Jig & Fixtures
Build jigs and fixtures for safer, more repeatable cuts. Share table saw sleds, router templates, drill guides, and custom workholding setups.
489 topics in this forum
-
Here's a video that I recently filmed, showing how I make pinch sticks. These are great for assuring that your assemblies are square during glue-up.
-
-
- 3 replies
- 4.8k views
-
-
Looking for opinions here. Just finished my router table build, its topped off by a incra table top (24x36). I know I can build one, just not sure I want to. So looking for opinions on what RT fence you would buy if you were in my position. Best combination of features vs price. I don't want to put any tracks in my table top for fence hold downs, so the fence would need to hang over the side of the table top a few inches in order to clamp it down. I've looked at Kreg, Woodpeckers, Incra and JessEm fences. I'd love to have the full Incra set up with the joinery jig attachments, but have read some negative reviews. I don't mind putting the money into it, but if…
-
-
- 19 replies
- 6.6k views
-
-
Loaned mine out and guy fell off planet. 3/8 thick 36 long 8 wide aluminum. 5/8 router bushing 32mm spacing True 32 stops Blum stops Clamp holes I'll bore the stop holes in next day or so.
-
-
- 8 replies
- 4.5k views
-
-
I saw the usefulness of a Boom Arm for my Festool CT26 but the size, complexity and price scared me off. Decided to make my own. I made a box to fit around a Systainer that is latched into the top of the Vac. Post is attached to one corner of the box. Scrap of piano hinge, plywood triangle brace, arm is scrap of the post. 15 minutes to build w screws. Box just slip fits over the Systainer. I used 1/2" baltic scrap and a 1 1/2" square piece of oak for the post. Bungie cord hangs the hose. Stretch wrap helps too sometimes.
-
- 6 replies
- 7k views
-
-
Went to an estate sale on Sat. Got some goodies and some stuff I don't need, as things always go. The first jig I cannot figure out. The block on the front is roughly 1 width of the kerf away and the marks on top are 1 kerf away to the other side, with the top movable. It has two plastic 3/4" guides on the bottom. I'm keeping it around just in case ... The two fences were in the same stack. After work today I got my saw out to check blade alignment (fortunately OK) and then align the protractor fence. I can see why they frustrate people. Took a while to get it right on and "right on" does not exactly match the scale. Oh well. Right is right. Worse case I ca…
-
- 6 replies
- 3.5k views
-
-
Is not a crime and should be done every time. .. In preparation to glue up 4 sides to jewelry boxes, I stopped and built a jig to help keep everything aligned and easier to clamp. The jig worked great, for making left sides. Once all 4 sides finished drying, I set the sidesto realize I had made 4 lefts. . Ugh. The legs are asymmetrical and I didn't take it into consideration when making the jig.. The crappy part was that the legs were all book matched and now won't be once I make two right sides.
-
-
- 11 replies
- 3.9k views
-
-
I needed my bandsaw sled this morning and again it was having a lot of play. I sanded the runners the last time I used it because the sled was to tight, that must be it. Instead of making new runners, I decided to go for a more permanent solution. My bandsaw table has two 3/8 holes on the right side, for attaching an extension wing. I attached a drawer slider to a 2x2 section and then attached the 2x2 to the table using 3/8 hardware. Finally I set the sledge on the table, made sure it was square to the blade, and screwed it to the slider. It's a simple design, I can take it out and put it back really easily. The hard part was the accuracy required to make …
-
-
- 4 replies
- 4.2k views
-
-
Can I cut the slots for the splines before gluing the joints? Was thinking about something like this: I don't currently own a table saw.
-
-
- 21 replies
- 11k views
- 1 follower
-
-
Got a call from a friend who's selling this jig. He said he never used it, so everything is supposed to be brand new, router bits and all. He's giving me a good price. But I don't want to buy trash, even at low prices. I think I could use it for my box joints, just because it seems easier to setup than my Incra fence (due to lack of space I cannot have my router table ready to use at all times). What do you guys think? Any owner who can share his experience with the jig?
-
-
- 12 replies
- 4.5k views
- 1 follower
-
-
i dont know if this is only under the subscription, but here is another FWW site. this is a whole page of jigs http://www.startwoodworking.com/jigs
-
- 9 replies
- 6.5k views
-
-
Got myself a cute little Delta drill press as a starter setup. It was nearly unused and pretty much brand new for a very good price. I couldn't pass it up and it's just right for what I need for now. I needed to make some sort of table for it, and figured I'd make one with a fence as well. I really liked this design and it didn't require anything fancy. The use of the toilet bolts was also a great idea It's a bit much for this little press, but I figure I can always use it on a bigger press and it was a pretty simple build.
-
- 4 replies
- 4.3k views
-
-
I am curious if you would say any certain type of jigs would almost be a necessity for every shop? I know most jigs come from not having certain equipment or doing something unique ... but I was just sitting here drawing out some jigs I am going to create this weekend and it got me to thinking about everyone else. I am going to make a straight edge, router, and a 45 degree inlay jig ... I know the last would not be a necessity in every shop but I think the first 2 would be very helpful. Plus I am also assuming most people dont have a jointer/planer as well .. like myself
-
-
- 19 replies
- 7k views
-
-
I have a very tall 1x6 T&G Cypress sided wall that I need to repair. I wondered if there is a jig made for my oscillating saw that would allow me to surgically remove staggered lengths without damaging the neighboring boards and leaving a 45 degree back-miter I can slide the new pieces up to.
