Jig & Fixtures
489 topics in this forum
-
After using this thing for a year I had a no-brainer. Tell me what you think. https://youtu.be/8FmuEFcJJUw
-
- 1 reply
- 3.5k views
-
-
brusso hinges are nice, but are there more moderately priced quality hinge available.
-
-
- 15 replies
- 5.7k views
-
-
Not as much as I had hoped but the kitchen is essentially done before the chilly weather hits and I can't work outside. Finishing required I make a better tapering jig. You'll notice 2 holes on the left side. This allows me to move hold-downs for wider or narrower material. The miter sled is really, really close to perfect. The right/rear post was made adjustable. When I cut two corners on it they seem perfect with the try square. But when I do 4 in sequence there is a bit of an error on the 4th corner. it seems to be off by such a small degree, perhaps just an 8th of a degree. Perhaps I'll just give in and modify it to the complementary angle version. As close as…
-
- 2 replies
- 3.4k views
-
-
When i built my first guitar, radius blocks seemed ridiculously over priced, so I made a jig to make my own.
-
-
- 4 replies
- 4.5k views
-
-
https://www.kickstarter.com/projects/ninevolt/sukecchi-portable-multi-function-creative-sketch-t When it comes out, that is. and depending on price.
-
-
- 6 replies
- 3.8k views
-
-
Hi everyone, I'm a beginner seeking advice. I recently got a pocket hole jig and set it up. I am pretty sure I've done that correctly. Some of the videos suggested using a nickel to set the depth of the bit, and I've set the collar so that the drill stops just short of the base plate. I've been practicing and the holes themselves look pretty nice. However, the joints don't seem strong. Is it possible I'm not using long enough screws? Or do I just need to keep practicing? Thanks so much for any advice!
-
-
- 13 replies
- 4.8k views
-
-
I was watching this video on making a 45 degree miter sled. In the video he says that what matters is the 90 degrees of the two sides for your complementary cuts and their relationship to the blade is not so important. If that center angle is off then, once you mate the outside edges, the centers will not be in alignment. Do people take *basic* geometry any more? The comments reflect his error.
-
-
- 3 replies
- 3.6k views
-
-
Hi all, Im a home CNC hobbyist and woodworker. I do alot of glueups that involve many different layers of woods to put in the cnc. The outcome is to have different layers of wood present for the contrast in my projects. I have no good way of doing these glueups that is sustainable. Currently, I use clamps around the edges and calls down the center to try and achieve a bond in the center of the glueup. However, I was tinkering around sketchup and this idea has been in my head for a week or so. Question: Does this thing exist somewhere for purchase? or has anyone built a glueup press like this? Thanks, Chuck
-
- 9 replies
- 4.3k views
-
-
Finally got around to it. Perfect 90° cuts. I made it small for working with small pieces. May make a larger one later for larger pieces. T track coming soon. Sent from my MotoE2(4G-LTE) using Tapatalk
-
-
- 19 replies
- 5k views
-
-
Since I don't have a jointer, I do the (tedious) thing where I hot glue the workpiece to a sled with little shims underneath to fill the voids and "joint" (with a thickness planer) one surface. This works great for boards that are reasonably not flat - I just cut little 3 degree wedges off the end of a 1"x1" scrap piece to make the shims. The edge of those shims seems to be about 1/32". This means for boards that are *almost* flat, but just rock a little bit, the shims don't fit under the gaps. I've tried business cards and little folded pieces of paper, but those seem to compress a little bit when the feed roller presses down on them, defeating the purpose. I've heard th…
-
-
- 17 replies
- 6.3k views
-
-
Saw my instructor in cabinet class throw this together. Thought it was pretty smart and creative. Was doing it to recreate another piece for a repair job. http://images.tapatalk-cdn.com/15/08/25/8a60c5129bdde0316a7e1c381ff8deab.jpghttp://images.tapatalk-cdn.com/15/08/25/f2819e8467e0c9f28ca8e754705d36e4.jpg] Sent from my SCH-I545 using Tapatalk
-
- 7 replies
- 4.8k views
-
-
In this video I show some assembly supports (made with a little bling) that I made for my Workmate
-
- 3 replies
- 3.8k views
-
-
My new drawer rail jig. The only change I'm going to make to it is with a forstner to drill a number of access holes in it to allow mid-rail screws. This was built for 20" rails. I may cut it off or build a smaller one should I ever need to build a smaller cabinet. A couple of offset pocket screws and it's solid. Just squared it up with a framing square. Works well and a lot less and $30 or $40 for the plastic things.
