Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Jig & Fixtures

Build jigs and fixtures for safer, more repeatable cuts. Share table saw sleds, router templates, drill guides, and custom workholding setups.

  1. Started by farmbag72,

    I recently purchased a PC 4216 dovetail jig and have had great success cutting with the dovetail bit, straight bit and my spiral upcut bit (for box joints) in solid wood. I can not for the life of me, get clean cuts in Baltic birch ply (3/4" & 1/2") with any of the jig bits. I've tried slower bit speed, moving the router quicker & slower, pushing down firmer, trying to "float" the router on the template. Nothing works. The tear out is all on the side facing me. The back sides come out perfect because of the backer boards in the jig. I've watched tons of vids on using this jig & don't see that I am doing anything differently from the vids. Anyone else ha…

      • Like
    • 21 replies
    • 10.7k views
  2. Has anyone ever made a hinge for the Dewalt track saw track ? I would like to cut panels the way you can with a festool using the hinged track and MFT. I do not want to buy another tracksaw just for this capability but I did not see a way to adapt the festtool hinge to a dewalt track. Any suggestions ? Regards, Bob.

    • 2 replies
    • 7.1k views
  3. Started by Andrew Pritchard,

    Having spent some time this weekend trying to hold the hose for my shop vac whilst I'm sanding with my spindle sander on my drill press, I could really have done with one of these:

  4. Started by rmac,

    This is a jig for cutting through dovetails on the bandsaw. It uses a sliding fence arrangement instead of the spacers used with similar jigs that have been described by Lonnie Bird, David Marks, and others. Check my blog for more information and detailed drawings for building you own. -- Russ

    • 2 replies
    • 8k views
  5. Started by Janello,

    I have no experience with this and I'm looking for some advise. I see there is a large spectrum of options from a $300. blum jig to an $11. template used with a 35mm forstner bit. The problem I see with the cheaper store bought jigs is depth of holes being hard to keep accurate. I'm thinking a hand made mdf template/jig to use with a router and bushing guide would be the cheapest and most effective way. I could incorporate a depth gauge for the bit right on the template. Does this sound like a good idea? If so where can i find the hinge hole locations/dimensions for setting this jig up? If buying one is the better option, what ones have you folks used and sugg…

    • 11 replies
    • 6.5k views
  6. Started by robjeffking,

    I really like this new add-on I made for my planer. I've added quite a few new tools to the shop this summer and Ive had to get creative making all the tools share space. I noticed that my work table and planer were almost even with each other. Now I can put the planer right behind my work bench stack the board in my guide jig. The sides of the jig helps long boards track straight through the planer and catch the exit roller stand.

  7. Started by otis,

    I'm looking to get some new bits for my dovetail jig and was thinking of replacing my straight bit with a down cut spiral bit. I'm thinking it would give me a cleaner cut with less chance of tear out. Has anyone tried that? Is there any reason that wouldn't work?

      • Like
    • 9 replies
    • 6.7k views
  8. Started by JoshC1501,

    Has anyone ever built one of these? Any reason you see why it wouldn't work? I got my tablesaw sold, going to be without one for about a month. Thinking this might be a good time to really get my money worth out of my bandsaw. I have a regular mitre guage that I use sometimes, but it pretty easy to get bad cuts using it.

      • Like
    • 6 replies
    • 5.2k views
  9. Started by Karbonfiber,

    Hi Guys first post so bare with me and if its in the wrong section I apologize. So I set out to pick me up a cyclone for my dust collection system as it is a nice to have easier clean out and such. Well I didn't look much further than you tube and decided this was something I could build. Went to the home depot and picked up the garbage can and PVC fittings and slapped her together in an hour max. Check it out I had to share as it works great and on cost around $50.00 I am definitely going to scale it down to a 5 gallon pail for the shop vac more portable with the miter saw. Hope it inspires anyone looking for a way to reduce plugged up vacs.