-
-
- 4 replies
- 3.8k views
-
-
HI guys, I'm fairly new at this and I'm looking to make the crosscut sled from the Woodsmithshop.com http://www.woodsmithshop.com/download/403/precisioncrosscutsled.pdf The first thing it talks about is whether your saw is left or right tilting. They say if it tilts to the left, you need to make a mirror image of the sled in the plans. I can't get my head around this. The sled has an adjustable width blade slot to accomodate dado blades - and tilted miter cuts. In the plans, this adjustable section is to the left of the blade. The fixed section is attached to the miter bar running in the slot to the right of the blade. My saw tilts to the left. That is…
-
-
- 6 replies
- 5.2k views
-
-
Thoughts on how it compares to other dovetail jigs?
-
-
- 15 replies
- 10.2k views
-
-
hey guys! New to this forum, but I've been watching all the videos on here for quite some time and learning a ton. Thanks again marc! Anyways i was wondering what was a good way for making a box-joint jig? i was going to pick up a router bit but is there a better way using the table saw? I plan on making some recipe boxes this Christmas and i think it'll look classy with some good old fashioned box joints. Thanks in advance for reading this!
-
-
- 11 replies
- 8.1k views
-
-
Just heard about these things from the latest Highland Woodworking newsletter (i've really got to stop reading those things...). On rare occasions i've ordered one of the OneTime tools, and i'm slightly tempted again by this one. But like all their OneTime tools, they're not cheap. http://www.woodpeck.com/ottsetup2014.html What do you guys think about these setup blocks? Useful? Or just one more item to keep track of and clutter the shop? Some of the functions i can do with my adjustable square. Others maybe not as easily.
-
-
- 41 replies
- 16.6k views
-
-
Made a badly needed strait edge jig over the weekend. Clamps on sale at Rockler $3.99 each, $20 for all the Track , $12 for the steel , $40 for the board works great ! .
-
-
- 11 replies
- 7k views
-
-
I made a template out of 3/4" MDF to route some circles. After routing a handful or circles, I noticed that the bearing on the bit had kind of pushed a channel/groove into the inside of the hole in the template. This causes a little bit of a problem if I don't set the bit depth the same for multiple passes at different depths, because it then traces a slightly different circle and leaves a ridge inside the hole that is routed. Is there any better material than MDF to make a template like this from? Plywood wouldn't probably squish like the MDF did, but it has its own ridges that may or may not be a problem. What do you guys usually use for router templates like this? …
-
- 21 replies
- 8k views
-
-
In the process of setting up my shop and reviewing what is left on the list for my initial table saw accessories...tenoning jig is at the top. Ever since seeing good old Norm use it for all his tenons, I haven't seen a better (cost vs speed) way to do this task but would be open to hearing suggestions. That said, I'm pretty set on buying one...but cannot figure out which to buy? It seems like every one has positive and almost equally negative reviews. So far rockler, grizzly, and jet seem to be the better of the options...with Jet being the more expensive outlier. Any suggestions based on actual use? Thanks, Ted
-
-
- 10 replies
- 5.8k views
-
-
There is an abundance of "Solid Surface" counter tops being both put in and remodeled these days. Most is now granite and quartz with a still a bit of Corian. The one thing I love about making jigs out of solid surface materials is that here in Florida, they don't warp or have issues with humidity. I can leave them is the shed with out worrying about heat or cold. I have made a great deal of stuff out of corian using free great looking material out of the trash bins of counter top fabricators. The best are of course the sink cut outs which make great cutting boards. As in this example, super glue is kind of what this stuff is made of anyway for 90% bends are easy and …
-
-
- 12 replies
- 7.4k views
-
-
Hi folks, I am helping a friend build a mantle clock using plans he purchased. Had we read the directions more carefully we would have seen that we should have cut a large rabbet in a long piece and then cut the pieces to length and then mitered to make the face frame in which the mechanism resides. But now we are in a situation where we need to hog off a large rabbet off a piece that is 1 3/4 inches wide, 5 5/8 inches long, and 3/4 inch thick. The resulting rabbet will leave the frame 1/4 inch thick by 3/16. Had we used one long piece I would feel much better about a dado stack or standard blades and make a small cut in and then the tall cut to free the waste. But with…
-
- 15 replies
- 5.9k views
-
-
Our cupboard doors all got mounted this weekend. Things are looking good, in general. But after mounting I noticed a difference between the original hinges and the replacements. (Replacements: http://www.homedepot.com/p/Hickory-Hardware-Satin-Nickel-Self-Closing-Hinge-2-Pack-P243-SN/100674849 ) The new hinges make the door stand out a bit. It looks like I need to mortise the backs. That's a project for the Spring. It looks like what I need is a jig recommendation.
-
-
- 1 reply
- 3.3k views
-
-
I've been getting ready to build a Longworth chuck for my lathe beamer from the live chat made a bunch of them for some of the guys on live chat on his CNC so I did some research and I'm going to try and build one with my router and a home made trammel jig. The Longworth chuck will be made out of 1/2" baltic birch it will have a 2" dedicated face plate. Here is a picture of what I'll be making I got #6 1/2 bottle stoppers for project yesterday I bought the solid rubber(no hole in the middle) all the pre-drilled ones I found had 5/16" holes and I already have the hardware for 1/4-20 bolts so I had to drill a 1/4" hole perfectly centered all the way through the stoppers …
-
-
- 3 replies
- 7.3k views
-
-
I am looking to build a sled for the table saw. I plan on doing cross cuts as well as dado cuts. Should I make two different sleds? Is the dado slot in the sled too wide if/when making cross cuts?
-
-
- 13 replies
- 14.3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·