Jig & Fixtures
489 topics in this forum
-
This is a rambling tale so feel free to skip ahead. I got lazy and left the HVAC weep drain termination point (small outdoor French drain) stay on the "To-Do" list too long. Result? Weeds grew around the end of the pipe, dirt collected around the weeds courtesy of the wind and the end of the pipe got buried. The drain tube filled up and the inside unit dripped inside . . . right on the bevel sled that was hanging from the cleat peg rack. I knew I shouldn't have run cleats under the unit but I wanted the space . Fixed/finished the drain but the sled was trashed. I needed a bevel sled the other day and I am still waiting for finish to cure on a current project. Our bo…
-
-
- 3 replies
- 3.3k views
-
-
I get asked about these now and again and apparently never posted a build on these. They were made in the garage while I was between shops. Dimensions are nominal. When I make these sorts of things I make a batch (should have made more). I use a strip of old gift card to make a consistent space to allow free sliding movement. Tilt the drill press and drill the peg hole with a Forstner. I drill an 1/8" shy of the back and use glue and a screw to hold the peg. The peg passes through most of two layers of 3/4" ply so the screw is just a retainer, not a strength fastener. As you can see I make these out of any …
-
-
- 8 replies
- 4.1k views
- 1 follower
-
-
@Chetwas kind enough to provide me with a conversion chart for "on center" measurements for the Domino tenon locations a year or so ago which has been very handy. However, I still find myself using scrap pieces when attaching aprons and stretchers to legs to insure a correct reveal or setback. I finally got around to making a jig for this purpose. I'm sure many of you have done the same, but I have not seen them on here.
-
-
- 10 replies
- 5.7k views
- 1 follower
-
-
I decided to build myself a nice pocket hole machine. I wanted something large enough to handle cabinet side panels. I wanted something similar in size to the Castle TSM-22. I only had a couple sketches to go by and pretty much “winged it”. I had a Porter Cable trim router, and a 2 HP Ryobi not being used, so both would be used for the build. I started with the 2 HP router to be used to cut the pocket. I decide to use the base as it would make it easy to adjust the height of the cutter. In hindsight, I should have just used the router motor and used a large U Bolt so reduce the swing angle. It would have reduced the length of the pocket slot. …
-
-
- 15 replies
- 6.7k views
-
-
I was gifted this table and wanted to share the initial experiences with it. When I first saw it I pondered making something myself that could do the job . . . I just never got around to it. Probably just as well since the table is well thought out and fairly functional as designed. Let me start by saying I am a long time Lee Valley fan and sing their praises. I also call folks out when they fall short. That being said . . . The base is made of CNC cut plywood pieces. The cuts were very crude and I had to do a fair amount of sanding to get things to where one wouldn't get a plywood splinter (I hate plywood splinters) while moving the rig from storage to work are…
-
-
- 2 replies
- 6.4k views
-
-
I need to make a few different sleds for my table saw and I'm curious if you all tend to make your own miter bars or buy them for your sleds? Last time I made them and it was challenging. Without moving the table saw fence I found some were too tight and some were too loose. I currently have limited shop time so I was thinking of purchasing some to speed up the project.
-
-
- 14 replies
- 5.2k views
-
-
I told myself that the next time I needed to use the L-fence more than a couple of times I would stop and make a version 2. I failed to do that on the last project but stopped for a bit this morning to slap one together. My first really rough L-fence was based on Bob Van Dyke's original version. I cannibalized some of that jig and based the version 2 on Bob's improved L-fence as seen in Fine Woodworking magazine. I was kind of blasting through it because I wanted to get back to my blanket chest project so the pictures start a little late. I use the router table and fence for long grooves. For shorter dado-like grooves the router sled comes in handy. I g…
-
-
- 2 replies
- 3.9k views
-
-
First, as a newbie, let me say there is a lot of great content in this forum. Thanks to everyone who has shared. I've gotten a lot of great ideas skimming through it. I plan to share some of my jigs from over the years and what I liked about them and what I wished now I had done differently (and what I may do for version 2 now that I'm getting back into woodworking). I welcome any additional thoughts. I'll start with my drill press table. It's about 15 years old, a 2x3/4" MDF carcass with cherry edging, commercial t-track and a cheap commercial aluminum and MDF fence which rides in the outer t-tracks. The carcass is double thick except right over the original dr…
-
-
- 22 replies
- 5.4k views
- 1 follower
-
-
