Jig & Fixtures
Build jigs and fixtures for safer, more repeatable cuts. Share table saw sleds, router templates, drill guides, and custom workholding setups.
489 topics in this forum
-
I will be making a some cabinets in the near future and wanted to see if anyone had some ideas for a jig to help me place the drawer slides. Or does anyone have any experience with one of the commercial products like Kreg?
-
- 5 replies
- 9.9k views
-
-
I don't have a drum sander, but I do have a planer. When I am cutting layers for lamination, resawing, or keys for a joint, I can only get as smooth a cut as my bandsaw will work with me. If I had a drum sander, I would just shoot a piece through there to get a nice smooth surface. I have heard that you can put a board under your thin piece to get the piece above the planer's minimum depth. I would like to try this, but I have no idea what this sort of jig might look like. If I am looking for 1/8" final width, how to I make a jig so that I can make that a repeatable procedure? how do I keep the thin board from shooting all over the place when the knifes hit it? I unde…
-
-
- 7 replies
- 7.2k views
-
-
Will my Hitachi M12vc router work with the template on this jig?
-
- 2 replies
- 5.2k views
-
-
Gotta make a cross cut sled for the table saw. I was thinking of making it left of the blade only, out of MDF. Let me know what you think Stampy
-
- 26 replies
- 16.8k views
-
-
http://makeprojects.com/Project/Router-Trammel/743/1 I like this take on the router trammel. Using the 8020 extrusion as an inexpensive, robust, ajustable arm is neat idea.
-
- 0 replies
- 4.8k views
-
-
What are the pro's and con's for plywood/MDF use in jig making. A few things to consider would be; ease to build, price, availability, durability, would one build a more precise jig? What do you use for your jig making needs, use the poll to vote but please also add your comments.
-
-
- 11 replies
- 14.3k views
-
-
I just made this mortising jig from on Youtube. It is simple to make and works good. I can already see that I will need to make some modifications to make it quicker to set up for repeated cuts, but it gets the job done on the cheap. I use the planer to make the right thickness for the tenons and a router to round the edges of the tenon to fit the mortise. I also made one for my Dad.
-
-
- 9 replies
- 10.3k views
-
-
Hello, Ive been thinking about building a crosscut sled for my table saw. problem is i have this crappy little craftsman with a f**ked up miter gauge. So I thought I could build support onto the sides of the table itself. any ideas of possable problems with this rig?
-
- 6 replies
- 6.4k views
-
-
I am making little mementoes for the 50th reunion of my college graduation and have to make 30 small (6"x6") picture frames. Does any one have plans for a reliable picture frame jig I could use on my table saw?
-
- 3 replies
- 5.9k views
-
-
So I figure what better idea for a first post in a new forum than suggestions on what would be a good first jig to make. What jig have you found most useful across projects? I'm thinking that a crosscut sled would be useful, and this seems like a great plan: http://www.woodsmith...rosscutsled.pdf What do you guys think?
-
- 6 replies
- 4.8k views
-
-
Another plan that I found on the web. When the router fence is installed, it should be positioned so that the flush trim bit is centered in the slot. To use this jig, place your piece in a vise, with the edge banding up. Place the jig so the router table extends to the rear of the piece. The router then slips down into the slot, and is Pushed from Right to Left. This is important as you are routing on the back side of the piece. If you go Left to Right, this will be a climb cut, and you may lose control of your router. Again, I cannot take credit for the design, only for the SU drawing. Roger Edge Trimming Jig RO.skp
-
- 0 replies
- 5.8k views
-
-
Since I asked for this forum, I figured I had best contribute to it. Anyway, here is the spline jig that I made a few weeks back. I had found a basic plan on the Web, but could not locate it again, so I have done it in Sketchup. The fence is movable, and is secured with a couple of small clamps. I did not draw the runners for the tablesaw, as each saw is different and uses different measurements for the slots. The jig should be centered between the 2 innermost supports when you attach the runners. I cannot take credit for the design, only the SU drawing. Roger Spline Jig RO.skp
-
- 0 replies
- 4.8k views
-
-
Well, just as it sounds, I am in the market for a dovetail jig. I am in the process building kitchen cabinets for my brother-in-law and this is a perfect excuse to get a new tool. While I am looking for to cutting dovetails by hand at some point, I dont want to do a whole kitchen by hand, especially when they are going to be made from ply. I am only looking to buy one jig, and the fewest templates, so I want one that can do through, half-blind, both of those variable spaced. I know that this limits my choices, and also makes those choices more expensive, but I need to get as many uses out of this as possible to justify the expense to the wife. I am thinking that …
-
- 7 replies
- 7.4k views
-
-
Im not sure if im posting this is the right place, so mods, please move if necessary. I would like to get a dovetail jig. just like most of you here, i recently got the new rockler catalog with their dovetail jig on the cover. the complete kit is on sale for $119 which seems like a great deal. it comes with a brass bushing, router bit, and the jig itself. does anyone have any experience with this jig? hard to pass up this price.
-
- 7 replies
- 7.9k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·