Finishing
2,922 topics in this forum
-
The attached photo is a sample of a pine finish that really makes the grain stand out. I have been blowing my brains out trying to duplicate that affect. All my tries with gel, dye to oil stains come out way too dark masking the grain. There is likely a simple method to this, but being a simple guy, I can not for the world figure it out. Thus, I beg for help from the forum mavens. (Not concerned with the blotchiness) Thank you!
-
-
- 17 replies
- 24.7k views
-
-
I have always used old white tee shirts for wipe on finishes but I was wondering if anyone had used tee shirts that were colors other then white. I have a number of Carhartt Tee's that need to be retired and I would like to give them a second life but I didn't know if the dye in the tee's would effect the finish in any way.
-
-
- 14 replies
- 3.4k views
-
-
I finished this barnwood table my husband made with an exterior water based polyurethane last year (5 coats). It overwinter with a tarp over it and came through pretty good- but I wanted to add a couple more coats of poly this spring. After my 2nd coat, it lightly drizzled a few minutes when I wasnt home and table wasnt covered. It fried and I have white thin film in crevices of the grain. I cannot stand them because they are in the crevices. What should I do??
-
- 4 replies
- 3k views
-
-
I understand using a polyurethane and putting a flat finish down first then putting a semi gloss or a gloss finish on top of that. I’m looking for an article or articles that explain the whole meaning behind this could you please direct me to some of them or all of them thank you very much
-
-
- 9 replies
- 6.8k views
-
-
Recently sprayed catalyzed varnish over rustic slab dining tops and tops are developing wrinkles over the epoxy filled grain cracks and knot holes. The rest of top is fine. Has anyone seen this?
-
- 3 replies
- 2.9k views
-
-
Is there such a thing as low viscosity epoxy adhesive? I would be interested in something watery.
-
-
- 10 replies
- 3.2k views
-
-
Just completed assembly on my project and for a finish I want to try shellac and dye. I have never used shellac (other than the spray can stuff) before, nor have I ever used dye. Do any of you have any recommendations of a good resource where I can learn shellac? Like a shellac/dye 101? I know I can just google it but that is a bit of a shotgun approach, my hope is that you guys could give me more of a focused direction.
-
-
- 26 replies
- 11.7k views
-
-
First time poster here. I recently purchased a two-tone solid sheesham dining table that i want to protect as much as possible. It came with a factory film finish but I want something that will be pretty resistant to liquids, etc. that I dont have to worry about all the time. Factory finish is very smooth but can't tell if its satin or flat (has the slightest hint of shine). I want to do this myself. Doing some research here (and sites like houzz) it seems that General Finishes High Performance Water Flat might be the best/easiest option - and following their directions for previously finished/high traffic application (clean with dna, sand with 220 sponge, cle…
-
-
- 2 replies
- 3.1k views
-
-
I am posting this question here for greater visibility. I am using Titebond Quick and Thick for my project in the journal section that involves gluing up layers of veneer. Things have been going well enough, but this morning when I took the stack out of clamps I was surprised to see that the last glue line had turned black. And another corner: Quick and Thick dries clear, so this is completely unexpected. To be honest it looks like mold, but I've never heard of a PVA type adhesive supporting microbial life (although I do remember a kid in grade school who had a habit of eating paste). My immediate suspicion is the container of water I have b…
-
-
- 16 replies
- 5.6k views
-
-
I have built a box with some nice figured wood and have applied Danish oil to bring out the curl. I want to give it a coat or two of lacquer for protection. How long do you think between the Danish oil and applying the lacquer.?
-
-
- 3 replies
- 3.5k views
-
-
Oak bathroom cabinet. Did doors and base frame using 1000 steel wool and mineral spirits then linseed oil rub. Looks great. But apparently the three small drawers had a varnish of some sort that the steel wool did not remove and the linseed oil did not penetrate and the finish looked horrible. I ended up stripping the three drawers - now they are light in color with no finish at all left on them. Should I get a medium to dark oak stain and put on them first before the linseed oil and hope that it matches the color of the rest of my cabinet? I am afraid the linseed oil only will not darken the oak enough to match the rest of the cabinet. Your thoughts?
-
-
- 3 replies
- 2.9k views
-
-
I am building a redwood firepit (LP gas) table using a repurposed redwood slab. I was thinking of jazz'ing up the table with LED lights buried under epoxy surface coat. Does anyone have experience with this? I havent done this before and would appreciate some guidance. Thank you in advance.
-
-
- 2 replies
- 2.6k views
-
-
I can't seem to find an answer to this anywhere. I'm using Arm-R-Seal satin, and dealing with a streaky finish. On General Finishes website, it says you can remove streaks by buffing with 0000 steel wool. My question is, do I wait until the 30 day cure time has passed, and then buff with steel wool? Or should I do the buffing during the cure? I applied my final coat a couple of days ago. Thanks!
