Finishing
2,922 topics in this forum
-
I learning on your site a mix of 1/3 eurothane, 1/3 tung oil and 1/3 napha can produce a good finsh coat. What drying time shoud I allow and is buffinf needed. The surface after 24 hours feels oily still.
-
-
- 3 replies
- 3.1k views
-
-
I've applied two coats of Helmsman spar urethane over the original polyurethane finish that has been on the white pine interior of my sauna for years. After a month of heating the room and running a box fan, my son's asthma flares as soon as he goes inside. Checked with Minwax and they said it would never cure and be safe for anyone in this setting and that I should remove it and find something different which will be a huge task (it's on walls, ceiling & benches). Is there something safe that I could apply over it that would encapsulate it? If not, how best can I remove it and what would be a proper finish that can handle the water and temps to 200 degrees. Wou…
-
- 4 replies
- 3.3k views
-
-
For oil base what is the best way to clean brushes. And also proper disposal of the waste. Thanks
-
-
- 10 replies
- 3.8k views
-
-
I am fixing stair treads from where a stair chair was bolted to. I have done the repair and have sanded the plugs smooth. I am trying to stain and blend to match existing but the areas I sanded will not accept the stain. I have read some articles stating that I may have sanded to smooth because of sanding the existing finish. I also read to use mineral spirits also. the area sanded does feel like glass. I am assuming that is because of sanding the finish which acted like a polish. any ideas what to do so it will accept stain. Thanks
-
- 2 replies
- 2.9k views
-
-
I am in the process of building a Bubinga and Wenge entry table for some friends. I would like to fill the pores on the top and base. I am looking at using Aqua Coat Grain Filler. My topcoat will be GF High Performance sprayed with an HVLP. I like the way that oil brings out the chatoyance on Bubinga and may give some depth to the Wenge. My question relates to using the grain filler over an oil. Has anyone used a product similar to Aqua Coat over something like a Seal-a-Cell or ARS base coat? Would there be any issues with adhesion assuming the oil coat has 3-4 days of cure time? Any information or suggestions are appreciated.
-
- 1 reply
- 2.9k views
-
-
Does anyone have any suggestions? I buy those Ikea LED lights with the spring clamp base, then glue rare earth magnets to the bottom. These work very well for me at the lathe and bandsaw, etc. The problem is the the adhesive keeps failing. I have tried CA and DAP Rapid Fuse as well as hardware store squirt tube epoxy. Rapid Fuse did the best, but all have failed, and it appears the failure is at the glue metal interface. Any suggestions on another adhesive to try? The metal casing of the magnets is smooth and shiny. I need something that wiil stick to that.
-
-
- 24 replies
- 8k views
-
-
-
I just completed a cherry gun cabinet. I applied shellac for the finish. The wood has the typical “salmon” color which is typical with the cherry that I’ve worked with in the past. I know that the wood darkens as it ages and like the darker (wine-like) color. My question is; does applying furniture wax slow this darkening process because of its effect on sunlight...?
