Finishing
2,922 topics in this forum
-
I am in the very high end custom cabinetry and millworking industry. We never do the same finish twice and i'm constantly coming up with new ways to finish products. Just wondering if anyone else out there might be in the same field and would like to exchange ideas or information. Also, anyone on this site is more than welcome to pick my brain with any questions. Adam Law
-
-
- 13 replies
- 3.6k views
- 1 follower
-
-
When applying the second coat of Lee Valley polymerized Tung Oil Sealer on a Cherry Table i'm working on, I noticed there were little clear dots on the surface. I couldn't rub them out so I continued with the second coat hoping that when I wiped off the excess these dots would disappear. Nope. Any advise ? I did rub the surface after each coat to get the access off. and 2nd and 3rd rub downs after each coat.
-
-
- 12 replies
- 3.8k views
-
-
I’m in the process of finishing a bow front chest. I veneered the cabinet sides and front apron with African Mahogany ( ignore the drawer fronts because they are a different species). I also used the same species for the legs (8/4).I compared the veneer with the 8/4 for color match prior to milling and I was satisfied . The legs are now much lighter in color and don’t match the veneer. I know that Mahogany darkens with age and assume that the legs will darken; however, should I try to match the legs using extra applications of the wood dye that I’m planning to use or will they even out if I leave them alone?
-
-
- 11 replies
- 3k views
- 1 follower
-
-
I just received a call from an uncle in Louisiana that reshaped a gun stock and took the finish down to bare wood. He said that the wood was heavy and light in color. He purchased Minwax ebony penetrating stain and when dried, it was only a light brown in color. He was hoping for more of a walnut color. Having never used stains before, I told him I would ask on here. Anyone have any suggestions?
-
-
- 14 replies
- 3.4k views
- 1 follower
-
-
This is my first post so hopefully it's not a dumb question! I'm new to finishing wood, but read for dozens of hours trying to learn. I purchased a walnut butcher block counter for a kitchen island. It was hand made in the USA and arrived fully sanded and oiled with a coat of mineral oil (it's the only option given). I want to eventually use Waterlox however it's winter and need to do it in the kitchen, thus with the smell and cold temperatures make it a better spring/summer project for me. I chose 100% pure tung oil (NOT tung oil varnish) mixed 50/50 with citrus solvent and started to remove the mineral oil. I sanded it down, cleaned it with solvent, sanded it aga…
-
-
- 17 replies
- 12.4k views
-
-
My well intentioned son purchased a large roll of paper backed teak veneer for me for Christmas. Although this wouldn’t have been one of my choices, I want to try to use it on some type of project. I thought that I read that teak can’t be finished with traditional wood finishes? It seems to have a oily type of finish on it? Can anyone advise me on what type of finish to use?
-
-
- 6 replies
- 3.2k views
-
-
Hi i made my wife a spoon last week. After soaking in in mineral oil for 4 hours we let it sit for 3 days. She used it to sautee some mushrooms and she washed it the next day (by hand) it started to crack on the end, what gives? Not enough oil? Wrong wood choice? Its made of cherry. How should i finish my spoons so this does doesnt happen again?
-
-
- 10 replies
- 6.4k views
-
-
I need to put a quick plaque together this weekend for Tuesday. Looking for advise one quick finish that will give a nice semi gloss to full gloss appearance and be fairly durable. Any advise? Thanks in advance
-
-
- 4 replies
- 3k views
- 1 follower
-
-
I’m planning to apply grain filler to a mahogany veneer project that I’m completing I was told that I would be wise to apply dewaxed shellac before applying the grain filler. Is this true.?
