Jig & Fixtures
Build jigs and fixtures for safer, more repeatable cuts. Share table saw sleds, router templates, drill guides, and custom workholding setups.
489 topics in this forum
-
Anyone here use one of these? I got this at an auction a few years ago and will finally be putting it to use this summer as the garage indoor shop begins to take shape. Sent from my MotoE2(4G-LTE) using Tapatalk
-
- 6 replies
- 4.4k views
-
-
PIcked up one of these yesterday at a bargain price. The price was low enough that I think getting the fence justified it. Of course 1/2" is apparently limiting. Should I ever use it as a shaper the motor should be upgraded and sleeves put on the spindle to accommodate better cutters. Some have commented (other sites) on the large work surface provided. Seems to be a well-engineered unit for the hobbyist. Since it is considered to be an under-powered unit my first thought is to take off that nice adjustable fence, build a base for it, and so make it mountable on my router table. (Of course I would not completely cannibalize it, especially now with metal prices so…
-
- 4 replies
- 4.4k views
-
-
I repurposed my old Craftsman Drill Press with a dedicated tilt top table. This is my first drill press purchased new in the mid 80's and has served me well over the years. I replaced it with a Powermatic PM2800 about 8 years ago but must admit the Craftsman is a quieter and smoother but that's another story. Now the Craftsman is back in service. The Tilt Table is a blend of many ideas so thank you to all those woodworkers posting excellent content these days. The manufactured table top came from Peachtree (older model) and the fence is repurposed from the PM2800. Here are a few pictures.
-
-
- 5 replies
- 5.7k views
-
-
Rob Lowrie created pyRouterJig, a really powerful application for making custom templates for the Incra LS positioner. I wrote this tutorial to show how to use it. Custom Box Joints using the Incra LS SystemBelow you will find a picture of a box made with a custom template. All the box joint fingers are the same size. The tutorial explains how to do that.
-
- 4 replies
- 6.2k views
-
-
I needed to make a whole bunch of lap joints for a project, and I wanted them all to be perfect. I had heard of a "kerfmaker" but never used one. I did a little searching around and came up with this idea. It is based off of a different jig I found online but I simplified it further. The way it works is you take a piece of wood and screw a screw into one end. You adjust the screw to stick out the same thickness as your table saw blade. Turn the screw "in" makes a looser joint, adjusting the screw "out" makes a tighter joint. It takes a little trial and error to get it correct, but once it is dialed in you dont need to do any adjustments. Here are a couple sho…
-
-
- 2 replies
- 3.9k views
-
-
I was reading some posts that had a ford/chevy tone comparing the Dowelmax and Domino tools. Several guys accused the Dowelmax of not being accurate. I found this surprising since it is self clamping, where the Domino is not. The Domino may cut tenons on complex angles (I really don't know), but for plain vanilla joints, the Dowelmax looks like a great tool for the money. Am I missing something? Thanks
-
-
- 45 replies
- 16k views
-
-
PLEASE CAN SOMEONE HELP IDENTIFY THIS PART. ANY HELP IS MUCH APPRECIATED
-
-
- 18 replies
- 4.8k views
-
-
Not sure if anyone has thought of this but I'll throw it out there and maybe it will help someone. Was trying to Sq up the fence on a cross cut sled I'm building. Got my pivot screw in and every time I try to back the sled off the saw enough to get a screw in the fence moves a hair. Pesky clamps won't work because sled is on saw top. I drilled a hole on the edge of the base of the sled and used one of my auxiliary fence attachment clamps. Works perfectly. Now can clamp down the fence while on the saw top.
-
- 2 replies
- 3.3k views
-
-
I've found a jointer alternative, Actually two alternatives. Of course these alternatives are still jointers, functionally that is, though the tool might not be identified as such. (For those who enjoy philosophy: same description, different referent.) On the one hand have this 1/2" OD, 1/2" mount router bit, much like the one shown. If I place it properly aligned with the fence then I can manage the short sides of a piece. (Which is all I see myself needing to do for long, long time.) Then I have to add a shim of some sort to the output side for a smooth transition. Shouldn't be hard. The second alternative involves getting this: http://mansfield.craigsli…
-
-
- 50 replies
- 13.1k views
-
-
I started drilling holes for clamps as Mark did, but realized I don't have the number of clamps of that style required, nor the budget to get them. But I have enough parallel clamps to do the trick. However, that type of clamp would have had a rough time with the curve of the arm, so I cut notches in the bottom of the form so that the clamps would have a place to grip. More than one way to skin a cat I guess.
-
-
- 8 replies
- 4.7k views
-
-
I attempted my first TS Cross-Cut sled last night and the results didn't quite pan out like I was hoping. I got the sled lined up perpendicular to the blade great and it slides in the tracks on the TS like butter. But then I went to put the sled over the blade, while lowered, and clamped it down hoping to turn the blade on and raise it up through the sled. The sled is made of 3/4 ply and as I was raising the blade on the TS it simply wasn't cutting through the ply. It was bowing in the middle from the pressure of the blade so I ceased for safety concerns. It cut shallowly but really didn't cut deep. As an alternative, I ran the blade shallowly creating the recess fo…
-
-
- 14 replies
- 4.4k views
- 1 follower
-
-
Made from scraps. 3/4" birch ply, 3/4" plywood, shop fox t slots, MDF fence, Incra T-bolts and knobs. And dado for hardboard replaceable inserts.