-
-
- 2 replies
- 2.9k views
-
-
I'm not quite sure what the original wood was. It almost looks like it was a combination of woods. I sanded my dining table down to almost a white finish. I applied a slip coat of mineral spirits and then the Gel stain Brown Mahogany gel stain. I waited 24-48 hours and applied a second coat. This wasn't the color I hoped for (again accepting the color differently according to the wood) so I waited again and applied a third coat. It looks as if each kind of wood accepted it differently again????? What can I do? I thought about going out and buying the Java gel stain and just going darker hoping that it will cover it. Would I have to lightly sand (220) the wh…
-
- 7 replies
- 4.9k views
-
-
I'm making a farmhouse table for a friend that wants it made out of pine. He can't spend the money for walnut or a hardwood so my question is can I use epoxy resin to finish this table top with expansion and contraction without cracking? The table is 42 x 72 x 3 with breadboard ends. The pine I'm using is yellow pine glued with biskets. All surfaces have been jointed and planed. Moisture content is 10-11. Any ideas? Can someone help me? Thank you in advance. This is tabletop epoxy. 1/8 inch thick
-
- 4 replies
- 2.9k views
-
-
So I have some RTA cabinets on their way to use as the base for a new bar. My wife and I agreed on cherry for the bar. My vision was to stain them about the color of our 15 year old cherry kitchen cabinets which were done with Valspar Graintone Wiping Stain - Teak. I LOVE the look of those cabinets! Nice and light and really shows off the grain of the wood. Doesn't look like that stain exists anymore though. My wife, of course, was thinking completely different. She wanted it to match the barstools she bought. They are stained something called "Hampton Cherry". Here's a sample. Yikes! I will try and talk her into something lighter, but in case…
-
- 4 replies
- 2.9k views
-
-
Hi, using dewaxed shellac with a few coats of poly-urethane has been my goto solution to finish cherry for a few years. I am finishing a piece which had 2 sides with 1/4" cherry plywood. For once, I thought of finishing the plywood prior to set it in the piece, with the 2 coats of shellac, planning to put the poly once assembled. Now, all the pieces has had 2 coats of dewaxed shellac, every is finishing normally, except the 3 pieces of plywood. The poly is cracking like 'milk-paint' does, but only on the plywood. I may have used an older can of dewaxed shellac for the plywood vs the rest of the piece, but I am not sure. I have sanded it,…
-
-
- 5 replies
- 3k views
-
-
Hi all, It has been a long while since I left the woodworking business to head back to the lovely world of Government contracting. I have recently started doing some woodworking for my own needs. I also moved from colorado where I used to buy Sherwin-Williams Acrylic Conversion Coating (CC-F52) pre cat finish. The local store would get it delivered in a 10 sheen which for my needs is perfect. Now that I am on the east coast the SW stores seem to have no knowledge of this product. After some work I was able to get a local store to source me some but they could only get me 5 gallons of the stock Dull-Rub sheen (T77F63) which is about 17-21 Sheen and way to glossy f…
-
- 0 replies
- 3k views
-
-
Hi everybody. I am new to staining wood. I needed to refinish our mantel which was cracked in many places and had a lot of holes. I suppose it's pine wood, over 30 years old. I filled the holes with "plastic wood", sanded with orbital sander to remove original finish and stain (80, 120, 220 grit), then used Rust-Oleum Kona wood finish, 2 coats. I planned to add a couple of brush-on Minwax polyurethane coats. I am not sure I like how the grain looks on the piece shown in the pictures. In some places, the wood barely took any stain at all, and the contrast is too great. My other family members love the look; however, I wonder if there is anything I can to to reduce the…
-
-
- 2 replies
- 3.3k views
-
-
Hi, Love your videos. I am very inexperienced - so be kind. I am trying to match new wood (birch and pine) to existing wood cabinets. I filled in gaps with wood filler. Then I sanded the new wood, pretreated it with a 50/50 mix of Seal Coat and Denatured. Applied the Dark Mahogany Gel Stain from General Finishes. I ended up with three problems. 1) Blotchy wood filler. Stands out like a yellow warning flag. 2) Too much grain showing through. The original cabinets have very little grain. 3) A little too purple. I thought to sand down, try to put a skin of wood filler over the whole surface and then apply another coat of Sanding Seal and t…
-
-
- 15 replies
- 5.3k views
-
-
I have a wood project on which I got birch wood that has very interesting heart wood shapes surrounded by sapwood. I originally got general finishes oil arm r seal but after trying it on a sample I feel the wood is too light in color and the heart wood doesn’t stand out as much as I like it too. I want to darken all the wood while keeping the heart wood shapes darker so the shapes pop or stand out from the rest of the wood. Any input is appreciated since I am new to wood working.
