Recommended Posts

Posted
On 11/9/2023 at 8:12 PM, pkinneb said:

..ahh a picture is in order don't you think?

Not finished yet.  Got some brass to polish and glue up to do and finishing.  Brought it home dry assembled.

 

  • Like 2
Posted
1 hour ago, pkinneb said:

Finished up the rest tonight just need to pick up some additional hardware (washers) and I'll be ready to turn. 

What are you turning that requires a full length tool rest?  Looks great I am just curious what the need is.

Posted

I finished the edge of that floor, and ran the buffer for a little while to see how it would go.   Looks like it will take about one minute per square foot to get it ready for finish.  The room is 192 square feet, so a little over three hours.

My trouble was that the brushes on the bottom of the pad driver, being something around forty years old, had about given up the fight.  The machine was lopsided with old driver.  I can get something done with it, but it's aggravating to run, and probably uses one side of a sanding screen more than the other. 

The bristles are supposed to go straight down.  You can see in the picture that they're all laying over one way.

I ordered another pad driver off of Amazon, and will wait to do more work on it until the new pad driver gets here.

The pad driver brushes sit of top of different kinds of scrubber and polishing pads.  A sanding screen just lays under one of the scrubbing pads to work.

https://www.amazon.com/dp/B00WGQ9J3U?psc=1&ref=ppx_yo2ov_dt_b_product_details

 

IMG_6177.jpg

IMG_6179.jpg

IMG_6181.jpg

  • Like 2
Posted
On 11/14/2023 at 5:50 AM, JohnG said:


Just take one firm and steady pass with the cutter, don’t take multiple passes.

How much are you cutting off? Thin strips are harder to break off cleanly, though it can be done. If it’s a big offcut, just put the glass on a counter or table with a hard corner, with the cut just overhanging the edge and give the offcut a quick push downward (wear gloves if this makes you nervous, it won’t break clean if you hesitate). If it’s a thin offcut, I always had the best luck using a decent pair of linesman pliers.  I never liked the dedicated glass pliers or the ball end of the glass cutter.

A dab of 3in1 oil or similar on the cutting wheel can sometimes help if you aren’t getting a clean break from one firm cutting pass.

I think around 2" on each side. Hopefully that's wide enough for the roughly 22" and 28" spans. Doesn't have to be perfect as it'll be hidden by the frame. Thanks for the tips!

Posted
On 11/13/2023 at 9:37 PM, Coop said:

@Tom King, I like the height of the wainscoting and the fact that the receptacles are in the baseboards. 

Thanks.  That wainscotting is all just box store MDF.

I do the whole job, so can do everything like I want to.  For wiring a house, I pull all the wires but don't mount any boxes until the finish walls go up.  I use the heavy duty old work boxes mounted into whatever the finish wall is and seal around them.  The wires are pushed and pulled into place as the finish wall goes up.

The wires also run in a groove on top of the bottom wall plate and go up where they need to.  That way it's out of the way of the insulation when the insulation is installed.  Walls are thick enough that what nails that are used can't go deep enough to hit a wire.

When I built new houses I did everything, so it was not so much one step at a time, but it all works together.  I had more than one inspector ask me "how did I get that pipe in there?".  I was able to put horizontal runs of DWV pipes in one piece because I put it in there when we built the wall or floor.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 71 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined