Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Jig & Fixtures

Build jigs and fixtures for safer, more repeatable cuts. Share table saw sleds, router templates, drill guides, and custom workholding setups.

  1. Started by collinb,

    My solution to cutting a semi-circle. Probably been done a million times before. semicircle.pdf

  2. Started by collinb,

    My door handle drilling jig. Mounts on the drill press. Adjusts to the desired 1/2" increments from bottom and infinite position from side. Markings at 1/4" points added to base for simplicity for setting side inset spacing. Just add the block desired for the handle screw spacing. Ok, I reinvented the wheel again. But that's what software people do. We see code and re-write it. We see things and reinvent them. It's a trait of the field.

      • Like
    • 1 reply
    • 3.4k views
  3. Started by Coop,

    Has anyone made a jig for their band saw to cut small logs into boards? I bought one a couple of years ago from some company in Canada that was doing a presentation at a woodworking show and it is a piece of crap. Their theory was good but the design and construction was bad. I'm thinking of maybe 10" - 12" dia. logs, 2'-3' long.

      • Like
    • 10 replies
    • 5.5k views
  4. Started by collinb,

    My first quick-and-dirty attempt was deemed scary by someone. This one is better. Covers a 2 ft distance. The little tab at the back is 1/4 inch thick, enough to push the piece securely. On the front is where I put a block that determines the bevel thickness and distance (which sets the angle of the taper). Though far from perfect it is far better than my first one. I even added a little handle on the back.

    • 9 replies
    • 4.8k views
  5. Started by bushwacked,

    So in my reading ... Got some books to help me cause I need it haha ... I came across this: Is this more of a situational crosscut sled? He's got some wide wood on there. This would be a lot easier to store and move if this is functional for everyday crosscut sled use.

  6. Hello. I was wondering if anybody had a idea on how to make dentle molding. I have just recently finiched my Jugent home and are going to install a 3 piece crownmolding on the wall/ceeling. But I need a lot of dentile mouling at least 120-150 ft. So it will bee a major pain to make all those teeth. How can i do this so that it does't take all of 2015 I also have planes to make a paint pipe dipping system so that I can get quick paint inn all the teeth corners. But that is another matter. I would appriciate if anybody could give mee pointers. I have a fully equiped woodshop, with saws, routers etc. Best regards Norway. T.Robertsen

      • Like
    • 10 replies
    • 8.6k views
  7. Started by Fxguy,

    Can someone point me in the right direction to find some plans for a Fence that I can build and add to my bandsaw and drill press table? I seem to be able to find plenty of jigs and fences for my table saw and router table, but not much for the drill press or bandsaw in the way of fences. Also any help or advice on design for someone who is pretty new to woodworking ? I can build things from plans without many problems as well as troubleshoot a few things that may go wrong in the process, but I would love to be able to come up with my own plans / designs especially as it relates to jigs and fixtures. I know most are born out of necessity but I'm hoping there might be…

  8. Started by Tom Crawford,

    Paul-Marcel has posted a short video overview that is worth watching if you are not familiar with them. http://www.halfinchshy.com Not something I've put on my "get one soon" list but certainly would be helpful if you make pieces with tapers, curves and/or sculpting.

  9. Started by Bill Tarbell,

    Thus far i've only created two jigs for the table saw. Both of them have runners in the bottom. I discovered i'm a bit fearful that storing them on a shelf would cause them to warp a little bit and throw off their accuracy. Due to this, i've found that at the end of a shop day i'll put the jigs back on the table saw so that they're in the slots and resting flat on the top of the saw. The bottoms of each of my jigs are made of MDF with the runner dado'd in. I just picture them warping like one of those cheap particular board entertainment centers tend to do after a couple years. Is my concern worthwhile or should i just breakdown and store them on a shelf? What d…

    • 5 replies
    • 3.9k views
  10. Started by Bill Tarbell,

    My wife asked for a little shelf to place in her spice cabinet so she could have 2 tiers near the back. It was a simple little project, but i figured it'd also be an excuse to practice splined miter joints... and this required constructing a spline jig I had a bit of 5/8 oak plywood from helping a friend make some bookshelves so i used that to make the upper portion. For the base i used some mdf i got from a used construction materials store. The runner was from a mahogany railing post i picked up from the same store. I started off by making the two top pieces with a 45° miter on one end. I then made 8 wedges at 45°. THe wedges were just roughly sized for …

      • Like
    • 8 replies
    • 4.9k views
  11. Started by woodbutcher74,

    Last spring I was working on a small box for a gift . I decided to add splines to the mitered corners and built a spline jig. Well some other things came up and it got hot so I never got back to that project until today. Built the lid and everything was going good so I decided to go ahead and cut the splines. Lined it all up and ran the first corner through and BOOM. Sparks and carbide flying all over the place. When I built the jig I had screwed the angled supports to the backer board and had all intentions of removing them after the glue dried. Never leave something like this half done!!! Since I didn't have a rip blade to cut a flat bottom for the spline slot I was usi…

    • 8 replies
    • 4.2k views
  12. Started by wtnhighlander,

    I had a nice one today. Spent nearly 4 hours constructing a miter sled with tall front and back fences. The intention was to get super accurate and repeatable cuts for inside and outside miters on 4 1/2" crown moulding for my kitchen cabinet facelift. Imagine the forehead slap I gave myself when I discovered that a 10" saw blade is about 3/16" too small to reach through the 1/2" sled base and the moulding! I can get by with handsawing the last bit and trimming it with a block plane, but man, that sure is an aggrivation!

      • Like
    • 9 replies
    • 4.5k views
  13. Started by lavenderallen89,

    I'm new to woodworking, Ive spent much time in the recent past looking up all kinds of wood working videos, and recently got my first table saw. And maybe this is a silly question, but I was starting to make my own push stick. I had a thought, I never saw any videos about adding sandpaper to the bottom of the push stick. To me it seems like it could give you more control over the stock. However, I am new so I figured I'd bring the question to the forums. Is this a bad or good idea and why or why not?

      • Like
    • 14 replies
    • 4.8k views
  14. Started by StrangeRANGER,

    Does anyone use the iPhone and Siri to to assist in their projects?

      • Like
    • 14 replies
    • 4.5k views
  15. Started by Bombarde16,

    Not an original idea, but I just wanted to share that I finally tried a trick that I had read about. To sand a cove cut, first create a custom sanding block. 1. Start with an off cut from the cove in question. 2. Spray mount sandpaper on to said offcut. 3. Use the offcut to shape a chunk of rigid foam insulation. 4. Once the foam is a perfect negative of the cove, mount sandpaper on it and use it to finish your piece. Not perfect, but it did cut down on to amount of finger busting hand sanding Sent from my iPhone using Tapatalk

  16. Started by dwacker,

    I was watching a you tube video and it was almost painful to watch. The guy was putting together a lower box. The rabbeted back and bottom fell a few times and he struggled to get it all squared up while attempting to clamp. I thought I'd post this little FREE trick for clamp less always square box assembly. Throw a couple on your bench or the floor, set a couple on top. Make them full size out of mdf for your drawer boxes and they square up themselves. Stack your boxes as high as you want. The uses are endless and sure beats needing a third arm.

      • Like
    • 21 replies
    • 9.7k views
  17. Does anyone have any cute techniques to quickly move toggle clamps between jigs? I bought some Bessey auto-adjust clamps, and they are pricey enough that I'd prefer to move them around than buy lots of them. Obviously for jigs with T-track I could just put them on a carrier, but what about jigs where they are in a fixed position? Obviously this isn't a very profound problem, but since I was thinking about it I thought I'd ask if anyone has thought of any ingenious solution. (Kreg sells an attachment plate, but it's not that much cheaper than the clamp!). Cheers, Brian

      • Like
    • 21 replies
    • 7.8k views
  18. Started by Nick2cd,

    I made these adjustable bench hooks so that I had a stop for hand planing and card scraping. I can put them side-by-side and support very long pieces if necessary. I'm finding all kinds of uses for them. They make great stops while I'm using my domino as well.

      • Like
    • 12 replies
    • 4.4k views
  19. Started by Nestor,

    Built this jig recently to help me with a tool cabinet I've been building. Got the plans from an issue of Shop Notes. The quick clamp feature makes it a snap to set up. Sent from my iPhone using Tapatalk

    • 8 replies
    • 10.1k views
  20. Started by Ronnie Boyett,

    I am new at woodworking and am going to make a cross-cut sled. What is best for the sled, plywood or MDF? Also, what type o plywood and is 1/2 or 3/4 best?

      • Like
    • 8 replies
    • 6.5k views
  21. Started by wdwerker,

    It breaks down and hangs on the wall when not in use. 3 sections 24" wide OD , 3/4" dowels 22 3/4" exposed x 5 inches clear between . 36" x 48" footprint x 76" tall The dowels started getting loose after many years of use, so I re-glued them and added a screw to tighten things up a bit. The top spreader knotches got loose ofer the years so I nailed and glued on some plywood to keep it from wobbling . The caster bases had similar issues and fixes. TripleH posted a comment so I took the pictures and thought some of you might want to make something along these lines. Word to the wise, eyeball all the dowels for straightness or just use some scrap 1 x 2…

      • Like
    • 7 replies
    • 4.5k views
  22. Started by the dude,

    I just got a new WoodRat 900 after having and using the WoodRat 600 for a few years I just got a new 900 I love the tool it is a very versitile tool and has made so many joints a king. Have any of you guys used a WoodRat ? Well if you Havent seen the Rat you have got to look at this video http://youtu.be/JkyKUBPO0to

    • 2 replies
    • 4.8k views
  23. Started by David Monette,

    Well, after watching Marc's video on cross cut sled construction, I decided to take the plunge and build my own. Turned out pretty good. Seems to be accurate - yes Marc, I used the 5 cut method. My table saw is a Grizzly G0715P 10" cabinet saw. Comments welcome...

      • Like
    • 12 replies
    • 5.6k views
  24. Started by ..Kev,

    Tenon jig As some of you know, I recently upgraded my table saw and then upgraded the fence on that. That means that none of the old table saw jigs would work with the new fence.. Here's the first one replaced.. The scrap Sapele is a little overkill but, better than burning I suppose..

      • Like
    • 16 replies
    • 4.5k views
  25. Started by Dnorris1369,

    Hey guys. Trying to decide on crosscut sled for a dewalt Jobsite table saw. I've been looking at the incra and one from rockler. Any opinions on either of these two? Also pros and cons for each vs building one Sent from my iPhone using Tapatalk

      • Like
    • 42 replies
    • 11.7k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.