Jig & Fixtures
Build jigs and fixtures for safer, more repeatable cuts. Share table saw sleds, router templates, drill guides, and custom workholding setups.
489 topics in this forum
-
If you don't use Baltic Birch enough to have scraps laying around to make jigs out of, Woodcraft has small pieces on sale for a couple of bucks. Shipping shouldn't be too bad. They also have 3/4" for 3.99. http://www.woodcraft.com/product/2004113/7914/baltic-birch-plywood-12-mm12-x-12-x-12.aspx#ProdInformationTab
-
- 1 reply
- 3.1k views
-
-
If anyone with a brain for jig making can toss me an idea or two, I would really appreciate it. I'm trying to turn a form, and then cut that form into two equal halves. I assume I need to run it through the band saw, as the TS won't have enough depth. My best guess to this point was to create a cone shape void (could be done segmented) and mount that to a base. that runs along the band saw track and doesn't cut all of the way through. Any ideas would be greatly appreciated just to give me a leaping off point, it nothing else. Thanks
-
-
- 6 replies
- 3.3k views
-
-
In working on an 86' trestle bridge we ran across a lot of boring through timbers and multiple stacked beams, some 5 deep 4x material. I developed jigs basically using standard 3/4" and 1" steel pipe nipples. Using pvc pipe and fittings, I fitted both ends with smaller diameters for boring 3/8", 1/2", and 3/4" holes. I took cheap pvc fittings from Home Depot and bored them and turned the outside diameter to fit. Then I drove one in each end. To attach to my jigs I either used pipe flanges or welded them in a custom jig. Attached are pictures of two of those jigs in use. The one shown above was made with a 3x3 angle, welding the pipes in place. Notice th…
-
- 3 replies
- 4.6k views
-
-
Thanks to Marc's excellent instruction, built a great jig for flattening a 50" x 12' slab. Looking forward to using it on many projects!
-
-
- 5 replies
- 4.3k views
-
-
I am all ways being ask how I make that 3-D pattern. So I made a video showing how I do it Tell me what you think http://www.youtube.com/watch?v=bP003llGw_w
-
- 1 reply
- 3.4k views
-
-
Bandsaw Walking Stick Hi everyone Just thought I would contribute to this new section of the forum by showing one of the jigs that I use quite a bit in my shop. LOML wanted me to make her a new walking stick. Had to be a minimum of 44” long but my lathe can only take stock 40” plus she wanted it made from a couple of different woods and it had to taper from 1 1/4”- 1”. I went ahead and made a new jig for making round blanks using my bandsaw. The jig had to be capable of holding the blank securely on the centers but at the same time allowing the blank to be rotated as it was passed through the saw. It also had to be attached to the fence of the saw to provide accurate…
-
- 5 replies
- 7.7k views
-
-
Hi. I'm currently living in Argentina, where materials aren't as readily available as in the States. I notice that most videos showing construction of shop jigs recommend 1/2 inch plywood. It is easier in Argentina to get 1/2 inch (or thicker) MDF. You guys think it is OK to use MDF rather than plywood for jigs? Is 1/2 inch MDF sufficient thickness for, say, a table saw sled? Thanks.
-
-
- 19 replies
- 30.9k views
-
-
I thought a while back during a WoodTalk that Marc mentioned a commercially Finger Joint Jig and he highly recommend it. However, I have not been able to find that anywhere. Does anyone know of which one it was? Thanks, Michael
-
- 4 replies
- 4k views
-
-
I was re-watching some of Marc's vids this morning and came across the exact width dado jig. i was wondering if there is a good reason this won't work with a top bearing pattern bit (flush trim). this would eliminate the need to set up the brass bushing in the router (please note, I'm very lazy and more importantly, i don't yet own a set of brass bushings). the only hang up i can foresee is if you wanted to make a dado that is less than 1/4" deep, you'd either need to thicken the frame of the jig or use a shorter pattern bit (based on a 1" cutting length pattern bit). what are your thoughts?
-
- 3 replies
- 4.5k views
-
-
I just picked up an older liegh 24 inch dovetail jig. Liegh. D-1258R-24. Do I need special bits and collars to use this jig? Can I use the ones from my porter cable 4212 jig? I mostly do through dovetails.
