Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Jig & Fixtures

Build jigs and fixtures for safer, more repeatable cuts. Share table saw sleds, router templates, drill guides, and custom workholding setups.

  1. Started by Spencer_J,

    Looking to work with dovetail splines in an effort to make different shaped splines etc. I feel like I saw somewhere in a catalog a nice plastic template with some different shapes and sizes of dovetail splines. Any idea who sells them? I've looked everywhere it seems.... Thanks!

      • Like
    • 11 replies
    • 6.6k views
  2. Started by wgeils,

    I think I've got myself in over my head. I am tackling a project that has a couple of steps that I can not figure out. I need to make a bunch of repeatable angled dado's for a project I am trying to do. These cuts are intended to be a groove that a 1/4" piece of plywood will slide in and out of inside of a display case. I am having a hard time setting up a jig that will allow me to crisply make this cut in a repeatable fashion. That I then can flip to make the mirror cut for the other side of the case. Dose anyone have plans for a jig that I can build to help me do this? I am rather new to working with my router so assume that the only thing I've mastered on it is the…

      • Like
    • 6 replies
    • 4.8k views
  3. Started by dwacker,

    I didnt know where to put this so "jig &fixtures" sounded about right. I sold my Lamello glue system and started using bottles, I regretted the decision right away. Rather than spend another $1000 to buy another Lamello I decided I could just make my own. A pressurized glue system is nothing more than a pressure tank, hoses and a needle valve nozzle with tips. You can make these things as fancy as you want. You can buy nozzles for as cheap as $100 from CAT the makers of finish spray guns. Lamello will sell you theirs for $200 and GMC will sell you one for about $150. The idea was to do this on the CHEAP. Nothing will be fancy in any way not even the gun. I don't int…

      • Like
    • 15 replies
    • 10k views
  4. Started by tdale51@yahoo.com,

    I just made a circle cutting jig for my bandsaw and thought I'd try to post pics and somewhat of a tutorial here. Maybe someone will find it helpful. I got the original idea from a video on youtube, I think it was put out by Woodworkers Guild of America. First I measured the width and depth of my bandsaw table (16" square in my case). Then I ripped a piece of 3/4" MDF to the depth of my table and cross cut it originally to 30". 30" proved to be too long so I cut it down to roughly 26". Then I set my tablesaw bevel at 45 degrees and my rip fence to 1" less then half the width of the piece of MDF (7" for me) and ripped it. The resulting ~7" piece got set to the sid…

  5. Started by pghmyn,

    I had to cut some tenons for tongue and groove joints for some cabinet door rail and stiles. I did not have a good method of removing the vertical waste effectively since I would have to do it 32 times. At the time I did not have money for a commercial tenoning jig, so I thought of a plan to make one myself. It started with my table saw sled. Although crude looking with a sheet of MDF and a 2x4 stud, it is deadly accurate. It is jointed on two sides. The side which attaches to the MDF, and the side which touches the workpiece. Absolutely straight, and perfect 90 degree angle to the blade and MDF. https://www.dropbox.... 3 01 51 PM.jpg I thought that since this sl…

  6. I was clicking around and found this: http://www.infinitytools.com/Rip-Cut/products/1821/ I got one- with shipping it was like $12. I have some plywood to cut so it's either going come in handy or not but for $12 I had to give it a shot. Make it a great day.

  7. Started by SRF12980,

    I HAVE SEEN THOSE METAL PLANER BLADE/KNIFE SHARPENING JIGS, AND ALTHOUGH ACCURATE, THEY ARE COST PROHIBITIVE. I DO SHARPENING HERE IN NORTHERN NY FOR THE HOMEOWNER AND CONTRACTORS AND NEEDED TO MAKE A JIG FOR THOSE DISPOSABLE DOUBLE EDGE PLANER BLADES. I SQUARED UP A PIECE OF HARDWOOD ON A SURFACE PLANER AND CUT A 2 INCH SQUARE PIECE ON A TABLE SAW, THEN CUT A GROOVE IN ONE OF THE CORNERS ABOUT 7/16" DEEP. THE DULL KNIFE FIT INTO THE GROOVE AND HELD THE KNIFE AT A 45 DEGREE ANGLE. MY EARLIER CONCEPT USED WOODEN WEDGES SPACED ABOUT EVERY 2 INCHES ALONG THE BLADE TO KEEP IT SNUG IN THE JIG. THE JIG AND BLADE WAS ROTATED SO THAT THE UPPER CUTTING EDGE OF THE KNIFE CONTACT…