-
- 5 replies
- 4.5k views
-
-
I've been using threaded inserts a lot on my woodworking jigs, mostly EZ inserts but also t-nuts on occasions. The sizes I use the most are 1/4", 5/16" and 3/8". Now earlier today, I was reading the "Complete Vise Instructions" manual for the Benchcrafted Classic Leg Vise (available from this page) and at page 12 I found this: The holding power of machine screws in wood is about the same as using a threaded insert, and you don’t have to buy the inserts. It’s also a great technique for making jigs and knock-down joints. Thoughts? Is it really "about" the same? Should I stop buying threaded inserts and use taps to thread the holes instead?
-
-
- 9 replies
- 7.3k views
-
-
After watching a demo by a Canadian outfit with a small carriage attachment on a 14' bandsaw at the Baltimore wood show, I have been scratching my head. It seems their secret to straight sawing is to hold the work piece rigid, not allowing it to move. Their claim is that just released stress at, and past, the cut line, allows the work piece to push against the fence causing blade drift. It kind of makes sense.. But a grand for their log cutting jig set up for board re-saw seemed a bit rich for my shop. Maybe today while in the shop I'll try a re-saw with the fence withdrawn to a point where it ends a couple of inches before the blade. I woul…
-
-
- 14 replies
- 4.6k views
-
-
I had time to try the dovetail jig again today and I have to say I am getting somewhat frustrated. I seem to be unable to get the through dovetails deep enough. I am using my Festool 1400 and the jig. If I set the bit out too far it won't cut the wood and if I set it so it will cut the wood the resulting cut is not deep enough for the pins to match up. Any ideas on what the heck I am doing wrong. Also, the first dovetails which were too short were cut nicely, but later attempts are not as nice and look kind of jagged. If you have any ideas, I would love to hear them. Also, I would like to ask a couple of other questions. Are the Leigh jigs worth the added expense…
-
- 3 replies
- 3.2k views
-
-
My next project is going to be a 70" round dining table. I plan to use 6/4 stock and still deciding on species but figure Walnut or Cherry. I wanted to get advice from those who have done it on the best way both safety wise and finish product wise to cut such a large circle with my standard shop gear? The equipment I have is Grizzly 14" band saw, 10" Hybrid Cabinet Saw, and router. Getting an extra hand in the shop is possible but not easily done but assume it's going to be a one man operation. Thanks James
-
-
- 11 replies
- 5.5k views
-
-
As usual, I'm probably over thinking this. I want to make a small free standing shelf that will go in a closet to hold ammo. It will be 24x24x12 deep with three shelves and a 1/4" ply back. Sides and shelves will be 3/4" pecan. I know it's going in a closet, but I need the practice. I would like the shelves to rest in dadoes in the sides with part of the shelves to extend thru the sides as thru tenons either one larger one or two smaller ones. Plan of attack is to build a jig, practicing on scrap to correct size for the dadoes, using a plunge router to cut the stop dadoes. Then cut the dadoes approx. 1/4" deep. I can see using a wheel marking gauge to mark the top and b…
-
-
- 16 replies
- 4.3k views
-
-
Wife's family was up over the Christmas break. Took brother-in-law and father-in-law over to my local toy store one day. Had not seen the PM-TJ before. Almost fell in love at first sight. And then touching it. Smooth bearings, easy adjustments. What a nicely engineered piece!
-
-
- 37 replies
- 8.1k views
-
-
I have been looking at thi jig for the taper and straight line function. I have read that the tape measure will set off the saw stop. Does anyone have any alternative suggestions or experience with this jig.
-
-
- 3 replies
- 4.2k views
- 1 follower
-
-
Does a good job. The diameter of the disk is 7''. If someone is interested in this jig and need more details, ask here.
-
-
- 9 replies
- 7k views
- 1 follower
-
-
I've looked at a few instuctional videos and want to try a 'spline' jig. Looks easy enough, my concern is making the spline filler pieces. Straight splines seem to self expanatory, but I've seen dovetail spline slots and no mention of what you use to fill those joints. Anyone using/making spline joints?
-
-
- 11 replies
- 6k views
-
-
found a new guy on youtube and have been watching him. I have learned quite a bit of new techniques form him, but this jig seemed really nice if you need to flatten some veneer sides. the jig is about 7 minutes in ...
-
-
- 4 replies
- 3.5k views
-
-
Was at a local auction on Tuesday. There were some planes of interest. Unfortunately there was someone else there (apparently a collector) who wanted them more than I. Still, I ended up spending about $20 on a modern Sargent, roughly the same size as a #6. (I sold my #6 b/c I didn't want to spend the TLC hours it needed.) The point: Had a conversation with another bidder about his use of old planes. What he does when needed is get planes (I guess ones that are pretty beat up) for the tote. He takes off the tote and uses it as a handle on a jig. It's a cheap way to get a quality grip. Very often a plane with a good tote, but in rough shape, will sell for just a few…
-
- 1 reply
- 3.1k views
-
-
Making a small cutting board today, I needed a way to flatten it after final glue up. I have no drum sander, and this piece is too small for the planer, even if that wasn't a terrible idea. So, I came up with this inverted sort of router sled. I just cut some sacrificial strips just wide enough to glue on opposing sides of the board, so it could float between them. Then I ran it along the fence of my TS router table insert, over a flat end bit. Rotate 180*, make another pass. Move the fence about 1 bit width, rinse and repeat. Worked like a charm, much simpler than a sled for the router to ride in.
-
-
- 42 replies
- 14k views
- 2 followers
-
-
Looking to see if anyone lives in or near Dayton Ohio Sent from my iPhone using Tapatalk
-
- 13 replies
- 4.3k views
-
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·