-
- 6 replies
- 6.5k views
-
-
Hi, I am looking to do a giant Jenga game. The block must slide easily, whether humidity or temperature is high. In my past project, I did not have to worry about finished parts having to slide on each other. Finishing suggestion ? martin
-
-
- 7 replies
- 8.7k views
-
-
In case nobody else saw this... Charles Neil has been posting his entire class on finishing over the last several days. There's 71 videos so far. A ton of information on spraying, wiping, brushing, sealing, sanding, filling, you name it...
-
-
- 12 replies
- 4.3k views
-
-
I live in Western Kentucky and built an outdoor kitchen. I wanted to use wood for the counter tops with a burnt finish. It looks really good but my question is what is the best thing I can do to waterproof it? Poly, varnish, etc?? I want it to look good for years of course and don't want it to warp any. I used pine for the counters because I like the way it looks with a burnt finish. I was going to use several coats of Polyurethane but was told recently it may not work as I hope. Any thoughts?
-
-
- 9 replies
- 5k views
-
-
Can I use an oil and wax mixture for maintenance of pieces that I have previously finished with an oil and wax mix? Seems to me there is contradicting information on this. I'm aware of the following info: 1. We can mix wax with (boiled) linseed oil to create a 2-in-1 finish. Oil penetrates the wood, wax leaves a subtle shine and soft protective layer. 2. We can not apply oil over wax. Oil needs to penetrate the wood. In the presence of wax it will just sit on the wax and not be useful for wood. We can apply the oil, but when we wipe of the excess, you're basically wiping off everything you applied in the first place.... This sounds logical to me and seems …
-
-
- 19 replies
- 8.9k views
-
-
Does anyone here have any experience using Gilders Paste or similar products? https://www.woodturnerscatalog.com/p/50/6146/Baroque-Art-Gilders-Paste?term=gilders+paste&term=gilders paste https://www.gilderspaste.com/
-
-
- 5 replies
- 3.1k views
-
-
I’ve been using water based grain filler on my mahogany projects recently. I’ve noticed that the filler has left visible swirls when finished. I allow the filler to dry for 30-60 minutes and wipe it off. I also sand the surface lightly w/ 320# paper. I mix wood dye with the filler and I’m afraid of using more aggressive sandpaper fearing that I’ll remove some of the dye. I finished the project with 3 coats of shellac; sanding between each coat. Any advice appreciated...
-
-
- 3 replies
- 2.8k views
-
-
Hi all, I’m a major newbie but an enthusiastic one at that. I’m determined to wood veneer my cheapo mdf previously vinyl veneered bathroom cabinet. I did ok with the first step, of the actual edging the face frame and then veneering and edging door. I mean, it wasn’t pro level by any stretch, but for my first time, I was content with the result. I used psa walnut wood veneer, plain sliced. Heres a pic of the raw finished veneer job. Now, the problems started when I wanted to stain the veneer. I love the Midcentury look, so I wanted it a touch darker than the raw veneer, but a finish that would seal the wood from water spots and look smooth b…
-
-
- 6 replies
- 3.4k views
-
-
I stripped, sanded and refinished my stairs in my house which is almost 40 years old. The stair treads appear to be made of pine and were once covered in carpet prior to us purchasing the home in 2011. Obviously there are a lot of imperfections and carpet staple holes so I’m not looking for perfection. I purchased American Tecnologies “WoodFil EPOXY” wood filler for some rather large spots of which one was right on the rounded front edge of one of the treads. Everywhere else I used it, the filler and surrounding wood accepted the stain just fine so I’m not convinced the filler is the issue. This one spot on the top tread (of course) where I filled in a large inden…
-
- 1 reply
- 7.1k views
-
-
I may be able to get a new spray system soon, but my budget will determine what I can get compared to what I want. I hardly know anything about it so I might be mixing apples and oranges in my questions. I like the Mini Mite 4, but I would like to have the spray gun separate from the container with just hoses feeding the gun. Could I get a paint pot and hoses that would work as a good system with the Mini mite? Is there another good brand that would work like I want without adapting? Any info helps. Thanks.
-
-
- 4 replies
- 2.9k views
-
-
I am considering purchasing a Homeright Super Finish Max HVLP Paint Sprayer and would appreciate any information anyone would have. I am also interested in anything anyone would like to share in regard to similar HVLP options at an affordable price. I have a larger air compressor in my shop, but my (clean) finish area is in the house basement and I would prefer to avoid the hassle of moving the compressor back and forth. I also have a smaller air compressor for my finish area but use it primarily for final brad nail assembly and it is likely not large enough for spraying. I would also like to avoid the issues involved in HVLP spraying with an air compressor as the source,…
-
-
- 8 replies
- 4.3k views
-
-
Trying to get my ducks in a row for my first major project, the WW Miter saw cabinet. This will be my first piece of shop furniture. Being that it's shop furniture, what is the rule of thumb for finishing it? What product would you use? Something easily repeatable, maybe a little waterproofing just in case.
-
-
- 10 replies
- 3k views
-
-
Small preview of some of the work we do.
-
- 0 replies
- 2.6k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·