  10. Started by Tom King,

    I bought a used Leigh jig a while back, and was getting it set up today. It didn't take long to see there would be a lot of time wasted switching bits, and making test cuts, so I came up with a much easier way. System: Two routers. One with a straight bit, and one with the dovetail bit. I didn't have but one of the Leigh adjustable bushings, but a 3/8" bushing with a 1/4" shank spiral 1/4" straight cutter looked like it was close enough. I only had the one 8mm collet reducer that came with the kit, so I used that with the included dovetail bit. It worked fine with the other bushing and bit. Now with two routers, each with bits that would work without swappi…

  11. Started by krtwood,

    A quickly cobbled together jig to put tenons on the end of some 3/16" dowels using the table saw. The jig has two different positions to put a second tenon on a short length so I could still turn it without getting near the blade. I do have a lathe, but I thought this was an easier way to get repeatable results. I needed 8 of these for a set of dollhouse size chairs. And a short video of it in action: http://www.youtube.com/watch?v=t-kplGrgbtw How would you do it?

    • 8 replies
    • 5.1k views
  12. Started by JoshC1501,

    I am building some really nice cornhole boards for myself and friends. I wanted the the plywood top to sit flush with the maple frame, so the edges of the plywood are not exposed. On my first trial out of pine, I was having a hard time getting consistent stops clamped to ensure that the rabbeting bit didn't go clear through the end of the work piece. I made two of these, one for each end of the board. Attaches to the t-track that I integrated into my workbench. The stop block could be made bigger if the stop was further from the end of the work piece, but this will get me about 2.5" from the end piece. Using it for the first time today, seems to work well.…

      • Like
    • 5 replies
    • 3.9k views
  13. Started by amateurexpert,

    I am new to woodworking and new to the forum. Recently purchased my first home and am starting to do some projects in my garage. On my latest project I ran into an issue that I am wanting to get some advice on. I am needing to cut 25 half moon shaped arcs out of 2 x 8 lumber. The half moons will be 20" long so the actual curved cut it about 30" long. I have a scroll saw that I have attempted to use, but the scroll saw is too underpowered to make that long of a cut on 2 x 8 material and do it 25 times. I have done some reading online and have come to the conclusion that a bench top bandsaw might be the best way to go. Does this seem accurate? If so are there any suggest…

      • Like
    • 8 replies
    • 11.4k views
  14. Started by CJC5151,

    Hey guys...for the past few years I get a booth at a local art show and sell end grain cutting board's. I sell out every year so it's been great. The question is they are a pita to clamp up and take forever when u are building them in bulk...any ideas on a clamping fixture to help speed up the process. Thanks

      • Like
    • 9 replies
    • 4.7k views
  15. Started by rodger.,

    I was gluing up a panel last light, about 22 inches wide. I decided that I better use some cauls, as the panel was decently wide and I didn't want to have to work more than I had to flatten it after the glue up. So I grab 2 sets of my shop made cauls, which have tuck tape on one face. I clamped up the cauls and then I finished by clamping the two 11 inch workpieces together. Off I went to have a cold beer - I was done for the night. Today I go into the shop and loosen the cauls. The first set drops off no problem with a clunk. I go to the second set and the bottom caul is stuck. No big deal I think, it's prob just a bit of glue squeeze out between the panel and …

      • Like
    • 10 replies
    • 4.7k views
  16. Started by wtnhighlander,

    Greetings and happy holidays to all! Do any of you have experience using polyurethane glue ( gorilla glue ) in a bent wood lamination? I'm planning a round table that will require bent aprons. Several anecdotes I have read indicate PVA glue does not cure hard enough to prevent tension in the wood from slowly pulling the layers apart. Epoxy has been recommended, but I can obtain the necessary volume of poly glue much easier. Any thoughts?

      • Like
    • 11 replies
    • 8.1k views
  17. As my heading states, I'm looking for any ideas / solutions for edge jointing 8' x 12" x 1 3/4" thick. Problem is I don't have a jointer that could handle this as I only have a sm. bench jointer, and no funds nor space in my shop for a full sized jointer, I plan on glueing up 2 boards to make 24" width. The lumber is rough sawn, I've planed both faces, I've had the idea of either making a po' mans track saw or make some sort of jig for my table saw to true up 1 edge. But that's all the ideas I have. Any thoughts, suggestions, ideas to any or all of you on this forum, thanks in advance for sharing. -Robert

      • Like
    • 10 replies
    • 4k views
  18. Started by Bombarde16,

    Ever get the setup perfect on the first try? Me neither. But Norm nailed it in this week's free episode! I know, I know...he's got a production staff to set up the tools and edit out all the test cuts it took. It was still cool to watch someone walk up to a router jig cold and go straight to the actual work piece.