    • 5 replies
    • 5.5k views
  8. Started by rbbauer00,

    There was an episode of Woodsmith Shop where they made a miter gauge setup jig. The jig allowed instant setup for a left or right 45, or a 90 degree setup. Basically it was a square piece of plywood with two parallel dadoes and a 45 degree right triangle on top. You then just put the gauge in the dado and slid it against the triangle to set the angle. They did this at the end of the episode (where they give random tips that have nothing to do with the project that the episode was about). Does anyone remember which episode that was? Obviously I want to make this jig, which seemed simple enough, but I wanted to see again how they made the "T" slot, as well as how th…

  9. Started by Keith Gallagher,

    Hi all. I am a first time poster here but hope to spend many evenings here talking wood with fellow woodworkers. I am from Ireland and I am looking to get the mentioned item for my Jet tablesaw. The problem is for some reason they can not be shipped to my address. Is there anything about why that is? Is it because of Health and Safety regulations here or what could it be? I am also looking at getting a longer spindle for my saw for dado blades but I think this may be the same problem as the jig, not allowed on this side of the pond. Anybody got any ideas?

  10. Started by dustman,

    I am a member of an online blind woodworking group (http://ww4b.org/). We have been discussing cutting octagons. We hsave a lot of smart guys and they have the math down great. I found several jigs for cutting octagons including the one at Fine Woodworking. If you cut octagons what method do you use to ensure equal sides.

  11. Started by Dave H,

    Now I've used many diferent methods for cutting circles, I like router jigs for large circles, but for smaller circles I turn to my tablesaw, and a homemade sled. Here's my video of this jig in action you get a very accurate, and smooth finished circle with this method. The video has to much backgound noise, so in the part where I'm spinning the piece into the blade what I'm trying to say is I take light cuts, than I advance the sled slightly than spin again until the is no more material being removed.

  12. Started by Jjmedure,

    i want to make a shooting but i seem to get a little confused when looking at plans. It seems pretty straight foward and simple but the part tha confuses me is from what i gather the blade will be riding aganst the the wood that should be keeping the plane at 90 degrees. It also seems like it would ride aganst the stop that is holding the piece you are planing. By doing this wouldnt the plane cut into both pieces of the jig? Might be a dumb question but its my question! Thanks in advance!

  13. Started by TRBaker,

    I am frequently asked to make A/C registers and return grills out of different species of wood. Some of them are for floor registers in hardwood floors or antique pine floors. Also, in rooms where the walls are wood instead of drywall, it looks so much nicer than having an aluminum grill. Using a simple box joint sled makes this a lot easier than you might think. Here are a few projects I've done using just the ts and a sled.

  14. Started by joelav,

    I needed one of the thin rip jigs rockler sells. I hear they work pretty well. Instead of buying one, I made my own. Not because I am cheap, the rockler one is under 20$ I think and it gets awesome reviews, I just really enjoy making things. If you want to make one of these here are a few good tips: 1 - 45 degree cuts coming to a point at the tip do not work. It's very easy to nock the jig loose 2 - A flat spot at the end of the angled cuts at the tip works better... BUT it makes 90 degree alignment absolutely critical. The last thing I want to do is spend more time microadjusting something so.... 3 - A flat spot at the end with a bearing in it works awesome. I used …

    • 2 replies
    • 5.9k views
  15. Started by Nickthewoodworker,

    Anyone have any ideas on how to make your own kreg jig because I want one but don't want to spend 150 for one

      • Like
    • 15 replies
    • 6.9k views
  16. Started by Jerry_in_SD,

    I am starting a kitchen project soon. I purchased one of those Kreg rip saw guides on sale when it came out without any reviews. Had it cost more than it did I would not have done this. I plan to use it to rough cut ply before going to the t saw. Anyone have experience with this? Would like opinions before I tear into moderately expensive per-finished maple ply that will make up my boxes.