-
-
- 2 replies
- 3k views
-
-
A friend is giving us about 700 sq feet of American Black Cherry wood planking of various lengths and widths. It was pulled off the walls of a house built in 1955, so it is at least 63 years old. It’s in OK but not great shape, (tape adhesive residue, nails, some cracks) but we need flooring in our home, and this is 3/4 inch thick, tongue in groove, solid wood, so we are going to give it a shot. Black Cherry is supposed to be softish but this wood seems as hard as a rock. I can not make a mark with my fingernail. Here is a photo of 6 of the smaller planks. Like I said, the cherry wood planks were used as wall paneling in a large den & library. So they are in goo…
-
-
- 7 replies
- 3.8k views
-
-
Hello all, I finally squared all of my boards and started to test finishes. One thing I found quite quickly was that plane finishing really didn't work well. Maybe it my blade (which was damn sharp) but it took off chunks of wood and couldn't follow the grain. I also think it got stuck on the flecking. Is this common or did I do something wrong? Sandpaper will work and I did a 120 and 220 and then used compressed air to get out much of the dust. Any other tips on how to get the sawdust out? Next was the actual finish. I went with a 100% tung oil thinned 50%. It gave the oak a beautiful deep brown and the flecking was awesome. I am going to finish …
-
-
- 3 replies
- 6.5k views
-
-
So wife wanted a jewelry hanging cabinet and she bought the spray paint. She's out of town. I started to spray the primer, stopped and went out a bought a proper mask. Finished the fast dry primer and put the first finish coat on. The mask worked great but even with my 2 small exhaust fans in the basement the rest of the house had fumes. So a took the dogs to the park for a couple of hours and, coming in from outside, the odor was still pretty strong. The wife comes home tonight so I have the bathroom fans and the stove hood fan going full blast and the front door partially open. It's 20 degress outside and the furnace is working overtime. The dogs are staring at …
-
-
- 5 replies
- 3k views
- 1 follower
-
-
Hi, I need some advice please! My husband is putting a floating "desk" into a closet to create a homework space for our grandchildren. For the first part of the desk, he used a piece of red oak plywood, glued and biscuit-joined another small piece of wood (not sure what kind) across the front to give it a finished look, then sanded it all down. It looked so nice, and then I got ahold of it. On early Sunday afternoon I rubbed in one coat of Danish oil, let it sit, wiped it dry. It was outside under a carport and my husband covered it overnight with a moving quilt. I didn't realize it had to dry for a longer period of time before doing anything else to the wood and on Mond…
-
- 7 replies
- 5k views
-
-
I have been playing bass for awhile and recently I wanted to make a ukulele as a challenge... after 4 days of work I finally finished her. I was never good with poly or varnish, so I used some danish oil (3-4) coats so far and was planning on applying some paste wax. I used some redwood with very tight grain and it is sucking up the oil... I applied a ton but it keeps absorbing it and looks dry after a few hours, the maple on top looks fine but I don't know where to go from here. the inside of the uke only has one coat inside and i don't know if the wax will ruin that because the outside will be coated and the inside will be un waxed. So all I'm asking is if the wax will …
-
-
- 7 replies
- 3.6k views
-
-
I had made several chairs in cedar and never had a problem. Then I made a chair for my wife in Cypress because the wood store was low on choices for cedar. Originally I was very happy with working with it. It only took a month or so and this black/blue dots and smears started showing up. I assume it's mold but don't know. Does anyone know if : #1 is this normal for cypress? #2 will it perhaps go away on its own in the sun maybe during the summer #3 if not, what's a good approach to get this cleaned off and resealed? I originally sealed it with cedar seal - which I used on cedar. Seems to work OK and figured it would work ok on this. Original and molded pictures at…
-
-
- 8 replies
- 5.5k views
-
-
I have a dining room table, in 3 pieces, the ends are from the 1860's the center addition was made around 1940. I am told they are cherry with mahogany stain. they have an oil rubbed finish. on rare occasions it has had wax polish such as pledge or briwax but mostly just lemon oil. It had some dull dry spots and I was advised to use a mix of equal parts linseed oil, turpentine and vinegar to feed it. Now the table is sticky and attempts to rub it up make it dull and it is catching dust and lint in the sticky coating on the surface. the linseed oil mix is not very liquid and has "tracks" left from the cloth I applied it with. Those need to be gone to get back to the forme…
-
-
- 3 replies
- 3.3k views
-
-
Long time reader, first time poster. I couldn't find any answers perusing the forums. I recently made the TWW Kids Table and Chair set using Maple plywood. I decided to use Woodcraft's 100% Pure Tung Oil to finish it since I wanted to experiment with the Tung Oil a little on a piece that was going to get crushed by my (soon-to-be) 2 year old son. Anyway....I applied 3-4 (I honestly don't remember) coats of 50/50 Tung Oil and Mineral Spirits a week ago. The plywood is now slightly waxy feeling, slightly fuzzy in spots, and has an uneven sheen on the surface (as in some spots are shiny and others still dull). My question, I guess, is do I continue the 50/50 …
-
-
- 3 replies
- 3.7k views
-
-
Would there be any advantage to applying furniture wax over a shellac surface..? Would this damage the finish?