-
- 3 replies
- 3.5k views
-
-
I happened to use this jig yesterday and thought that it might be of interest to others that make picture frames or small frames for other uses. I found the plans in a magazine several years ago and it has turned out to be a very handy thing for me over the years so, I'll pass it on. As you can see, it clamps all four corners at once using only one clamp and makes for easy, quick glue-up. . Hope this helps someone sometime. Rog
-
-
- 41 replies
- 19.4k views
-
-
So I had to purchase some 8/4 cedar from big box store due to time constraints (saw mill is hour drive.) Every single piece cupped and bowed. I cut them in half, as they are 2x8, and my benchtop jointer is 6 1/4" and squared them up. Everything looked good. Then I tried to glue them and every one of them were bowed. so yes each side was square, but when laid next to each other there would be a gap in the middle or at the ends. So, I think I'll make a jointing jig for the table saw, but I don't like the idea of some I've seen involving screwing into the wood to secure it. Anyone got one that doesn't involve this and can do long pieces? currently I'm doing 5 foot …
-
-
- 21 replies
- 5.1k views
-
-
This is my third sled in five months. If you'll remember my first posts here were about how to make a sled that didn't suck. Inevitably, I failed that time and the one after. But I think this one is doing pretty well. I borrowed heavily from many people online and I'd thank them but I don't remember their names. I find the stop block a great thing to have but don't really like having to clamp one on all the time. So I picked up a 4 foot Kreg Top Trak and installed that. I got a production stop and swing stop. I'm going to possibly tap the production stop and put a block of wood on the bottom so it reaches further down. The Kreg track is not made for a five inch …
-
-
- 18 replies
- 4.8k views
-
-
I got one of those MLCS thin stock jigs and it doesn't fit my saw. When it is adjusted all the way towards the blade it can only extend to about 5/16" from the blade. I got it to slice thin strips to use as inlay. My question is...what is the normal distance from your miter slot to your blade? I have a DeWalt job site saw so I'm wondering if the miter slot is a non-standard distance from the blade, thus causing my thin stock jig from getting close enough. On the left side of my blade my miter slot is 6" away. On the right it's 6 and just over 3/16".
-
-
- 10 replies
- 4.4k views
-
-
I was thinking of buying the universal magswitch featherboard but I can't tell if the switches are removable. It would be nice to take them out for a shop made jig. Does anyone have one of these featherboards with the feather part on both sides?
-
- 7 replies
- 5.7k views
-
-
I have been using Bessey's auto adjust toggle clamps for several years now and they work great ! I just saw an ad for Armor auto adjust toggle clamps from Rockler. They have several versions that work with a 3/4" or 20mm dog holes. Anyone have them or tried them in a store ? I would have thought the auto adjust toggle would have been patented. Only thing I could think of was Bessey just licencend it and the exclusive period might have expired.
-
- 2 replies
- 3.5k views
-
-
I have a sectional couch in my living room - made up of 4 sections and forming a large "L" shape. Each section connects with a connector similar to this (image found on Google)... My issue is that the corner and sidesections won't stay connected and are constantly drifting away from each other. The connectors seems to grab firmly but apparently not with enough force to keep the sections together when people geton/off the couch. The couch is in the middle area of the room so there are no nearby walls, etc. to hold or anchor the couch. Any suggestions for some sort of alternate connector that will firmly lock the sections together but still allow them to be discon…
-
-
- 7 replies
- 6.5k views
-
-
I use one of those old Craftsman universal jigs for tenons. To cut them I go through 2 steps. First, I do the vertical cuts (step 1). Then do the girdle cut (step 2) to create your final product. The Step 1 cuts need to be made just a hair lower than the actual edge you are looking for. This has two advantages: First it eliminates the problem of mistakenly cutting too high and ruining the edge on your piece or after having to fix an end, trusting that the same error is not made on the other end. Second, by knowing that one is just a hair below the end edge the potential for a problematic shoulder where the cuts meet is greatly reduced.
-
- 0 replies
- 3.3k views
-
-
So ... I have some tools and I know I need to make them work better. Space is a premium (not sure how many people have unlimited space) so the basis for my shop will be a Rigid 4510. I already own it so please don't tell me it's a bad choice. I have the following wood cutting/shaping power tools as a starting point: Rigid 4510 Table SawDeWalt DW715 12" Compound MiterRyobi AP-12 PlanerRyobi R161 1-1/2 HP 1/4" RouterHarbor Freight 8" 5-speed drill press... maybe a couple other random hand tools like a sander and a jigsaw. I was thinking this would be a logical order of projects/jigs to make, each building upon the last's capabilities:True up table sawTable saw sledRou…
-
-
- 27 replies
- 8.7k views
-
-
I have been looking around for a suitable way to hold boards on my bench while planing and other general tasks. Without a tail vise, it becomes difficult to hold varying length boards enough to accomplish anything. I have seen the veritas wonder dog which is about what I'm looking for but just wondering if there are any other alternatives?
-
-
- 43 replies
- 11.6k views
-
-
I know that Festool does a great job on dust control but I found that the last inch of a cut with the tracksaw on the MFT-3 produces a small blowout of dust that is not captured. I designed and made a simple port that slides into their frame profile and fixes the issue. Click here to watch me describe the need and then make it. What do you think?
-
-
- 3 replies
- 3.6k views
-
-
I have a good amount of 1/2" acrylic from a large aquarium that I couldn't salvage and cut down for material. I was wondering if there would be any issue with using it for jigs, mainly for the TS. I was thinking about making a new miter sled for picture frames, and another smaller crosscut sled. I guess the question is whether it would be good to use the acrylic for the bases and maybe runners for these sleds, or if there was an issue (expansion, warping, etc) that I was unaware of. I have MDF on hand to make the bases (obviously wouldn't use for the runners) if that works better, but wasn't sure which material would be the most stable over the longer term. …
-
-
- 10 replies
- 9.6k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·