Finishing
2,922 topics in this forum
-
Hi Folks! Thanks for all the awesome advice you've helped me with in the past. I've learned a lot from you guys I'm making a raised garden box. It's made from Douglas fir. Not the best choice, I know. I'm about to assemble it and been thinking on what to do to the outside of it. I'm leaving the inside bare wood. I'm growing fruits and berries in it so I don't want chemicals in the growing bed. I was planning on painting the outside to give it some protection but wasn't sure if I did just the outside of it would make the wood warp and crack faster. The walls are made from 2x12 and the legs are 4x4. It's been sitting in my garage for about a year. I'd be usi…
-
-
- 22 replies
- 4.4k views
-
-
I need to find a reliable varnish. Brush grade. Compatible with mineral spirits. Interior. Thanks
-
- 0 replies
- 2.9k views
-
-
I know the standard finish for cutting boards is mineral oil or mineral oil/beeswax. I've never actually seen or felt a board with this finish, so I'm wondering what they feel like? Do they have a greasy feel? I just finished two large end grain boards and finished them with Tried and True Varnish oil, and they look great, but it takes forever for them to cure, so I'll likely try MO next time, but I'm concerned about how they feel. Thanks in advance for any insight...
-
- 8 replies
- 3.1k views
- 1 follower
-
-
I recently got an old chest of drawers off of my aunt. The finish is old and I was thinking of stripping it off and restaining it (or painting it - I like the colors you get from milk paint). The drawer fronts have this....interesting finish that is basically 3D at this point. I've been told it's called an "alligator finish" and is what happens when the lacquer(?) they used back in the 20's and 30's gets repeatedly exposed to cycles of heat and humidity. Is that the case, or would someone have finished it this way on purpose. Other than some veneer peeling off the top, the piece seems to be in a good state construction-wise, and is solid with great proportions. NB-…
-
-
- 9 replies
- 3.1k views
-
-
I'm about to start on my kitchen cabinets and I'm planning on a painted finish. That said, I do not want to brush these things (I hate painting, my pantry took way too long to brush). I'm willing to buy a gravity feed HVLP gun if need be or use my grandpa's old Binks siphon gun. I have a decent sized air compressor that I feel will be adequate to get the job done. That being said I'm in need of some help from you guys, probably @wdwerker would know a lot about this. What paint can I use to get a good long lived finish in a kitchen? It needs to be tintable as I'm planning on doing the uppers in white and the lowers in some sort of blue grey color (whatever my fi…
-
-
- 12 replies
- 5.8k views
-
-
Hello there! I only have a small number of projects under my belt thus far. I haven’t really stepped into the world of finishing yet so I have much to learn. Recently I built a simple desk surface for my home office. I used baltic birch ply and added some walnut to the edges. I’m not sure what to do about the finish though. There are two things on my mind. First is how to finish it so the natural qualities of each wood are brought out. The second is how to “protect” the material as it gets daily use in my home office. I’m not sure how to research these things, so I made my way here hoping to find either suggested learning resources that can get me going OR …
-
-
- 8 replies
- 3k views
-
-
I am assisting a friend build an table top to place on some wine barrels to make a "bar" type table. The table is approximately 4ft wide by 8ft long. It was built out of 2x6 cedar from home depot that was laminated together. I've finished the glue up and sanding. So it is time to stain and finish. A minwax stain will be applied for some color, but I am having a tough time identifying what would be the best type of finish. Ideally this table top will live outdoors all year long. It is unlikely to get wet or receive much direct sun exposure at all since it will be under a covered patio. I did some searching around and saw this article, https://www.thewoodwhisperer…
-
-
- 12 replies
- 9.2k views
-
-
I’ve been doing a lot of Mission finish projects lately. Most of the recipes out there call for Seal-A-Cell after applying the dye. I have been substituting Bulls Eye Seal Coat because I had several cans that needed to be used due to limited shelf life. I’m working on two more pieces that will have the Mission finish and I don’t have enough Seal Coat to complete these. Has anyone experienced a difference between the two? The Seal Coat has worked well on the pieces I used it on, just wondering if Seal-A-Cell gives a better look/finish.
-
-
- 11 replies
- 7.6k views
-
-
I am finishing a large kitchen counter, new construction, and applying Arm r Seal. Due to the size, I typically spray my finishes. After the first coat was applied, then sanded before second coat, bubbles started appearing within about 1 minute of completion. I’ve lightly sanded subsequent coats and tried different methods, including foam application and canny get rid of the bubbles that dry, leaving a horrible looking finish. I have followed the manufacturers specs, and no luck. I have thinned with mineral spirits and brushed on, no luck. This is all in a dedicated spray room with 74F and 50%RH. I am at a loss on what to do and welcome ideas and feedback. My next st…
-
-
- 28 replies
- 11.8k views
- 1 follower
-
-
I’m in need of some advice. I’ve built a coffee table sized shadow box for a coworker and upon unboxing she discovered the top surface had blistered. It is made of cherry with maple accents. The top field and major carcass components are made of 3/4 cherry ply and the frame surrounding the top field is approx 3” solid cherry. For finishing I applied an initial sealer coat of dewaxed shellac (zinnser brand) followed by three coats Sherwood Lacquer. I knew there would be a little bit of time between completion and delivery, and since it would be living in my dining room for about a month, I added a couple coats of Briwax to the top. Yesterday I wrapped it in bubble wrap, b…
-
- 4 replies
- 4.4k views
-
-
Hi everyone - first post, first wood work ever, and a lot of learning along the way. So, i'm refinishing my outdoor table which is in a pretty bad shape. Lots of cracks to be filled with. i'm following the instructions on the video about refinishing the outdoor table. I started from one of the benches, so if I mess up, I won't mess up the table itself. The thing is West System epoxy is super expensive, and I think I'll need a lot of it to fill all the cracks in the wood (it spent 2 years without any outdoor finish exposed to the weather). Any alternatives that have good quality, but are more affordable than West System epoxy? Thanks!
-
-
- 16 replies
- 9.8k views
-
-
Two easy questions with potential one word answers: I have a new beech wood mallet that will benefit from an oil finish. A web search finds many references to using Boiled Linseed Oil for mallets with BLO sounding like a perfectly reasonable choice, so naturally I don't have any BLO in the garage. However, I do have a can of Tung oil. Would it be a mistake if I used the this instead? Might the Tung Oil actually be a better choice?
-
- 6 replies
- 5.4k views
-
-
Hi Everyone, I'm new here so forgive me if this is covered somewhere and I just haven't found it. Also new to inlay which I am doing with a small music box. The wood is simple pine (I think) and I carved out stars on each side. I then mixed blue glow in the dark powder with epoxy and filled the star cavities. Have sanded down the dry glow epoxy to be level with the surface. But I'm at a stuck place now and hoping someone might have some suggestions. I would like to stain the box so it is a darker color, I think it would cause the glow stars to pop out a little more. But will the stain dull/cover my filled in stars? Also I would like to add a small …
-
-
- 7 replies
- 3k views
-
-
Hi folks - I've built eight tables for my wedding reception that's coming up 16 June, and wanted to see if I should take a different approach to their finish than what I currently have in mind. I obviously have some time constraints given the date is looming closer by the moment so multi-day coating and surfacing programs are not going to work. Long story short, I am loading these tables into a trailer 10 June and driving them up to Pender Island in British Columbia the next day, so ideally I would like to complete the finish application tomorrow (8 June), let the tables cure for two days, and be finished with them so I can focus on my many other wedding tasks. I pl…
-
-
- 27 replies
- 7.6k views
-
-
Hi there - I'm a total newbie at wood staining/finishing (beyond just basic deck staining). We are building a new house, and silly me, I offered to stain the cedar tongue and groove planks that will be used on the ceiling and walls of the porch - not realizing this would consist of 79 boards that are 14' in length. I also didn't realize I would be given a very short time frame to get this done (like, a few days). Yikes. I live in WI, so the cedar/screen porch will be exposed to significant temp changes and humidity, but it will not be in any direct sunlight. I went to SW, and they recommended BAC wipe-on stain. That went on beautifully, and that part of the proj…
-
-
- 7 replies
- 6.2k views
-
-
My Morris chair is coming close to being finished but I can't decide what finish to go with. I was at first going to do the same as Marc...a wipe on varnish followed by lacquer. I had some second thoughts and bought a pound of garnet shellac, just in case. I just bought a Fuji MM4 and am heavily leaning toward spraying whatever I choose. Points to consider...The chair is cherry. Straight grained as well as I could with the material I had to work with and flat sawn arms. It will only really be contacted by skin on the arms, nothing else will really be handled. We do have a Roomba, so that thing will bounce off the legs pretty regularly. I do have a 2 1/2 year o…
-
-
- 9 replies
- 3.2k views
-
-
I'm making a coffee table for a friend. He would like a dark walnut color. Problem is, I just finished a major walnut project and the material is just too darn expensive for me right now. So I built the piece out of Cherry. I know cherry is beautiful on its own and I know it darkens with age, but I'd like to deliver something that is a bit darker on arrival. To that end, I purchased some transtint dye, which I've never worked with before. I mixed up some dye with 50% Water, 50% Denatured Alcohol and applied with a rag. It seems to darken the wood immediately and dries very fast, but it does seem to be a bit uneven, with dark and light areas. Should I be lookin…
-
-
- 8 replies
- 5.8k views
-
-
Howdy, It's been awhile since I've refinished anything, and this is my first real "big project." I sanded and refinished my dining room table and the leaves using minwax oil based stain. I applied the stain on the leaves outside in ideal (sunny) drying conditions. However, the weather started to turn and I had to finish the table over the course of a week outside under a tarp while it rained all around (UGH!). So I think I have some moisture trapped in in the stain causing some white haze or patches. See the pics. I've already done 4 coats of minwax oil based wipe-on poly per the instructions hoping it would fix itself. Alas that has not been the case. Ideally …
-
-
- 1 reply
- 5.5k views
-
-
Have neglected hardwood floors; guessing poly coating. 20 years old. I am renting, and not yet ready to sand and refinish. Is it safe to use Watco Danish Oil on floor as a stop-gap to partially restore luster? Can I use Bona or Swiffer Wet Jet on it to clean, if I use Watco Danish Oil? Any other floor restorer without sanding recommendations? Thanks.
-
- 9 replies
- 11.7k views
-
-
This project represents several firsts for me - 1) First acoustic guitar from scratch. I've replaced tops, backs, bridges, saddles, nuts, done inlay, repairs, etc. but this is the first one from scratch - resawed the wood, bent the sides, etc. 2) First time to do a French polish from the start and not just a repair. 3) First time I've made this many mistakes in a project and kept going, trying to figure out how to successfully fix what I've done and trusting it's still going to work out ok. So here's the sanding tip I learned a long time ago and I have no idea if it's something I read, something I figured out, or even if it's common knowledge - It takes twice …
-
-
- 9 replies
- 3k views
- 1 follower
-
-
Can't figure where to put this, but it seems worthy of sharing. I often stick a brush in a jar with solvent while waiting for a finish coat to dry. Usually I shove a rag in around the brush, but in this case the nitrile glove was what I found nearby. It fits over the brush handle. (Bonus tip: I cover my jar label with packing tape to protect it from solvents.)
-
-
- 3 replies
- 2.8k views
-
-
I’m working on finishing a pair of bookcases I built for my wife. Using rattle can poly to seal it in. I have sprayed 2 moderate coats on the cases and shelves. Just sanded the first case down with a fine sanding sponge. Does a third and final coat need to be applied for the finish o be done correctly? Or will two coats be fine? I ask because overspray is an issue with my current set up (in the laundry room with a shop vac and a window as my only source of venting). So I’m almost positive that if I spray another coat, it’s going to be rough again. Sent from my iPhone using Tapatalk
-
- 10 replies
- 3.4k views
-
-
I'm a rookie and am building a large fir table for the back yard, my wife wants it stained darker and I want it to withstand the elements as best as possible. Can you advise what type of finish will be best. Understanding it will require maintenance. the eventual plan is for it to be under a covered structure. Also would you recommend finishing parts before assembly? pics attached.
-
-
- 4 replies
- 3.4k views
-
-
Hi I am making a small cabinet to go next to my utility sink and an am making the top ou of some left over walnut I have. The cabinet will take some abuse like wet items that have just been cleaned, brushes, buckets, containers etc... I am looking for a way to make the top as durable as possible but keeping the natural wood color. My idea is to apply a epoxy top coat which I have done in the past but this top is different. I am going to rout and edge with an ogee or some other edge bit. The issue is how do I epoxy the top and keep it level and keep the edge from looking sloppy? Here is and idea of the type of edge I plan on doing to the top. Or if there are…
-
-
- 11 replies
- 3.8k views
-
-
I’m applying Tung Oil on dark walnut. Sanded to 150 grit. Applied the oil, let sit for 20 mins. Wiped excess off. A day later when it dried I rubbed my finder on it and there is a waxy film. I’m able to buff the film off but it’s a pain. I’m going for a food safe finish on serving boards. Am I doing something wrong? Need some help.
-
-
- 17 replies
- 7.4k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·