-
-
- 5 replies
- 8.3k views
-
-
Hey all! A co-worker of mine decided to try to strip their bathroom cabinets and repaint. It seems that they did a fine job I'm the boxes, but the doors are not able to be refinished as they are chipboard. He and I have chatted about woodworking as I have gotten into the craft, and the other day he asked if I could make for cabinet doors and a drawer front to replace the ones they ruined. I've got my sock, and I plan to start cutting tonight. What I'm not sure about is what the best method to prep for paint will be. I intend to do a superb job on these, with the hopes that it may lead to more business in the future, either from other coworkers or from our custo…
-
-
- 7 replies
- 3k views
-
-
So I know Wthighlander posted once about lye and using it on various woods. I was always intrugued by this and wanted to try it for myself. I recently finished adding fronts to my out feed table drawers and was going to use the drawer fronts as my test bed. I took some water and mixed in some lye. I used the 100% lye drain cleaner stuff. I applied it with a paper towel not taking much care and just slopping it on. I did take care with PPE and made sure to have glasses and rubber gloves on. I know lye is dangerous stuff so while I'm playing around I'm not playing around. I also have long sleeves and pants on to make sure to not get any chemical burns. Also V…
-
-
- 6 replies
- 6.4k views
- 1 follower
-
-
While gathering info on making complex mouldings I ran across some picture frames that were made from 2 or more pieces glued together to creat a complicate moulding and the pieces of the moudling were dyed different colors prior to assembly. That prompts this general question........ What species of woods are best for dyeing on smaller projects where grain patterns are not as important as getting the dye to take evenly? and........What species of woods are best for dyeing on larger projects where the grain is more important?
-
-
- 19 replies
- 4.1k views
- 2 followers
-
-
So let's just say that this is hypothetical...... Just say that I had one coat of poly applied to a flat surface am and doing my "betweeen coat" sanding (by hand) and, after wiping the dust away I have some shiny, low spots that I would like to get rid of. I figure that I could be a little more aggressive with the sanding to decrease the depth of the low spots so the next coat has a better chance of levelling them out. What if....in the process, I sanded throught the one coat to bare wood in a couple of spots. If I then apply a second coat of poly, will the area that was sanded through be visible???
-
-
- 16 replies
- 4k views
- 1 follower
-
-
Hi All, I absolutely love the wood whisperer. I am getting back into woodworking after a very long time. I find this site and videos to be really good and accurate, both things spectacularly missing from youtube. That said, I am finding gaps, particularly for beginners. For my first major project, I am building out bookcases. They are going to be 6ft tall by 32in wide. The sides, top, and bottom are white oak, the shelves are white oak plywood, and the back is white oak plywood. What I can't seem to find any information on is how to finish a huge piece like this. I expect that when this is glued up, it will weigh close to 100 to 200 pounds. So how would yo…
-
- 5 replies
- 3k views
- 1 follower
-
-
-
Good day, I am very very new to HVLP (Thank you Marc and Nicol i was the winner of the Fuji 3 stage can you guys tell me what finishes you like to use with the HVLP and how you use them (how much and what to dilute, what cap set and any other tips you have) greatly appreciate it.
-
-
- 7 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·