-
- 1 reply
- 3.2k views
-
-
Hi everybody. I know there are heaps of shelf pin jigs on the market. I researched as many as I could and ended up with the one Kreg makes. I thought it might be fun to make a video on how easy it is to use. Have a look at it if you have 5 minutes to spare and have been pondering getting a shelf pin jig. I also show how the 5mm and 1/4" drill bits work in the same jig. http://www.youtube.com/watch?v=JX4rJkQMC-Y&feature=youtu.be
-
- 5 replies
- 3.8k views
-
-
Good Morning, I need some help with setting up a router jig to cut a curve for a table top. The curve is very subtle, but needs to be exact on all the boards, so I am planning to use a "Compass" type jig on my router to cut the template, and then just flush trim bits with a guide to cut all the pieces. Unfortunately my geometry is failing me at the moment, and has for a few days. So I am hoping someone can give me a quick refresher course here on how to calculate the length of the arm (radius) that I need on my compass jig to get this arc. The table top spans 22" long, and the boards all deflect (not sure that's the right word) 1/4", and are symmetric…
-
-
- 18 replies
- 7.6k views
-
-
I was playing with the idea of making a jig with an indication dial, but came across this cool idea. What do you think? http://www.finewoodworking.com/workshop/video/jointer-knife-setting-jig.aspx
-
-
- 5 replies
- 7.2k views
-
-
Making up a tenoning jig today. I kept needing my combination square for other things. The rafter square's kinda handy for somethings, but mostly sits on a shelf. Until today when I was having trouble getting this jig square whilst the glue dries.
-
-
- 4 replies
- 3.9k views
-
-
Here is my new shooting board. I've never had one before... So I made one based on an article in Fine Woodworking magazine. I used 3/4 MDF.
-
- 7 replies
- 4.7k views
-
-
Saw this on lumberjocks yesterday thought it looked intersting so I made one last night it worked great the first one came out sorta rough so I fed the second one a lttle slower through the hole it came out a lot smoother. is not my video it was on lumberjocks I'm just shareing.
-
- 2 replies
- 4k views
-
-
I ran across showing how to make a marble track toy set. He uses a bunch of neat jigs.
-
-
- 2 replies
- 3.7k views
-
-
Hello All, I've never used a dovetail bit in my router table before, so before I go out and buy one, I want to check to see if this will work. I've used this jig (see below) with great success with a straight bit for cutting box joints on my router table.... If I simply replace the straight bit with a dovetail bit, will it make dovetails? Or do I need to adjust the jig for some reason that I am missing? The jig: Thanks! - EG
-
- 5 replies
- 3k views
-
-
The mother-in-law is asking what I want in my stocking this year, and a tenoning jig has been on my list for a while and is about the right price for the gift she'll get me. I know most of them are similar to identical. I was checking out the Delta online and it kinda "looks" nicer than some of the others, but it gets a lot of bad reviews. Can you guys recommend from experience a few brands to go after or stay away from? Any features that one has and not another, fit and finish, etc. Not interested in building this jig, and need to stay in the $100 ballpark. Thanks fellas!
-
-
- 18 replies
- 7.5k views
-
-
I purchased a pin router 2 weeks ago the first project to familiarize myself with the operation was a zci for my dedicated dado ts. I surprised myself the process was straight forward and very simple got it on the first attempt.
-
- 1 reply
- 3.3k views
-
-
Hello all. I will post an intro in the proper section but I just answered the thread where a member was injured on a bandsaw for lack of a push device. I have been in Aerospace for over 30 years and I have never heard of anyone hurt on a bandsaw while using one of these. This one is shop built and there is no reason it could not be made from wood, perhaps 1" plywood or MDF? Sometimes there are notches cut on the inside of the "V" for work that is smaller but nearly all the time just the V works well. As to pinching the blade, just ease up on the work pressure and let the saw do the work if that happens.
-
- 13 replies
- 10.9k views
-
-
I've just finished my first exact width dado jig (EWDJ), and I really like it. Quick to setup and easy to position, exact width dados (almost*) every time. I think next time though I'll use some angled aluminum for the fence - straighter than anything I can cut at the moment. My only problem with it over using my dado stacking set is the amount of dust it chucks around. The regular dust extraction does almost nothing to stop it throwing dust everywhere, but mostly down the dado I just cut. Has anyone figured out a way to collect most/all of the dust this process generates. I was thinking some kind of router base plate, with a 2 1/2" port mounted pointing straight …
-
-
- 6 replies
- 3.5k views
-
-
Got it at a flea market for $5. A router attaches to the stainless plate and slides up and down. There is also a guide/holder? at the bottom. It's a mystery to me.
-
- 6 replies
- 4.2k views
-
-
Ok not a shop made jig but works perfectly with my lift. Now to add a dro and lift motor. Drop spacers in track to limit mortice width. End grain only limit is ceiling height.
-
- 1 reply
- 3.2k views
-
-
This here is my stripped down....no frills tenon jig made from scrap wood. It gets the job done....and maybe I'm just not used to it, or not used to the process, or something...but I don't like using it. I need to push with more force to get the wood through the blade...but I figured that it was due to a few factors: height of the cut was 2 3/4" and the wood was QS White Oak. Even so....It felt uncomfortable. I cut 6 tenon cheeks and everything went without a hitch and I'm happy with the results, but I think this jig could be upgraded. I'm on the hunt for some new ideas.
-
-
- 14 replies
- 4.5k views
-
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·