Power Tools
4,152 topics in this forum
-
- 7 replies
- 205 views
-
- 5 replies
- 182 views
-
- 1 reply
- 316 views
-
- 4 replies
- 643 views
-
- 11 replies
- 2.3k views
-
- 13 replies
- 516 views
-
- 5 replies
- 569 views
-
- 21 replies
- 503 views
-
- 0 replies
- 257 views
-
- 2 replies
- 717 views
-
- 18 replies
- 854 views
-
- 38 replies
- 21.4k views
-
- 1 reply
- 385 views
-
- 28 replies
- 994 views
-
- 5 replies
- 562 views
-
- 6 replies
- 565 views
-
- 8 replies
- 716 views
-
- 59 replies
- 2.8k views
-
- 4 replies
- 593 views
-
- 23 replies
- 4.2k views
-
- 0 replies
- 468 views
-
- 23 replies
- 41.6k views
-
- 11 replies
- 614 views
-
- 13 replies
- 619 views
-
- 8 replies
- 594 views
-
Who's Online 0 Members, 0 Anonymous, 35 Guests (See full list)
- There are no registered users currently online
-
Forum Statistics
31.2k
Total Topics422.3k
Total Posts -
Member Statistics
23,779
Total Members3,644
Most Online
-
Topics
-
-
Posts
-
I started out many years ago. I had no tools or skill. Tried to make a simple box using a hand miter jig working for what seemed like days to get It just right. When it was done. It looked like a box someone would have made in kindergarten. But I was hooked. I bought a 100.00 dollar table saw and a small drill press. I lived in an apartment with my gf and sister her brother and mother. My table saw was actually our kitchen table had a piece of plywood on it when not in use and my drill press set on an end table. I can remember mother in law using the light on it to read books with. Many years later I’m not much better but my wife and I had a shop built on our property it’s 24x30 and I work part time as a diesel mechanic 3days a week thinking some day I can go full time as a woodworker but the truth is I’ll probably just stay as is I have to many other hobbies it just tie it down to one. -
By wtnhighlander · Posted
I agree that maximizing the use of material feels better, and you did a good job with it. I'll point out that chairs are definitely NOT the right application for a lot of figured grain, at least not crotch figure. Avoiding such grain in mediocre cuts of lumber is often difficult. Straight grain with minimal run out keeps things strong and tight. Your QS oak selection is an excellent choice in that regard. -
By wtnhighlander · Posted
A large portion of my tool kit is inherited, gifted, or purchased used. Consumables aside, I have far less than $5k invested in my shop, and that accrued over a couple of decades. I have, at times, offset the cost of my hobby by actually selling some of my product, but I don't suggest that as a means to really drive the hobby. Makes it seem too much like work. -
Yep, add understanding spouse or non at all, regardless of income, to your decision. -
By Beechwood Chip · Posted
Just as many people replied that "space" is a major frustration in a woodworking hobby, I think the biggest financial drain from woodworking is finding the space for it. I moved from a nice apartment to a run-down house, and a big motivator was so that I could set up a woodworking shop in the basement. Other than that, you can be a very productive hobbyist woodworker with under $1000 in tools, at least according to Steve Ramsey. (The first time I used a router on MDF in my living room, I said, "I either need to give up woodworking or find some dedicated shop space.)
-
-
Popular Contributors
-
1
-
2
-
3
-
4
-
5
-