    • 6 replies
    • 4.8k views
  17. Started by Sylvain Ward,

    I'm trying to build a finger joint jig (the one in the last shop note magazine) and i need a T-track to secure the keys on top of the jig. I've looked everywhere but i can't find a T-track anywhere and i don't want to pay 50$ for shipping a 10$ piece of metal in canada. So I was wondering if anyone as a suggestion for anything that would do the job? At this point i'm probably just gonna screw the keys in the jig for a temporary solution.

  18. Started by Dave H,

    I'm in the prosses of building a disc sander for my lathe here are some pics, attachment=6498:P1000559.JPG] The disc sander is a four piece unit the first piece slides tight to the power head of my lathe The second piece is the sander itself mounted to it's own face plate the third pieces slides up tight to the first piece and the large plywood washer/wing nut holds the whole unit to the bed of the lathe it's still a work in process the table will be a single layer of MDF with a miter slot possably formica for the final top finish, the dust shroud was made doing bent lamination and slide into the slot of the first piece

    • 6 replies
    • 9.5k views
  19. Started by Dave H,

    My old plywood cutting jig finally went on the burn pile it lasted me many many yrs. here is my newest and mor portable version, and just like the last cutting jig it doubles as a portable router table that I take to job sites when I need a router table. The cutting jig breaks down, leans against a wall, or loads into the back of my truck for any job I may be doing, the old one was all one piece, and sometimes was a pain to load in the truck I like this idea better I can't remember who I stole this idea from but the knock down version was'nt my idea so thanks to someone either here or lumberjocks. the great thing about the plywood cutting jig is when your cutting plywood…

  20. Started by joelav,

    I like to make jigs. I especially like to make jigs that fit in my jigs. I made this spline cutting jig to go in a cross cut sled. The sled is based on John Nixon's design from eagle lake woodworking. it's actually an old one that I stripped all the hardware (t tracks, blade guard, dust collection) and what not off of and was about to cut up. It attaches to the cross cut sled with track clamps.It's ugly, but it works. I needed it to get me through a box project. Now that I know it works really well, I am going to make a nicer looking version with cut outs on the sides to allow for larger boxes

  21. Started by rmac,

    All the talk in the recent thread about racking vises and spacers to prevent same inspired this little gizmo. The idea of course is that you can easily make any size spacer you need just by rotating the leaves in and out of the way. The 3/4" thick blocks on each end of the bolt keep the thing from falling through the vise while you position your workpiece with one hand and snug up the vise with the other. -- Russ

      • Like
    • 19 replies
    • 7.8k views
  22. Started by Coweyeboy,

    I'm having a hard time deciding which kreg kit to buy. I see there's a $140, $100, $40, & $20 kit. Im only making a foldable workbench, but, I'm also looking to make home furniture like shoe racks and shelving. Do I dish out the $140 or can I settle for just the $40 kit? Thanks

    • 14 replies
    • 14.1k views
  23. Started by rodger.,

    Do any of you guys use bench hooks for fine tuning small pieces?

  24. Started by modela,

    I am a fan of jigs. You can usually make them quickly for repeatable events and produce professional results. One of the challenges of the Pisgah project was drilling sets of four holes at the joints. There were from one to four 3/4" bolt holes that had to be drilled through five layers of 4x material (18") using a 13/16 bridge auger. The proposal was to drill them individually but I knew that with my drilling the likelihood of them coming out straight was pretty unlikely. I proposed making a jig. My fellow workers thought it was a waste of time and the idea was met with some resistance. It was Friday afternoon and no work had begun so I decided to build the jigs on my…

      • Like
    • 1 reply
    • 3.4k views
  25. Started by mds2,

    I didn't have a good way to cut miters on the edges of boards. I have an older Craftsman table saw and while I think it is a pretty good saw the blade will not tilt all the way to 45. So last night I made a miter sled. It isn't quite finished, I need to add a hold down yet. I am happy with the jig though. It cuts miters easily and if I flip the board over and lower the blade I bit I can also cut notches for splines.

    • 3 replies
    • 4.7k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.