before stringing because it limits how must I can sand the wood after stringing. For my next federal style project I’m planning to use epoxy instead of wood as the stringing material. Does anybody know if wood dye can be applied AFTER the epoxy stringing without coloring the epoxy..?
-
-
- 3 replies
- 3.1k views
-
-
I had just about given up on my wood shop because no matter what I tried, I couldn't get anyone to order anything. That suddenly changed and I now have 4 kitchens to build. I am thinking about using water borne finish, but would like some more info. I read this thread - 2 or 3 times and it does have a lot of info, as well as searching several other places, and I can't find specific answers. I will start with 1 question and probably will have more. As far as time is concerned, several people say wbf is faster, but doesn't it take more steps than oil based? On a big job, drying time between coats isn't usually a factor is it?
-
-
- 25 replies
- 8k views
- 1 follower
-
-
Need some urgent help here. I just went to apply the third and final coat of gel polyurethane (Bartley) on this project and discovered a dried droplet of finish. Ughhh!!! This is probably 1 x 4 mm to give it perspective. The wood is hard maple sanded to P600, so very smooth. I don't want to refinish this whole piece. Not an option psychologically or time wise. I could focus sand this out, but will the application of an additional coat or two of polyurethane "repair" the damaged surface? Any other suggestions? Keep in mind this is a small object with a very smooth surface that will be held and examined closely.
-
-
- 9 replies
- 3.1k views
-
-
I’m finishing a chaise lounge for my deck. I’m using African Mahogany and just put a 1# cut of dewaxed shellac on it. Since it is already in sub-assemblies, do I need to hit them with a scuff of 320-400 grit, or can I spray the Epifanes spar varnish over the unsanded shellac, which feels a little rough, as all shellac does? Thanks for any guidance.
-
- 0 replies
- 3.1k views
-
-
So I've been meaning to try spraying dye with my hvlp as a means to do something with the curly maple that i have. Megan doesn't like light colored wood, or light colors in general so using maple becomes difficult as I don't care for the blotchy look from wiping on dye. Recently i had a request for some corn hole boards and figured I'd use this as a good opportunity to try out some hvlp dyeing. I figured I'd share with you all my process to either get some good feedback to get better or to help someone else along. I should start with my test pieces. I wanted to make sure that this was going to work the way I had in mind. So I took a pint of water and took approximate…
-
-
- 9 replies
- 3.3k views
- 1 follower
-
-
Wished I found this forum earlier.. Just got a 1 1/2 inch Pine Countertop installed with a sink.. yes I know. Pine was not my first choice but the selected Maple piece had cracks. Anyway, the piece is beautiful but I am fully aware of the softness of it and want to at least try to protect it as long as possible. Do not want to use Poly oil based because of the yellowing of the wood but found this product, AFM SafeCoat, Polyureseal BP which is water based urethane.. lower VOCs, etc... But the wood is soo dry and would love to give it some oil plus stain it lighly so came across one of the Wood whisperer's videos about how to this..The first step would be to oil it wit…
-
-
- 2 replies
- 2.7k views
-
-
This is my first time refinishing a piece of furniture. I am refinishing a kitchen table, I believe it is maple. I didn't notice until after a second coat of stain that one section looked scratched up. I lightly sanded with 220 grit and added 1 more coat of stain to just that section. That one section now looks dull where the rest of the table looks shiny. Any ideas? Do I sand the rest of the table and add stain like that other section? Just add my top cost and hope the glossiness all matches? Help! I'm using Minwax oil based stain. Thanks!
-
-
- 26 replies
- 12.1k views
-
-
Hi everyone, I've received a lot of great input since posting a couple times last week, so here's my next question for all of you experienced folks.. I'm making built-in bookcases (lower cabinet, upper shelves) on either side of our antique fireplace surround which is old mahogany. As an alternative, I'm getting sapele. I'd appreciate your recommendations for finishing. This isn't a table top or desk, so it won't need a huge amount of protection. The mahogany is a fairly solid color, so I'd also prefer not to really bring out the stripey grain that sapele can have. I've seen a lot of comments about using Danish oil, dewaxed shellac, Arm-r-seal, and aqua…
-
-
- 10 replies
- 4.5k views
-
-
Okay guys I need your help. We purchased some outdoor benches made out of Angelim Amargoso (an exotic hardwood) about 8 months ago. The benches were only finished with a linseed oil and have weathered horribly. The manufacture recommends a light sanding and applying more linseed oil every few months to maintain them. They are now checking and cracking along with becoming rough and changing color. Some of this is normal but even the manufacturer says that some of the checking is abnormal and they are willing to only replace those boards. I am not a fan of refinishing these with linseed oil every few months and want to apply a much more robust outdoor finish. I would…
-
-
- 4 replies
- 2.9k views
-
-
I build a top for my audio cabinet out of red oak and MDF. The joints are glued with Titebond II. I put several layers of Tru Oil into the oak and I have changed my my mind and want to get rid of the oil. I’d like to use Citristrip to pull out the Tru Oil. My concern is that the Citristrip will also dissolve the glue. I’ve read that Citristrip doesn’t dissolve certain “cured glues.” Does anyone know how Citristrip interacts with Titebond? If Citristrip isn’t the answer, then what is?
-
-
- 8 replies
- 4.7k views
-
-
Hello folks, My wife and I stained our oak floors with a dark stain (minwax 'provincial'). When it dried it revealed many variations, random light spots and some marks we hadn't seen when the floor was bare. Would anyone have any advice for us on how to correct this and make it look more uniform? any opinions and ideas would be appreciated as we are new DIY folks. This is our first floor and Deb is very worried. Thanks much, John & Debbie (pic attached)
-
-
- 25 replies
- 59.1k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·