Since I got great suggestions on my drill press table, and since I'm currently a very slow woodworker waiting for Spring with little new progress to show, I'll cover another old project. I build this about 15 years ago. It's the Norm Abrams router table with a commercial Bench Dogs Tools ProFence. I bought a top because I was nervous about my ability to make one. I don't think I'll ever build myself a version 2, but this is due for some modifications. The top on this thing is plenty big. In fact, I often store various things behind the fence more or less permanently. The major thing I wish I had done differently is the upper drawers, which are m…
-
-
- 8 replies
- 4k views
-
-
I keep a folder of wood working things I would like to get around to someday. I am recovering from a torn retina and was setting around feeling bored and morose when I remembered that folder. These are more or less right out of Woodsmith 221 and ShopNotes 116 with modifications to suit my use and preferences. My Delta 17-950 drill press has stuck around basically because I cannot find a better one for even three times what I paid for it. Someday I'll own a big-boy DP but, for now, this one has features and quality that does the job. The one exception (OK, there's more than one but, I digress) is the depth stop. This is the farthest up the old Delta food chain yo…
-
-
- 23 replies
- 10.6k views
-
-
I sold a bunch of dad's turning stuff (still have some to go). I gathered enough to make me finally buy a combo sander that I have been after for about 15 years. It's funny; I wouldn't pay the price back when it was about half of what it is now. I view it as a gift from dad. At any rate with the current prices of new material and the down right unavailability of some others I sat down to percolate. I still have a fair amount of the free material I got from a guy who runs a cabinet shop; it was rain damaged. I decided to see if I could come up with a design that would use the sizes of material I had available. I didn't start taking pictures right away be…
-
-
- 11 replies
- 4k views
-
-
I have been telling myself to setup a temporary mini router table for some time. When I batch things like door frames, box lids, picture frames and such a second profile for the light work could save me some swap over time. We're not talking about anything production level, just a helping hand. I have the making for a second router table but have become selfish with my shop space and am unwilling to commit. A small table for the Bosh Colt seemed like the answer. I have a spare router fence that dad used to use on his drill press but a shop made would do as well. I need four boards of equal thickness and with at least one perpendicular side and end. …
-
-
- 9 replies
- 3.7k views
-
-
There are many plans available on building a jig to flatten slabs, boards etc. The key to any of them is to get the long rails parallel and coplanar with the place you rest your work on. I have a lot of cherry I got inexpensively because many of the boards have about a 1/2” of twist over 4 feet. Building the jig is straightforward, but how do I ensure things are lined up over the 8-12 feet the boards are long? Thanks Ray
-
-
- 5 replies
- 4.9k views
-
-
I've struggled for years to route in these recesses in small boxes for your finger to lift the lids, always burned and almost always had tear out where the router bit left the cut, this process seems to work pretty well, this scrap is 1 1/2" wide, round over on both sides and used PSA sandpaper, mark the center on the box and lid, sand gently at 45 degrees on the lid and box until desired depth is reached, and as an after thought a 45 degree bevel on each side may work better. these are the last batch of recipe boxes in maple that are going out today, if there's any other suggestions out there i would like to hear them.
-
-
- 8 replies
- 3.2k views
- 1 follower
-
-
-
So I have this bandsaw template jig which is my take on one shown in Woodsmith, Shopnotes, or some other magazine that I do not recall. I primarily use it to make odd shapes on the bandsaw more quickly and reliably consistent when several duplicate parts are required. I should mention that in the picture above the lower wooden guide (engaged with the blade) is for tight turns. The one not in use but just parked above on the posts is for more gentle curves. You only use one or the other. I had a fair amount of template routing to do. I used the bandsaw template jig as opposed to "cutting near the line" prior to template routing. You can see the differe…
-
- 2 replies
- 3.6k views
-
-
If I posted this before I can't find it. If it is a repeat . . just move along as if I didn't have a brain-fade . Support for larger case work can be a challenge in a space challenged shop. I have used a variety of fold-and-stow platforms but these torsion beams have remained constant. They are just long torsion boxes. Mine are made from 1/2" MDF for the tops, bottoms, and ribs. 1/4" double tempered hardboard is used for the sides. I leave about an inch of overhang at each side and at each end to give me somewhere to clamp them to whatever is supporting them. This is MDF so these overhangs are only for keeping the beams still and won't take a lot of…
-
-
- 8 replies
- 4.1k views
-
-