      • Like
    • 15 replies
    • 6.1k views
  19. Started by mds2,

    If you have the 2013 issue of Tools and Shops from FWW you have probably seen the article on L fences. I had never seen one before but the article showed a lot of practical uses. I built one tonight. Really couldn't be simpler and took all of two minutes. Does anyone here use one? http://i.imgur.com/yx6HcJP.jpg

  20. Started by WelshWood,

    Hey guys, I'm in the process of making a new workbench for my workshop. I almost justified buying the MFT/3, but for the price I could build a better bench suited for me. However, I was wondering if Festool sell the pivot they use on the MFT separately? Would be great to have that on my own workbench. Apologies for being rather vague on this Thanks in advance, ~WW

    • 3 replies
    • 4.5k views
  21. Started by chopnhack,

    Yes I know you can buy them at every woodworking store, yada yada.. I made one from scraps that cost me nothing, cleaned my garage of some spare plywood that would probably never get used and gave me a functioning jig in a custom size. All without spending anytime tooling around town or wasting gas. There, call me cheap This particular jig is perfectly sized to drill the side walls of the cabinets for shelf pins in one set up per row. It is self aligning at the side of the cabinet. Line up the top edge, two quick clamps, drill, rinse and repeat. It is two 3/4" pieces of ply laminated together with some glue, clamped and left to dry, trimmed on t.s. Third piec…

    • 2 replies
    • 3.5k views
  22. Hello everyone. i dont know the name of these jigs, i know they are sold for 50-60$ but im sure i can make one easily with scraps. i dont know the name either. Its a small frame on which you put your big 20l of lacquer or thinner that tilt just so its easier to pour and so you dont spill half of it on the floor. anyone has a place where i could browse for a model to copy in wood ? or maybe someone made one already and has some tips ! thanks !

      • Like
    • 8 replies
    • 4.2k views
  23. Started by ReLMAustin,

    Hi, I recently got access to a Shopbot through a Tech Shop opening close to Austin. The first project I thought to use it for is cutting a zero clearance insert for my table saw. I have this table saw from Porter Cable. The insert that came with it is thin stamped metal. The lip that holds the insert isn't deep enough to use 1/4" plywood like I see a lot of people use for inserts. So I designed a cut model that makes most of the insert 1/2" but puts a ~0.15" lip around the outside where the supports are. It also provides areas for all the structure under the insert, a pocket where the blade comes through, and openings for the adjustment screws. You can see…

      • Like
    • 5 replies
    • 5.8k views
  24. Started by dwacker,

    I started building my left side saw support this weekend. I though some folks here might like to have one or use it for inspiration for your own designs. No modifications to the saw except a hole in the plastic rail cap. You can see my progress at my blog. The steel rod is 1" hot rolled. I'll pick up the rest of the steel this week and finish it up. The block is held by the switch bolts acting as set screws. Rod is 50" long so supported about 24" inside the tube when extended 25". http://www.pnwwoodworker.com

    • 7 replies
    • 4.4k views
  25. Started by Bombarde16,

    Here's my take on the bowl scooping jig from David Marks's sculpted bowl table. Mr. Marks used a router whereas I did mine with a circular saw. The overall concept, however, is the same. The tool is mounted on a circle sized to spin nicely within a circular opening. By plunging the saw a smidge at a time, you can rotate through 360 degrees. (Hey look, a circular saw going in a circle!) Plunge a smidge more, spin...Plunge a smidge more, spin... I used a circular saw first and foremost because it's a simpler jig to build. Simply tack some scraps onto the base and clamp whereas the router needs to be cradled within a set of curved rails. Moreover, the circular sa…

    • 3 replies
    • 4.8k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.