Hand Tools


2,042 topics in this forum

    • 5 replies
    • 7.1k views
  1. New toy

    • 2 replies
    • 3.5k views
  2. My #4 is ready

    • 1 reply
    • 3.3k views
    • 9 replies
    • 11.8k views
  3. Vintage Handsaws

    • 12 replies
    • 5.1k views
  4. Spokeshave

    • 3 replies
    • 3.6k views
  5. Lie Nielsen event in my hood?!

    • 15 replies
    • 3.6k views
  6. Tool of choice?

    • 10 replies
    • 3.6k views
  7. How To Hone

    • 13 replies
    • 3.7k views
  8. Shooting board and plane

    • 6 replies
    • 4.1k views
    • 27 replies
    • 8.9k views
  9. High End Plane Blades 1 2

    • 30 replies
    • 11.6k views
    • 7 replies
    • 5.9k views
    • 20 replies
    • 5.1k views
    • 39 replies
    • 18.8k views
    • 15 replies
    • 4.2k views
    • 12 replies
    • 4.5k views
    • 7 replies
    • 3.6k views
  10. Stropping Leather?

    • 3 replies
    • 3.6k views
    • 4 replies
    • 3.5k views
    • 4 replies
    • 3.9k views
  11. Sharpening Options

    • 4 replies
    • 3.6k views
    • 70 replies
    • 17.4k views
  12. Square

    • 4 replies
    • 3.7k views
    • 19 replies
    • 4.7k views


  • Topics

  • Posts

    • The last time I had to route a significant amount of MDF, I opened the door to my shop, positioned a window fan in the door way as exhaust, positioned a pedestal fan between the work and the doorway, ran both air filters, hooked a shop vac to the router, and wore a respirator.  Better safe than sorry. I've found that a dust extractor hooked to the router works well with MDF, but I'd still wear a respirator. Oddly, when I cut MDF on my table saw, I didn't even think about dust.  I've got a Harvey Gyro hooked to the dust port and a shop vac hooked to the blade guard. I like the idea of doing it outside.  A home made circular saw guide will work.
    • Just as an update, having that siding on the North and NE side of our house has made more of a difference than I thought it would.  We're on top of a hill that gets hit directly by any cold wind from the NE.   When it got down to freezing before, we always needed to use the Propane heater in the big room of the original part of this house.  Last night, with a NE wind and temp down to 31, the 24k mini split kept the whole house comfortable.  I think we were losing a lot of heat from that one small section of the house.
    • Yes, it's intended for first design.  I don't even wear a dust mask when using the table saw.
    • Not to argue, but I wouldn't want to dissuade anyone with <3 HP of DC from using it. I have nothing that powerful and while what I have is far from perfect, it does a lot of good.
    • MDF does make a lot of dust, but it does seem to be the easiest for a good DC to take away.   With a 3hp DC we could cut MDF inside houses and not a bit of dust would get on anything.  That did include a well sealed old Unisaw and an overarm dust arm.  I always cut a piece of MDF if anyone asked to see how well it worked. My rule of thumb is anything less than 3hp is wishful thinking.
  • Popular Contributors