What got me started was a redesign of the cheapo router table I currently have, and instead of using wood, I thought about granite like Steel City uses on some of their tools. But then, a friend suggested pouring concrete, and I thought why not? It would be cheap enough that even if it failed spectacularly, it would not be a huge deal. The main attraction is that I can fashion the holes and slots into the mould, which would be much easier than in cutting granite. Are there any serious problems with using concrete? I would need to finish it with something, probably an epoxy or something to make the finish a little lower friction and a little less porous/out of plane. …
-
-
- 61 replies
- 19.6k views
-
-
I have never liked the way I stored my DT saws. I got tired of making planters and "decorating" the back yard and so knocked this out to feel better about myself . I have other saws stored elsewhere but like these three handy. It will set about 4" higher on the tool cabinet door. I have it at this height to build it as I just did it on the fly. Two sides with a dowel between for the bottom. A block with slots and 1/4" x 1/2" rod magnets set into a hole drilled end to end for the top. A drop of CA glue keeps the magnets put once they were positioned although they were tight enough to stay on their own. Now they take up less room and are st…
-
-
- 3 replies
- 3.3k views
-
-
While moving things about I came across a jig accessory that I had cut out but never put together. Took a short break from schlepping lumber to finish this thing off. I had to cut the dovetails in the face plate. The intention is to grip things to the face plate and be able to safely move them through operations. I added a couple of slots so it can also be attached to the new sled although that is not the main use. By its nature it could be used as a tenoning jig. I have a cast iron tenon jig that I prefer. However, my cast iron one will not allow me to make angled tenon cuts Or even more unusual cuts. I designed it with the intenti…
-
-
- 8 replies
- 3.6k views
-
-
I'm still dragging the last few things in from the garage. When you need a pipe clamp, you want a pipe clamp. The rest of the time mine are usually tucked out of site; a rack behind a tool box, behind a door, whatever. For the new shop I want to take advantage of the taller walls for seldom used items. These racks are simple and take up little room. I decide on the blank's dimensions and lay out for the "arms". I drill 1-1/8" holes for 3/4" pipe clamps. I gang the four blanks to saw out the space between the arms. I glue and screw vertical cleats up opposing sides of the blanks . . . sorry, no pics ;-( …
-
- 6 replies
- 3.4k views
-
-
I hope I haven't already done this . I use a shop made flexible sanding block for things like the Scott Lewis cutting board. If you've ever done box joints you already know how to do this. Special jigs are nice but lets pretend all we have is a miter gauge and a sacrificial fence. I use 3/4" MDF so that's what I will demonstrate here. Set your FTG or TCG blade at about 1/8" from the stock's thickness height. Use a blank that is about a foot longer than the block you will cut off of it. Attach a sacrificial fence to your miter gauge and make a cut through your blank and the fence. Please ignore the second narrow cut in the sac fence. That i…
-
- 6 replies
- 3.2k views
-
-
Someone asked about the blast gates I am using. I went to find a link to where I had posted them and could not find one here. Either my Google-Fu has failed me or I never posted this (?). If it's a dup, sorry about that. I made these before the new shop was up so I was limited to the few tools I had in the garage at the time. The point being that some of the methods I am using are due to limitations and not the recommended methods per se . First there was a plan and the plan was good . . . I will have a few variations but, most will be like these; hose on one end and ASTM-2729 pipe on the othe…
-
-
- 11 replies
- 4.9k views
-
-
We all make solutions for our shops. When we need to thread things T-nuts or threaded inserts work well on the receiver end. I use bolts for making a stud. I had already gotten though the first few steps before I realized I should probably share this so you see 1/4" holes instead of 1/16" holes; sue me. In this case I am making a couple of mounting locations for a Veritas tool rest. I mark the spots that I want the studs with an awl. I drill a 1/16" through hole so I have a matched layout on both sides. The picture shows the 1/4" hole but let's not dwell . I use the 1/16" hole on the bottom to position a 7/16" Forstner. This is for a 1/4" hex head. I take the dime…
-
- 0 replies
- 3.6k views
-
-
I hope this isn't a repeat. I had a little spindle work to do today. I had made ver-1 of this idea 6 or 7 years ago out of some scrap from breaking down an old Ikea or Wal-Mart TV stand. Like other things I am sure we all have it has never made it to ver-2 since ver-1 just works. Most of my material that gets spindle sanded is 6/4 or less. This means I only use a portion of the sleeve. I saw some clever guy in one of the trade rags do this after a fashion and stole the idea. I now pass it on once-removed . I have the commercial throat plates for this sander but don't use them with this rig which pretty much lives on the machine. Just in case I …
-
-
- 4 replies
- 3.2k views
- 1 follower
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·