-
- 2 replies
- 2.8k views
-
-
Can the epoxy coat on live edge be sanded to fix ripples and imperfections
-
-
- 7 replies
- 3.9k views
-
-
I've been using a shellac finish. Sand to 220 > coat > 220 > coat > steel wool > coat and sometimes a 4th coat. Brushed on with disposable natural brush. Anyway to get a more matte finish. Could I steel wool it without doing another coat? Sent from my iPhone using Tapatalk
-
- 4 replies
- 6.1k views
-
-
We have someone making shaker kitchen and bathroom vanity cabinets for us. Before hiring he said he uses birch wood for his cabinetry. Once they were installed we learned the door stiles are pine and the front flat part is what he called sande ply but another woodworker believes it is luan ply wood. The boxes are a decent looking plywood but I’m very concerned about the fronts denting. Aside from being mad at myself for not getting the wood type in writing on the contract and not knowing more about wood until it was all installed, is there anything that can be done to treat the wood to make it more durable? I’m now reading how soft pine is and that it can warp. He claime…
-
-
- 16 replies
- 5.1k views
-
-
Hello, I wonder if anyone can help? We are restoring our solid wood kitchen work tops. They were sanded back, cleaned using turps and then Danish oil applied. Thinly 3 times They have been drying for 3 days, so I assumed they were fully cured but they are now covered if white marks, where water had splashed. Also cup marks etc Does anyone know what may have happened or how to rectify it? Many thanks Dena
-
-
- 74 replies
- 43k views
-
-
So I find out that California has banned the sale of Denatured Alcohol. What else can I use to mix up a batch of shellac? Before you suggest grain alcohol, we haven't had that since 1969
-
-
- 27 replies
- 9.5k views
- 1 follower
-
-
Hello, I am working on an oiled teak desk from the 1960s. There are a couple of bruised lines about 3/16" wide, running the entire width of the desk. I do not feel a dent in the wood so thought I could sand out the color difference. I first stripped the wood with Citristrip and now I've tried sanding one of the line out using 220 and 320 grit paper. It's sort of working but I'm afraid of going through the veneer. Does anyone know if Oxalic Acid wood bleach will fix this? Or is sanding the only way to go? Thanks for any advice you might have. - Tonya
-
-
- 8 replies
- 7.4k views
- 1 follower
-
-
I am restoring a 100 year old church pew. I stripped it, sanded it, and applied minwax pre-stain and minwax oil based provincial stain and over the last three days, 2 coats of spar urethane. All this BEFORE I realized the minwax products are for interior use only!!!!!!!! This morning I applied the 2nd coat of spar urethane when I noticed about 15 blisters on the end of the bench that was in the direct sun. Can someone on this forum give me some advice? Should I just stop right now and get out my heat gun to remove what I've already applied, start all over with a stain suitable for outside? I'm very upset to have put all this work in and only made MORE work for my…
-
- 7 replies
- 54.3k views
-
-
Hi. I have a very specific question and I’m hoping you folks can help me. Im familiar, as are may of you, with Osmo Polyx hard wax oil. I’m wondering if anyone has SPRAYED Oli-Natura. This is of course the sprayable version of the Osmo oil. But my question concerns cleaning my equipment. The oil dries hard. What do I use to avoid the product hardening in the spray equipment? I’ve been looking for a contact person in Germany for the details about the product. Can’t buy it in the US. Had to order it from England. Any help would be greatly appreciated. Drew
-
- 3 replies
- 3.1k views
-
-
Is there a spray alternative to Arm R Seal for large projects? Good morning. I've just completed a large hexagon breakfast table made from hickory, the top is 69" wide with a hex base that is 28" wide and 36" tall. I made the base with six panels similar to door panels and one of those is hinged that provides access to the inside which will allow my wife to store items on the base and a center shelf. Needless to say this is a lot of area to cover with a lot of contours and hard to reach areas. I have used Arm R Seal in the past based off of research I've done on this site and others and though it provided a beautiful and very tough final finish it was extremely di…
-
-
- 6 replies
- 2.8k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·